treat drill cuttings Articles

  • Drilling oil recovery from drill cuttings - Case study

    Recovery of drilling oil and drilling fluids from different drill cuttings Drill cuttings are an increasing waste stream worldwide, econ industries addressed the challenge by developing a process that cleans the waste and at the same time recovers valuable drilling oil. The VacuDry® plant started the successful processing of drill cuttings in autumn 2013. ...

  • Nigerian drilling platforms wastewater treatment

    Wastewater on a self-contained drilling platform comes from several sources. The following examples are samples obtained from the seven oil-drilling platforms off of the coast of Nigeria. The first platform had samples from the industrial laundry, kitchen, emulsified wastewater, cutting oily-water and drilling mud. The samples were treated individually and then combined so as to simplify the ...


    By Integrated Engineers Inc.

  • Oil Drilling Operation Wasteawater Treatment

    Wastewater Treatment Success Stories Oil Industry Operation Wastewater Treatment Wastewater on a self-contained drilling platform comes from several sources. The following examples are samples obtained from the ...


    By Integrated Engineers Inc.

  • Case Study: Nigerian Drilling Platforms

    Wastewater on a self-contained drilling platform comes from several sources. The following examples are samples obtained from the seven oil-drilling platforms off of the coast of Nigeria. The first platform had samples from the industrial laundry, kitchen, emulsified, cutting oily-water and drilling mud. The samples were treated individually and then combines so as to simplify the platform ...


    By Integrated Engineers Inc.

  • Drill King International is exploring reverse-circulation drilling opportunities in Chile

    The new XT RC50 hammer from Drill King International completed drilling trials at the beginning of August 2016. This 5in (127mm) reverse-circulation (RC) hammer is the first one from the XT (Extreme Torque) series, introduced by the down-the-hole (DTH) drilling equipment manufacturer from Texas, US. The XT RC hammer series will complement Drill King's extensive line of DTH air- and water-powered ...

  • Case study: Contract title - ADCO Drilling Operations

    Contract Location: Habshan, U.A.E. Contract Start Date: 10/2002 Contract Finish Date: 2005 Quantity Treated (m3): 30,000 tons Treatment Method: Thermal Desorption Rate of Treatment (m3/hr): 3.5 to 4.5 tons per hour (dependent upon feed) Working Hours per Day: 24 Working Days per Week: 5.5 Project Description: RLC Technologies contracted to ...


    By RLC Technologies, Inc.

  • Case study - Superfund site, water pump & treat system

    Anguil Aqua Systems LLC was contracted as part of a team of companies to implement a ground water pump and treat system intended to remove trichloroethylene (TCE) from a local aquifer designated as a Superfund Site by the Environmental Protection Agency (EPA). Though the site is nestled between the buildings and roadways of an existing and operating industrial facility, the overall extent of the ...

  • Getting ahead of the Caribou - pitdry process—innovative solidification solution for spent drilling fluids

    An oil company has been producing oil and gas in British Columbia’s Southern Foothills since 1992. The operator has continuously invested in the area and recently opened up new gas producing wells northwest of Fort St John, the largest city in the northeast region of British Columbia. The new wells are situated 4,600 feet above sea level in a rigid mountain terrain. The viable way to connect the ...


    By CETCO Energy Services

  • Oil Industry Operation Wastewater Treatment Summaries

    Oil Industry Operation Wastewater Treatment Wastewater on a self-contained drilling platform comes from several sources. The following examples are samples obtained from the seven oil-drilling platforms off of the coast of Nigeria. The first platform had samples from the industrial laundry, ...


    By Integrated Engineers Inc.

  • MB Bioremediation - Case Study

    Patented dry product delivering billions of live non-genetically modified microorganisms for bioremediation of oil, gasoline, diesel, grease or any other hydrocarbon based contamination. MB Bioremediation Drill Cutting Remediation Emergency Public Area Clean-up & Treatment Industrial Remediation Oil Production Pit Remediation ...


    By DryLet

  • Ivey-sol surfactant enhanced soil washing technology overview and project experience - Case Study

    lvey-sols soil washing is an ex-situ surfactant enhanced remediation (SERS) treatment method which removes hazardous substances from contaminated soils, solids, tank bottom sludge, drill cuttings, drilling muds, etc. The soil washing process (Photol) involves the introduction of the contaminated solids into a treatment chamber which contains an Ivey-sol2 formulation and water, at a specified ...


    By Ivey International Inc.

  • South East framing review

    Drilling a borehole on a farm can cost less than a conventional water supply and cut the carbon footprint from pumping and treating mains water. "There is an environmental as well as a cost argument for drilling a borehole,' said Ben Nicholls, joint managing director with his brother Richard of Nicholls Boreholes, which is based in West Sussex. Nicholls Boreholes is in an office on an ...

  • Case Study: Contract Title - WES

    Contract Location: Safat, Kuwait Contract Start Date: July 2005 Contract Finish Date: November 2005 Manufacturing Complete and Plant Shipped Quantity Treated (m3): In excess of 75,000 tons Treatment Method: Thermal Desorption Rate of Treatment (m3/hr): 3.5 tons per hour Working Hours per Day: 24 Working Days per Week: 5.5 Project Description: ...


    By RLC Technologies, Inc.

  • Understanding the potential class II – Division I Safety Hazards present when operating Vertical Cuttings Dryers

    For decades, the industry standard for waste management dryers (a.k.a. vertical cuttings dryers) has relied on belt-driven sheaves. Though belt-driven systems are cost effective and relatively easy to implement, at a minimum they have represented a maintenance nuisance, at worst they represent a serious safety concern when ...


    By Elgin Separation Solutions

  • Working safely around hazardous materials and contaminants

    The first step in working safely around hazardous materials should always be a hazard assessment review. The OSHA standard mandates companies must conduct a hazard assessment to identify the appropriate personal protective equipment (PPE) and properly train employees on how to use it. OSHA compliance officers will review written hazard assessments for completeness and accuracy. In the case of ...

  • Contaminated soils and sludge treatment plant - Case Study

    Client: Ecosistem Group, Lamezia Terme (CZ) – Italy Challenge: to transform waste into product! The Client possesses a large plant for the treatment of products contaminated with hazardous substances and materials, recycling of recovered materials and disposal of non-recyclable waste, which is considered highly ...


    By Baioni Crushing Plants Spa

  • Automotive: At Sandvik Coromant, Clean Air Group Scrubber Handle Emissions Emergencies case study

    Mr. Tahvanainen heads up a staff of eight maintenance personnel and a supervisor. He is a mechanical engineer with a background in power production and thermodynamics. Editorial Background: Sandvik Coromant of Fair Lawn, NJ is part of Sandvik’s tooling division. The overall Sandvik Corporation employs 35,000 in one hundred and thirty (130) countries. ...


    By CR Clean Air Group, LLC

  • Taxpayer dollars subsidizing destruction

    One way to correct market failures is tax shifting—raising taxes on activities that harm the environment so that their prices begin to reflect their true cost and offsetting this with a reduction in income taxes. A complimentary way to achieve this goal is subsidy shifting. Each year the world's taxpayers provide at least $700 billion in subsidies for environmentally destructive activities, such ...


    By Earth Policy Institute

  • Do You Need a Microfiltration or Ultrafiltration Membrane System for Your Plant?

    Determining whether or not an industrial plant needs a microfiltration (MF) and/or ultrafiltration (UF) membrane system isn’t always as straightforward as it seems. While these systems are not essential for every industrial process, when thoughtfully implemented within an intake, process, or waste stream, they can go a long way in improving a facility’s efficiency and/or cutting ...


    By SAMCO Technologies, Inc.

  • Standard Chlorine of Delaware Remediation

    By designing a 70-foot deep barrier wall, Black & Veatch was able to cut off contaminant source areas from a creek near New Castle, Delaware. The groundwater treatment system that Black & Veatch designed prevents site contamination from reaching the underlying drinking water aquifer. The Standard Chlorine of Delaware Site is a 65 acre area including an abandoned chlorobenzene ...


    By Black & Veatch Corporation

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you