turbidity measurement Articles

  • Turbidity Measurement - Not Only Nephelometric At 90°

    This article was featured in Lab Asia - July/August 2008 Turbidity can be described only with limitations as a physical and technical measurement category. The unusual nature of the turbidity measurement in comparison to other parameters can be recognised already in its historical development: Initially a procedure was introduced by Jackson and Whipple around 1900 determining turbidity by ...


    By WTW - a xylem brand

  • How & When We Measure Turbidity

    Turbidity, along with Suspended Solids, is a way of measuring the clarity of a body of water, and how many particles are affecting it. The difference is that while Suspended Solids describes the density of the materials in the water, Turbidity describes how those materials affect light passing ...


    By Partech (Electronics) Ltd.

  • Research on PWM applied in water turbidity measurement

    In this paper, three common measuring methods for the principles of water turbidity, namely, scattering, transmission and the ratio method are introduced. A method combined with modulation and demodulation techniques based on pulse width modulation (PWM) pulse for turbidity measurement using light intensity modulation is proposed. The experimental system that is, the realizing circuit of ...


    By IWA Publishing

  • What is turbidity?

    Turbidity measures the relative clarity of a water sample. It is determined by the amount of scattering that occurs when a light source is shined through a water sample. Light scattering is caused by increased concentrations of suspended particles in water that are not individually visible to the naked eye, which can give the water a cloudy appearance. This parameter is used as a general ...


    By MANTECH Inc.

  • A Treatise on Turbidity and TSS

    When two distinct physical parameters are used interchangeably, an intimate understanding of both is in order to know when this is justifiable.  Two such parameters are turbidity and total suspended solids.  In many industries today the concentration of total suspended solids is of utmost importance to quality control and process optimization.  However, the measurement most often employed is ...


    By Orival, Inc.

  • Real-time control of sewer systems using turbidity measurements

    Real-time control (RTC) of urban drainage systems has been proven useful as a means to reduce pollution by combined sewer overflow discharges. So far, RTC has been investigated mainly with a sole focus on water quantity aspects. However, as measurement techniques for pollution of wastewater are advancing, pollution-based RTC might be of increasing interest. For example, turbidity data sets from ...


    By IWA Publishing

  • Turbidity Measurements in Drinking Water, Effluent Discharges and Coagulant Controlling

    This month at Partech Water Instruments we’re talking about our turbidity sensors—fantastic to use as an environmental indicator. So how can they be used? We’re here to tell you about turbidity sensors being utilised for drinking water, effluent discharges and coagulant controlling. Turbidity Sensors and Drinking Water Turbidity sensors ...


    By Partech (Electronics) Ltd.

  • Turbidity - A Meaningful Parameter For Drinking Water

    This article was featured in International Labmate - July 2008 Turbidity measurement represents a method appearing quite simple with a very complex background. Its complexity is shown by the fact that possibilities for objective and reproducible measurements were developed just about in the 2nd half of the 20th century. Turbidity is caused by dispersion of undissolved particles ...


    By WTW - a xylem brand

  • A novel image processing-based system for turbidity measurement in domestic and industrial wastewater

    Wastewater treatment facilities are continually challenged to meet both environmental regulations and reduce running costs (particularly energy and staffing costs). Improving the efficiency of operational monitoring at wastewater treatment plants (WWTPs) requires the development and implementation of appropriate performance metrics; particularly those that are easily measured, strongly ...


    By IWA Publishing

  • Comparing Optical Turbidity With LISST-ABS

    For measuring suspended sediments, the use of optical backscatter sensors or other turdibity sensors is widespread. At the same time, it is understood that these sensors respond to total particle area, not volume or mass. In other words, optical turbidity sensors have this property: their sensitivity decreases with increasing grain size. The decrease follows 1/diameter. This has been published ...


    By Sequoia Scientific, Inc.

  • TURBIDITY BARRIER ULTIMATE GUIDE

    TURBIDITY BARRIER ULTIMATE GUIDE Definition Floating turbidity barriers (a.k.a. silt curtains, silt boom, sediment curtain) are a temporary in-water sediment barrier consisting of a continuous geotextile fabric curtain suspended from a flotation device on the water surface and held in ...

  • Turbidity tubes for drinking water quality assessments

    Turbidity tubes have been considered to be the field method of choice for drinking water quality monitoring in resource-limited contexts because of their relative simplicity and low cost in comparison with conventional (nephelometric) turbidimeters. These tubes utilise the principle of visual extinction of a submerged target for turbidity determination and were therefore thought to be subject to ...


    By IWA Publishing

  • How & Why We Measure Suspended Solids

    In case you weren’t sure, Suspended Solids is simply a density measurement used to describe exactly how much waste sludge and particles are in the water, and is measured in milligrams per litre (mg/l), grams per litre (g/l) or percentage solid (%). 1000mg/l = 1g/l = 0.1%. It is used to calculate the amount of material, or load, in a wastewater or industrial system. Suspended Solids ...


    By Partech (Electronics) Ltd.

  • Radar measurement in the North Sea

    Background / Task The NLWKN operates the barrier in the inland waterway of the river Ems. They are working with a dense monitoringnetwork which is required e.g. for the preservation of evidence in case of blocks for the protection against storm tides or if the water depth has to be increased to make the Ems navigable for big vessels coming from the dockyard. After an average a new radar ...


    By OTT HydroMet

  • Natural ferrihydrite as an agent for reducing turbidity caused by suspended clays

    Biologically impaired waters are often caused by the turbidity associated with elevated suspended sediment concentrations. Turbidity can be reduced by the addition of positively charged compounds that coagulate negatively charged particles in suspension, causing them to flocculate. This research was conducted to determine the effectiveness of ferrihydrite, a poorly crystalline Fe oxide, as a ...

  • Exclusive: Introducing the new TurbiTechw2 D-ISO turbidity sensor

    We have some exciting news and you are the very first to read about it! This 2nd – 3rd November at the WWEM Show in Telford we will be launching the latest sensor in ...


    By Partech (Electronics) Ltd.

  • New MANTECH Turbidity Flow Cell and Method - Case Study

    Man-Tech’s Turbidity Flow Cell and Method only requires calibrations every 1-3 months. Man-Tech’s automated turbidity has many benefits that make it work well: the sample is mixed to ensure homogeneity, excellent and stable calibrations, easy to add additional parameters including pH, conductivity, alkalinity, colour, and flouride, among other reasons. Why does ...


    By MANTECH Inc.

  • Drinking water quality control: control charts for turbidity and pH

    Water treatment processes are required to be in statistical control and capable of meeting drinking water specifications. Control charts are used to monitor the stability of quality parameters by distinguishing the in-control and out-of-control states. The basic assumption in standard applications of control charts is that observed data from the process are independent and identically ...


    By IWA Publishing

  • Can I measure monochloramine on a palintest photometer?

    Normally, DPD 1 gives free chlorine Addition of DPD 3 (excess KI) gives free and combined chlorine (chloramine) Instead of DPD 3, DPD 2 is used (which has a trace of KI).  This only reacts with monochloramine.  So subtracting the DPD 1 result gives the level of monochloramine.  DPD 2 part code is 1177203 priced the ...


    By Camlab Limited

  • Natural ferrihydrite as an agent for reducing turbidity caused by suspended clays

    Received for publication October 22, 2008. Biologically impaired waters are often caused by the turbidity associated with elevated suspended sediment concentrations. Turbidity can be reduced by the addition of positively charged compounds that coagulate negatively charged particles in suspension, causing them to flocculate. This research was conducted to determine the effectiveness of ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you