water well drilling machine Articles

  • Raw material cycle: from chip to briquette to product - Case Study

    Thanks to their briquetting system from RUF Frischhut can redeploy production scrap and melt it again Ludwig Frischhut GmbH and Co. KG have closed the circle on their raw material cycle by utilising a briquetting press from RUF: cast chips produced during the machining of parts for water supply and sewage disposal are pressed to solid briquettes and then melted in the in-house foundry and ...

  • Drill King International is exploring reverse-circulation drilling opportunities in Chile

    The new XT RC50 hammer from Drill King International completed drilling trials at the beginning of August 2016. This 5in (127mm) reverse-circulation (RC) hammer is the first one from the XT (Extreme Torque) series, introduced by the down-the-hole (DTH) drilling equipment manufacturer from Texas, US. The XT RC hammer series will complement Drill King's extensive line of DTH air- and water-powered ...

  • Degassing Refrigerators - Drill-head and Piercing-plier

    1. For what purpose do we have to degas a refrigerator? A refrigerator has to be disposed as hazardous waste. The refrigerants inside a hazardous refrigerator are harmful for the environment (ozone depleting and greenhouse effect). Most common refrigerants are; R12, R134a and R600a. The uncommon is the removal of NH3. Refrigerants are developed to dissolve very easily into ...


    By ATN Engineering B.V.

  • Case study - One-pass-trencher used to repair Tyler Dam

    Greg DeWind takes pride in his one-pass trenching machine. With a smile on his face, he watches Wednesday as it is used to dig a trench at the Lake Tyler Dam. The 225,000-pound, 3,000-horsepower machine mixes soil, cement and bentonite clay as it cuts a trench that is 2 1/2-foot wide and about 70 feet deep, according to Steve Richards, with ETTL Engineers and Consultants. It burns about 100 ...

  • Ground Penetrating Radar Evaluation of Concrete Tunnel Linings

    Abstract - Ground penetrating radar was used to map tunnel lining condition and locate concrete deterioration and voids in a continuous and non destructive manner. GPR surveying of Kapoor Water Supply Tunnel, Victoria, Canada was carried out with a 1000 MHz Sensors and Software Ltd., Conquest system mounted on a custom built cart. This 8.8 km long 2.3 m diameter concrete lined circular tunnel was ...


    By SewerVUE

  • Case study - net zero energy & LEED

    Anna Maria Historic Green Village (HGV) is a unique, sustainable commercial development in Anna Maria, Florida.  The village is comprised of five buildings.  Four of the five are renovated historic buildings and one is new construction.  The campus is a mix of retail spaces, office and residential units.  One of the HGV developer’s goals is for the entire campus to ...


    By Powerhouse Dynamics

  • Installing gravity sewer in tough Georgia rock

    It took a contractor who was receptive to an innovative new installation approach, a good deal of patience and a whole lot of determination — after two previous attempts by other contractors using drills and air hammers were unsuccessful — to finally conquer a pesky 800-foot (243.8 m) stretch of tough Georgia blue granite. Hence, project owner Coweta County Water and Sewer Authority ...


    By Vermeer

  • Automotive: At Sandvik Coromant, Clean Air Group Scrubber Handle Emissions Emergencies case study

    Mr. Tahvanainen heads up a staff of eight maintenance personnel and a supervisor. He is a mechanical engineer with a background in power production and thermodynamics. Editorial Background: Sandvik Coromant of Fair Lawn, NJ is part of Sandvik’s tooling division. The overall Sandvik Corporation employs 35,000 in one hundred and thirty (130) countries. ...


    By CR Clean Air Group, LLC

  • Economy in car-making - powder metallurgy

    Powder metallurgy (PM) has made a major contribution to the technology of automotive manufacture over the past 70 years. It has been and is still the fastest-growing metalworking technology. Today, on average, it provides about 10kg of the total components of a car — more in the US, where cars are larger and use automatic transmissions in nearly all units sold and less in Europe and Japan, ...

  • Interview with Ronald Ebelhar, 2015 Chairman of the ASTM Board

    Ron Ebelhar has provided leadership in civil engineering projects and ASTM technical committee work since the 1970s. This year, he brings his experience to his elected position as chairman of the ASTM board of directors. You have worked on dozens of engineering projects since getting your degrees in civil engineering. What are some of the most interesting and challenging jobs you ...


    By ASTM International

  • Zero Waste World - When the economy goes in circles, everybody wins.

    “Don’t let fashion go to waste,” says H&M, the global clothing retailer that booked $20 billion in revenues last year. So I brought a bag of old T-shirts, sweaters and khaki pants to an H&M store in Washington, D.C., where it took them, no questions asked, and gave me a coupon for 15 percent off my next purchase. H&M takes back clothes in all of its 3,100 stores in ...


    By Ensia

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you