single point load cell Articles

  • 6 Questions to ask when choosing a load cell

    There are many things to consider when choosing the right Load Cell for your application. These are our top 6 questions to ask yourself (or us). What type/style of Load Cell do you require? ...


    By PT Limited

  • The most efficient distance between two points

    When bulk material characteristics, process parameters or space restrictions call for a flexible screw conveyor Deciding on the single most efficient method to move your material from point A to point B is a matter of simple deduction: just match your material flow characteristics, process parameters and space limitations to the performance windows and dimensional restrictions of ...


    By Flexicon Corporation

  • Why are waste operations installing on-board scales?

    Given the rising cost of operating waste collection vehicles, it is becoming more important to evaluate the use of on-board weighing systems to reduce operating costs, meet new safety standards and improve fleet efficiency. Electronic on-board scales are not new. They were introduced more than 30 years ago into trucking applications where monitoring gross vehicle or payload weight was ...


    By Waste Advantage Magazine

  • Typical process weighing applications

    Process weighing relates to the weighing of a powder material as part of a production process. The technology includes continually monitoring a material in a silo, discharging material by weight or rate, or even weighing products on the move. This article gives an overview of most of the typical process weighing applications that are used in all sorts of industries: level or inventory measuring ...


    By Hardy Process Solutions

  • Weigh batching: the benefits of an automated system

    In many plants that batch-blend bulk products, weigh batching is a manual, time-consuming operation in which ingredients are weighed individually before being charged to a blender or other process vessel. A significant number of such plants could benefit from the installation of an automated weigh batching system. For small as well as large operations, an automated weigh batching system can pay ...


    By Flexicon Corporation

  • Membrane Electrode Assembly (MEA) Activation Procedures

    Why is an activation procedure or break-in necessary for a membrane electrode assembly (MEA)?  A large reason for performing an activation procedure or break-in is to properly humidify the membrane portion of the MEA that was dried out during the hot press stage of the membrane electrode ...


    By Fuel Cells Etc

  • SMF4 case study 2

    Sewer Misconnection Survey Date: March 2010 Location: Edgebaston Birmingham UK Purpose: To test the application of the SMF4 portable fluorimeter in the detection and quantification of organic pollution from faecal matter in Surface water Sewers. Background STS was invited independently by the Environment Agency and Severn ...

  • ACO surface water management systems help create award winning retail environment

    Designers of the drainage system at the new Peterborough Garden Park have exploited the benefits of a number of AGO Water Management product ranges to create a value-engineered SUDS solution that has helped the development win the BCSC Out-of-Town Retail Scheme Gold Award. Runs of ACO KerbDrain, AGO Profile, ACO MultiDrain and ACO Brickslot form an integrated network that overcomes the site's ...


    By ACO Group

  • SMF4 case study 3

    Bathing Water Catchment monitoring Date:2010 Location: Bude Cornwall UK Purpose: To carry out a river survey identifying potential pollution sources and their likely impact on bathing waters downstream. Background STS and the Environment Agency have, for some time, been discussing the issue of monitoring water courses which ...

  • Case study - Mobile remediation system

    OVERVIEW A large consulting and contracting firm owns and operates several ex-situ Thermal Desorption Units (TDUs). Each single-load Thermal Desorption Unit has the capacity of desorbing 15 tons of soil per hour at a temperature of 400°F - 900°F. These Thermal Desorber Units have been designed to operate on both chlorinated and non-chlorinated RCRA, CERCLA, and private industry ...

  • Hot springs swimming pool: Glenwood Springs, Colorado case study

    Ozone Water Treatment, Color Removal and Ozone Purification In 1991, the Hot Springs Pool and Lodge Resort installed a DIN-Standard ozonation system for treating the world’s largest hot springs-fed swimming pool. The following main reasons were responsible for this decision: The suppliers of gaseous chlorine had dwindled down to a single source, as it had become ...


    By BiOzone Corporation

  • Paste thickener bed level measurement

    Numerous studies and papers have been devoted to the subject of thickener design and operation to achieve specified throughput and discharge densities. Mathematical models have been developed that present methods for sizing thickeners and predicting performance under varying process conditions. The compression effect of deeper beds on dewatering performance is a recognized phenomenon. This is one ...


    By WesTech Engineering, Inc.

  • Anaerobic Digestion at Dairy Farms

    The need to upgrade dairy waste management practices to overcome pollution problems is leading more farmers to seek solutions with anaerobic digestion technology. Two recent examples of this trend are underway at California sites. The Cal Poly Dairy is located adjacent to the California Polytechnic State University campus in San Luis Obispo. The dairy milks 180 cows with a total population of ...


    By BioCycle Magazine

  • Bed Level Measurement

    Numerous studies and papers have been devoted to the subject of thickener design and operation to achieve specified throughput and discharge densities. Mathematical models have been developed that present methods for sizing thickeners and predicting performance under varying process conditions. The compression effect of deeper beds on dewatering performance is a recognized phenomenon. This is one ...


    By WesTech Engineering, Inc.

  • Vibrating feeders for stockpiling and reclaim

    The expanding applications of vibratory feeders for controlling the flow of bulk materials, and their adaptation for processing requirements, have developed considerable interest in stockpiling and reclaim systems. The general design of these units consists of a material transporting trough, or platform, driven by a vibratory force system. The flexibility and variety of designs is limited only by ...


    By General Kinematics

  • Tech update: Plant instrumentation - food engineering

    Sensors and other devices are the foot soldiers in automation architecture, but most food and beverage manufacturers still are looking for full value. You know an equipment category has arrived when it starts getting its own industry-specific center. For the food production sensors that do the heavy lifting in instrumentation technology, that day could arrive earlier rather than ...


    By Hardy Process Solutions

  • New developments of vibratory feeders for large bulk material reclaim systems

    Summary The efficient economical storage, movement, control and blending of large tonnages at coal handling installations such as mines, power plants and port facilities require new and improved designs of vibratory equipment. Environmental and investment impact as well as operational advantages must be considered in the development of any new reclaim system. ...


    By General Kinematics

  • Wastewater Mining and Reuse: Creating Benign Future Scenarios

    Wastewater mining: In addition to being perhaps the most uninviting combination of words, it sounds like a most unlikely idea. But for almost 30 years, Aqueonics, now headquartered in Greenville, SC, has pioneered such systems, starting in the ’80s, with its first wastewater mining project. For that project, Aqueonics provided an onsite or decentralized treatment system for a developer in ...


    By Aqueonics, Inc.

  • Odor Control Advances at Composting Facility

    The Rockland County (New York) Cocomposting Facility began operations in February, 1999, processing biosolids from the five publicly owned treatment works (POTWs) in the county. The Rockland County Solid Waste Management Authority (RCSWMA) owns the facility, but contracted with Waste Management of New York to design, build and operate (DBO) the 110 wet tons/day agitated bin composting facility ...


    By BioCycle Magazine

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you