ultrasonic gas flow meter Articles

  • DFM 5.0 doppler flow meter for frac sand slurry flow monitoring

    CanFrac Sands Ltd. of Lloydmister Saskatchewan (Canada) needed a flowmeter that could accurately measure sand slurry flow without being damaged by this highly abrasive product. They selected the Greyline DFM 5.0 Doppler Flow Meter with a clamp-on ultrasonic sensor mounted on the outside of a pipe. CanFrac produce “fracturing sand” used by the oil and gas industry. This special type of ...


    By Greyline Instruments Inc.

  • Gas Mass Flow Metering - Innovations Promise More Economical Choices- White Paper

    Introduction As the drive towards energy independence in the United States continues at full speed, oil and gas companies are turning to hydraulic fracturing to increase production. Increasingly stringent state and national regulations for flare gas in particular now require the installation of mass flow measurement instruments to measure waste and excess gases burned off as a result ...


    By Sierra Instruments, Inc.

  • Non-contacting solution for Plugged off flow meters in the oil patch - Case Study

    For years Petrobakken Energy Ltd. used inline turbine flow meters to track the flow rate of oil recycled to treaters. But with a high concentration of wax and sand in the oil, the turbine meters were quickly plugging off. The line had to be shut down at least once a day and the turbine flowmeters disassembled for cleaning. This was troublesome and expensive. Petrobakken knew there had to be a ...


    By Greyline Instruments Inc.

  • Two Technologies for Flow Measurement from Outside a Pipe

    Doppler and Transit Time are two very popular types of flow meter for non-invasive measurement of flow in full pipes. We tend to confuse these technologies because they are both ultrasonic and both measure flow by using sensors clamped onto the outside of a pipe. In the real world they actually work best in opposite applications. Success in your installation depends on understanding the ...


    By Greyline Instruments Inc.

  • Tuning Your Boiler for EPA Boiler MACT Compliance

    The EPA’s Boiler MACT regulations are heating up. Boiler MACT is an EPA rule to limit hazardous air pollutants (HAP) from commercial and industrial boilers and process heaters. Originally proposed in 2011 as a mandate driven by the Clean Air Act,  the rules are Area Source Boiler MACT 40 CFR 63, subpart JJJJJJ for smaller boilers (stores, hotels, apartments, ...


    By Sierra Instruments, Inc.

  • Case study - Petrobras - Natal, Brazil

    Service: SmartBall - Oil Leak Detection Client: Petrobras Project Date: October 2010 Type of Pipeline: Multi-phase product Diameter: 12-inch Pipe Material: Steel Length: 20,900 meters Flow Rate: 0.3 – 0.6 m/s (1 ft/s) Pressure: 90-150 psi Temperature: 35◦ C Results: 3 simulated leaks created and ...


    By Pure Technologies

  • Texas Instruments - A Novel Separation Technique for the Analysis of Trace Levels of Atmospheric Contaminants in Inert Semiconductor Process Gases

    A NOVEL SEPARATION TECHNIQUE FOR THE ANALYSIS OF TRACELEVELS OF ATMOSPHERIC CONTAMINANTS IN INERTSEMICONDUCTOR PROCESS GASES J. Scott McWilliams, Alan Johnson, Charlene Long, Jeremiah D. Hogan*Texas Instruments, Inc.Dallas, TX 75265 Low ppb detection limits for contamination in cylinder gases have been achieved with gas chromatography using a modified gas ...


    By Environics, Inc.

  • Field Performance Testing for Pipeline Pumps

    Significant energy savings can be achieved by optimizing pump operating efficiency. Measuring the exact pump performance with crude oil under realistic conditions in the field is the first step towards improving the pump efficiency in the future. About 20 billion barrels of crude oil were transported through pipelines in 2015. Around the world, there are over one million kilometers of ...


    By Sulzer

  • Sick-building syndrome and building-related illness

    Significant health problems linked to very poor indoor air qualityIndoor Air Quality (IAQ) deals with the content of interior air that could affect health and comfort of building occupants. The IAQ may be compromised by microbial contaminants (mold, bacteria), chemicals (such as carbon monoxide, radon), allergens, or any mass or energy stressor are more prevalent than anyone could have predicted. ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you