191 products found

products

  • Augering & Soil Sampling Equipment

  • Model E - Heavy 53 mm Sample Ring Kit

    Model E - Heavy 53 mm Sample Ring Kit

    The sample set with postfix SE, for very hard soils, can be used to take samples in virtually all soils. The samples can be taken on the surface, in auger holes or in profile pits, above as well as under the groundwater level. The heavy duty closed ring holder in this set is fitted with a conical threaded connection which means that the ring holder may also be hammered into the soil with an impact absorbing hammer.

  • Van der - Horst Core Sampler

    Van der - Horst Core Sampler

    The Van der Horst core sampler is used for manual filling of the stainless steel sampling tubes. Sampling can take place in bore holes, casing tubes (minimum diameter 75 mm) or in the beds of canals, lakes, etc. up to a depth of approximately 10 m. By contrast to the Akkerman core sampler the Van der Horst sampler is entered into the bore hole using extension rods.

  • Model 04.09 - Peat Sampler Set

    Model 04.09 - Peat Sampler Set

    The stainless steel peat sampler is in fact a kind of gouge auger. The peat sampler is pushed into the soil manually. The sample containing part is a half cylinder. The peat sampler distinguishes itself from the standard gouge auger as its cone is massive. The sample containing section is sealed off by a plate (fin) that can pivot around the axle in the middle of the sampler and that is fitted with a cutting edge on one side. Having arrived at the...

  • Akkerman - Core Sampler Set

    Akkerman - Core Sampler Set

    Using the Akkerman core sampler, samples are taken in stainless steel sampling tubes in auger holes or casing tubes (above as well as under the groundwater level, casing tubes with minimal diameter 100 mm) up to a maximum depth of 50 m. The Akkerman core sampler is used in combination with a tripod and hand winch. The sampling tube is beaten into the soil using a falling hammer. After sampling the sampling tube can be sealed off with the PE covers. A...

  • Wardenaar - Model 05.09 - Peat Profile Sampler

    Wardenaar - Model 05.09 - Peat Profile Sampler

    Until recently, sampling undisturbed peat profiles in peat lands, was a very difficult activity. Digging and sampling profile pits in most peat lands is difficult (if not impossible) as they would immediately fill with water and the walls would slump.

  • 10 x 5 cm, 50 cm Profile Sampler

    10 x 5 cm, 50 cm Profile Sampler

    The profile sampler allows taking of a sizeable and virtually undisturbed sample up to a depth of approximately 40 cm (10 cm wide and 5 cm across). All roots, up to a cross-section of 2 cm, are included in the sample. When sampling, both U-shaped gutters are pushed alternatingly into the soil, until the required depth is reached, after which one side of the handle is pulled sharply upwards and the other pushed downwards, thus clamping the profile. The...

  • Model RAW-2000 - Core Cutter Method

    Model RAW-2000 - Core Cutter Method

    The set with the equipment for the core cutter method is used for other applications as the soil sample ring kits described before. The set is especially used for works of civil engineering construction.

  • Split Tube Sampler

    Split Tube Sampler

    The split tube sampler is an apparatus for rapid undisturbed sampling at the surface. The apparatus is very suitable for research on root systems, fertilizing and soil biology. The set consists of a split tube sampler with a handle with beating head, hammer with nylon heads (shock-absorbing), sample liners, storage containers and a steel lifting jack with lever and chain. The split tube sampler consists of two stainless steel tube halves with a...

  • Eijkelkamp - Model 01.11.SO - Auger Set for Heterogeneous Soils

    Eijkelkamp - Model 01.11.SO - Auger Set for Heterogeneous Soils

    01.11.SO. Augerings and samplings in homegeneous soils (soils with an uniform soil profile), in almost all cases can be executed with one type of auger. For augerings in heterogeneous soils (soils with a layered soil profile), several different auger types will be applied. This has led to the composition of an auger set for heterogeneous soils. With the standard set it is possible to execute manual augering to a depth of 5 meter, without great...

  • Eijkelkamp - Model 04.06 - Gouge Auger Set for Top Layers

    Eijkelkamp - Model 04.06 - Gouge Auger Set for Top Layers

    A correctly dosed fertilization is a condition for high yield and good quality. From economic and ecological perspectives it is therefore necessary to check the state of the soil. After analysis of the samples taken with this set it is possible to determine a fertilization program. Two gouge augers have been included in the set for sampling top layers.

  • Soil and Sediment Sampling

  • Model 04.15.SB - Hard Soils 7m Liner Sampler Stand Set

    Model 04.15.SB - Hard Soils 7m Liner Sampler Stand Set

    With these sets, with conical screwthread connection, undisturbed soil samples can be taken in a thin walled tube applying a stainless steel core sampler with sample tubes and cutting head. In soft soils the sampler is pressed into the soil, possibly using the push-/pull handle. In hard soils the sampler tube can be driven into the soil using the hammer with two nylon heads (shock-absorbing) or the down-the-hole hammer. The set contains, among other...

  • Model C, Ø 53 mm - Soil Sample Ring Kits

    Model C, Ø 53 mm - Soil Sample Ring Kits

    The sample sets with postfix SC, for very hard soils, can be used to take samples in virtually all soils. The samples can be taken on the surface, in auger holes or in profile pits, above as well as under the groundwater level. The closed ring holder in this set is fitted with a conical threaded connection which means that the ring holder may also be hammered into the soil with an impact absorbing hammer.

  • 5 m Rod Operated Multisampler

    5 m Rod Operated Multisampler

    The multisampler has been developed originally for sampling of wet, solid as well as fluid material. The standard set is suitable for sampling up to a depth of 5 meter. The materials used for the multisampler are stainless steel, NBR- rubber (the piston) and transparent acrylic plastic (sampling tube).

  • Model 04.29 - Standard Set Free-Fall Corer

    Model 04.29 - Standard Set Free-Fall Corer

    The free-fall corer is a sampling tool for fairly undisturbed sampling from the top layer of submerged sediments either or not consolidated. The free-fall corer consists of a frame with strengthening ribs, falling weight and sampler. Using a hoisting unit (davit) on board of a boat the sampler is lowered in free fall. By its own weight and velocity the apparatus penetrates the submerged soil.

  • Ekman - Model 04.34 - Grab Set

    Ekman - Model 04.34 - Grab Set

    This grab is intended for use in soft sediment that is free from plant growth. Two thin hinging flaps are open while the grab is lowered. The flaps close when a drop-weight is dropped (cable operated) or a button is pressed (rod operated). Samples can, therefore, also be taken from very soft top layers. The pressure of the sample prevents much loss of material. Nevertheless, small stones or stalks may prevent the grab from closing properly, in which...

  • Watertrap - Model 12.02 - Water Sampler

    Watertrap - Model 12.02 - Water Sampler

    The sampler ‘Watertrap’ has been designed to take representative samples from running water up to a depth of approx. 25 meter. Samples are taken with the stainless steel device by catching part of a horizontal moving column at a certain moment at a certain depth.

  • Metha - Model 04.10.SA - Soil Corer Set

    Metha - Model 04.10.SA - Soil Corer Set

    A compact, multifunctional corer for taking soil samples (possibly containing volatiles). The 16-ml (about 25 g) soil samples are cut from above the ground surface. They can then be packed so that they are protected from sorption (without synthetic materials), leakage and diffusion, and are then refrigerated or frozen. Analysis subsequently takes place within 48 hours or two weeks. The methanol conservation method can also be used. An ejector presses...

  • Model 04.31 - Delft Bottle Suspended Load Sampler

    Model 04.31 - Delft Bottle Suspended Load Sampler

    This sampler is used to measure suspended sediment transport in rivers and other water courses, from the surface down to 0.1 m above the river bottom. The sediment containing water flows through a bottle shaped sampler. The shape of this sampling body induces a low pressure at the rear face in such a way, that the water enters the nozzle of the sampler with almost the same velocity as the undisturbed flow. The sharp decrease of the velocity in the...

  • Model 04.16 - Soil Coring Kit for Chemical Soil Research

    Model 04.16 - Soil Coring Kit for Chemical Soil Research

    Soil sampling for the determination of the presence of very volatile components such as benzene, toluene, xylene and  chlorinated hydrocarbons should be executed with samplers that prevent the sample from being exposed to air. Preferably the sampling must be done without disturbance of the soilaggregates to prevent mixing with air.

  • Model 13.50 - Visibility Disc

    Model 13.50 - Visibility Disc

    The visibility disc according to Secchi is a simple, although not very accurate, means of determining the visibility depth. The visibility disc is lowered into the water with a wire. When the disc is no longer visible in the water, a reading of the depth is made by means of the marks on the rope. The disc is lowered another 0.5 meter and is pulled up slowly. The second reading is done when the disc becomes visible. By taking the arithmetic mean from...

  • Field Measurement Equipment

  • Eijkelkamp - Penetrologger with GPS Standard Set

    Eijkelkamp - Penetrologger with GPS Standard Set

    The resistance to penetration is a means of determining the ground load-bearing capacity, and the ease with which roots will grow through the ground (important when agricultural, rural- and civil engineering techniques are involved). The resistance to penetration is a mechanical characteristic that, given a certain texture, depends on changing parameters such as degree of humidity, density and the strength of the connection between mineral particles....

  • Aardvark - Model 09.12.SA - Aardvark Automatic Permeameter

    Aardvark - Model 09.12.SA - Aardvark Automatic Permeameter

    The Aardvark permeameter is a fully automated constant-head borehole permeameter to measure soil hydraulic conductivity (Ksat) and other related parameters like sorptivity and percolation in the field. The set can be installed easily and can be used to a depth of 15 m. The permeameter is available for use with a laptop/tablet and for use with a (flash) logger.in

  • Eijkelkamp - Model 08.15 - Soil Sampling and Classification Set

    Eijkelkamp - Model 08.15 - Soil Sampling and Classification Set

    Soil research is a very important aspect in the planning and execution of agricultural- as well as civil engineering and operations. In order to make the soil research as comprehensive as possible the following studies must be made with regards to: The build up of a soil; i.e. determining the composition, the thickness and the position of the various strata. The soil properties; measuring the permeability, the filtration capacity, the bearing...

  • Eijkelkamp - Model IB 06.06 - Hand Penetrometer for Top Layers

    Eijkelkamp - Model IB 06.06 - Hand Penetrometer for Top Layers

    The hand penetrometer for top layers is a device that is used to determine the penetration resistance of top layers. Because of the limited overall length of the device, the hand penetrometer can also be used for horizontal measurement, for instance in the walls of profile pits.

  • Eijkelkamp - Model 06.03 - Pocket Penetrometer

    Eijkelkamp - Model 06.03 - Pocket Penetrometer

    The 'pocket penetrometer' is specifically used to determine the penetration resistance of top layers (measuring depth 5 mm) and of samples in the field or in the laboratory. Measuring range 0.5 MPa. When pushing the instrument into the ground, the pin encounters a force of the ground. The spring is compressed by this force. A slip ring is taken along during this operation, which shows on the scale the maximum force that has been encountered. The scale...

  • Model 14.10 - Pocket Vane Tester with 3 Vanes

    Model 14.10 - Pocket Vane Tester with 3 Vanes

    The pocket vane tester is a shear strength measuring tool that is used in profile pits or on the surface. The small, practical format also makes the tool very suitable for testing on soil samples. The short period of time the test takes allows for several measurements in the same soil or layer which in turn allows for the calculation of an average value. The shear strength can be raead from a scale fitted with dragging pointer.

  • Model 14.05 - Field Inspection Vane Tester

    Model 14.05 - Field Inspection Vane Tester

    The shear strength or stress of the soil depends on different soil characteristics such as for instance: the granular composition, the humus content, the humidity and (in case of vegetation covered areas) the degree of coverage and the density of the roots. In order to determine the shear stress in the strata in for instance a profile pit, on the surface (for instance a sports terrain), at the bottom of a bore hole or in a sample, several different...

  • Model 14.08 - Field Inspection Vane Borer

    Model 14.08 - Field Inspection Vane Borer

    Field inspection vane borer, standard set for measurement up to 160 kPa (16 t/m2) and a depth of 10 m. The robust field inspection vane borer is a somewhat heavier tool for measuring the shear strength in the field. Without pre-drilling a hole the vane can be pushed or hammered into the soil. If the soil is too hard, then it is recommended to pre-drill a hole. Measurements can be executed up to a depth of 10 meter and a shear strength can be measured...

  • Hooghoudt - Hydraulic Conductivity Test Kit

    Hooghoudt - Hydraulic Conductivity Test Kit

    In case of direct measurement in the field the auger hole method according to Hooghoudt can be applied.Following this method the determination of the permeability to water of a soil takes little time (by comparison to other methods), requires a limited number of instruments.

  • Ksat - Constant Head Permeameter Set

    Ksat - Constant Head Permeameter Set

    The Ksat constant head permeameter is an instrument that provides the means to collect data for determining in situ saturated hydraulic conductivity of the vadose (unsaturated) zone easily and conveniently. The measuring procedure is known as constant head well permeameter technique, shallow well pump-in method or borehole infiltration test. Before the equipment is used a hole is augered (the bottom of the hole must be plane (use the Riverside auger)....

  • Model 09.06 - Mini Rainfall Simulator for Erosion Test

    Model 09.06 - Mini Rainfall Simulator for Erosion Test

    The extent to which the soil is sensitive to erosion is determined largely by the composition of the soil. Knowledge of the sensitivity to erosion is important for the development of a certain plot. The sensitivity to erosion is hard to measure. Absolute values can not be obtained. It is, however, possible to obtain a reasonable indication by means of a relative measurement. For such a measurement a rainfall simulator can be applied.

  • Model 09.09 - Tension Infiltrometer Set

    Model 09.09 - Tension Infiltrometer Set

    The tension infiltrometer measures the hydraulic properties of unsaturated soil. Water held under tension infiltrates into a dry soil through a highly permeable stainless steel membrane. The time dependent infiltration rate is used to calculate unsaturated hydraulic conductivities and related hydraulic properties. Infiltration rates are recorded manually. With the pressure transducers, which can be connected to a datalogger, the rates can also be read...

  • Model 14.04 - 90 cm Multi-Functional Tensiometers Set

    Model 14.04 - 90 cm Multi-Functional Tensiometers Set

    This multi-functional set can be applied to execute different research with various types of tensiometers up to a depth of 90 cm. The standard tensiometer for example is used in irrigation areas for permanent placement. The Jet-fill tensiometer has an additional water reservoir in order to be able to continuously fill the tensiometer allowing it to be ready for use faster and more mobile.

  • Model SM150 - Soil Moisture Sensor

    Model SM150 - Soil Moisture Sensor

    The soil moisture sensor SM150 is a cost effective sensor for obtaining reasonably accurate soil moisture measurements without compromising robust build quality and long term reliability. The sensor can be read out with the soil moisture meter HH2 (art. 14.26.02) and is compatible with a large variety of loggers (M12 connection, 0 -1 V DC). The sensor is buriable and its cylindrical shape makes it easy to install in augered holes (45 mm diameter). Two...

  • Model 19.33 - W.E.T. Sensor Kit

    Model 19.33 - W.E.T. Sensor Kit

    Also included in our product range is the WET sensor, to measure pore water conductivity and temperature in the top layer of a soil. The measurement values are shown on the display of the hand held meter and can be stored in the memory (including time and sensor location). These data can be read on a PC.

  • Trime-Pico - Model 14.65 - Soil Humidity Measuring System

    Trime-Pico - Model 14.65 - Soil Humidity Measuring System

    The Trime-PICO soil humidity measuring system is a complete solution for measuring and registering soil humidity and temperature. The system makes use of the advanced and accurate Time Domain Reflectrometry technology (TDR). TDR measuring technology measures with greater accuracy than the FD measuring technology and is also suitable for other media than soil (for example substrates or foodstuffs). The system is specially designed for use in the field...

  • Model 14.04.03 - Standard Tensiometer

    Model 14.04.03 - Standard Tensiometer

    The standard tensiometer consists of a clear transparent plastic tube with a ceramic cup at the bottom end and a manometer at the top. The standard tensiometer is delivered in various lengths allowing the execution of simultaneous measurements at various depths in the root zone. For pre-drilling special auger sets can be provided.

  • Model 14.50 - Electronic Tensimeter

    Model 14.50 - Electronic Tensimeter

    The electronic tensimeter is a portable pressure sensor in a bag for measurement of the moisture tension in the soil, measured through a tensiometer tube placed in the soil. The measuring device can be moved from tensiometer tube to tensiometer tube allowing an unlimited number of measurements over a short period of time. The hypodermic needle of the tensimeter is fitted on the tensiometer tube through the silicon stopper after which the moisture...

  • ThetaProbe - Model ML3 - Soil Moisture Measuring Sensor  Set

    ThetaProbe - Model ML3 - Soil Moisture Measuring Sensor Set

    The Thetaprobe (ML3) soil moisture sensor (art. no.: 14.26.07.02) measures the soil moisture volume percentage by applying the Frequency Domain technique. The Thetaprobe measures the soil moisture volume percentage by measuring the changes in the dielectric constant. The changes are converted into a millivolt signal proportional to the soil moisture content. The sensor consists of a sturdy, watertight synthetic housing which contains the electronics....

  • Model 14.22 - Soil Moisture Meter in Case

    Model 14.22 - Soil Moisture Meter in Case

    Soil moisture measuring system with gypsum blocks The soil moisture meter can be used in combination with soil moisture blocks (relatively cheap gypsum blocks). The soil moisture content is determined by measuring the resistance between two electrodes inside the gypsum blocks. The condition for reliable measurements is the optimal contact between sensor and soil.

  • Rhizon - Model 19.21.SA - Soil Moisture Sampling Set

    Rhizon - Model 19.21.SA - Soil Moisture Sampling Set

    With the Rhizon soil moisture sampler we supply a range of miniature soil moisture samplers. The Rhizon samplers are used for repeated and reliable sampling of all dissolved components in the soil solution. The porous plastic material (PES) wets spontaneously and has standard 0.15 micron pores. The samplers are supplied with coextruded tubing (PE inside / PVC outside) 1 mm internal diameter, luer connector and protective cap. The sampler is reenforced...

  • Model 14.36 - Oxygen Diffusion Meter

    Model 14.36 - Oxygen Diffusion Meter

    In plant cultivation it is very important that the soil has proper ventilation. The necessary oxygen supply for the roots and the discharge of the carbon dioxide gas that is formed there, in case of most cultivated growth, takes place via the soil. Also soil chemical processes depend on the presence of oxygen in the soil.

  • Arcadis-Eijkelkamp - Model 20.02 - Oil Detection Pan

    Arcadis-Eijkelkamp - Model 20.02 - Oil Detection Pan

    The oil detection pan is developed for a rapid on-site analysis of soil and groundwater for floating contaminants e.g. soaps, dyestuffs and all kinds of oil derivates such as tar, lubricating oil, kerosine and petrol.

  • Hellige - Model 08.10 - pH-Indicator for Soil

    Hellige - Model 08.10 - pH-Indicator for Soil

    A number of analysis of the soil can be executed immediately in the field. The determination of the pH and the nitrate content are soil analysis that frequently occur. The Hellige pH-indicator is a very simple apparatus to estimate the pH (acidity) of a soil for the purpose of a soil suitability indication and straight forward fertilizing advise. The pH is determined on the basis of colour comparison.

  • Nitratech - Model 18.40 - 5-500 ppm Reflectometer

    Nitratech - Model 18.40 - 5-500 ppm Reflectometer

    The Nitrachek reflectometer is a pocket size digital measuring instrument for a simple and quick determination in the field of the nitrate content in water or in a watery extract of soil or crop. The method is based on read-out of nitrate test strips. After a test strip is held in the solution it is placed in the optical read-out apparatus. The instrument has a memory for up to 20 measuring sets with date/ time indication. The measuring range is 5 -...

  • Eijkelkamp - Model 11.03.30 - Manual Sounding Devices

    Eijkelkamp - Model 11.03.30 - Manual Sounding Devices

    The devices are provided with a probe, which is connected to a measuring tape with centimeter graduation. When the probe touches a conductive liquid, a clear acoustic and light signal is produced. If the cable is then lifted a little, the signal will stop. Determination of this point allows the user to read the depth directly from the measuring tape (accuracy: ± 0.5 cm).

  • Eijkelkamp - Model 14.35 - Soil Oxygen Content Analysis System

    Eijkelkamp - Model 14.35 - Soil Oxygen Content Analysis System

    Soil gas analysis can yield a lot of information concerning the soil environment. Using a ‘piercing probe’ and an oxygen content meter the growing conditions for shrubs and trees can be defined. And who would not want to be able to measure the extent of soil pollution in an area without timeconsuming soil drilling?

  • Water(-Bottom) Sampling Equipment

  • Model 04.23.SA - Sediment Core Sampler Type Beeker

    Model 04.23.SA - Sediment Core Sampler Type Beeker

    (Set A = basic set) can be used as an independent sampler. Like Multisampler / piston sampler but with lockable head and it is possible to hammer the sampler. 1.0 and 1.5 m long sampling tubes. Only suitable for assessing / pressing out samples on site. Operation almost as simple as Multisampler or piston sampler. Much cheaper than the old Beeker sampler set. The standard set is suitable for application in water to a maximum depth of 5 meter. Using...

  • Eijkelkamp - Model 12.25 - Peristaltic Pump

    Eijkelkamp - Model 12.25 - Peristaltic Pump

    This peristaltic pump, specially designed for use in the field, is battery powered and microprocessor controlled. The microprocessor enables an adjustable constant number of revolutions (which can be stored in memory), protection against overload and various modes of external control. Controlling the peristaltic pump can be executed via the key-pad on the front panel. A built-in maintenance free 12 Volt battery enables you to use the pump 2 to 5 hours...

  • Model 12.04.SA - 250 ml Bailer Sampler Set

    Model 12.04.SA - 250 ml Bailer Sampler Set

    This bailer sampler consists of a stainless steel tube and is available in a design with a 33 mm or 45 mm diameter and a content of resp. 250 ml and 1000 ml. The stainless steel tube is open at the top-end and fitted with an unscrewable cap at the bottom. A ball check is fitted in the bottom. As soon as the water sampler is lowered it can be lifted again. To assure a proper replacement of the contents during the lowering, the sampler is lifted half a...

  • Model 12.14 - Motorized Foot Valve Pump Set

    Model 12.14 - Motorized Foot Valve Pump Set

    Among other items the standard set contains a foot valve pump suitable for two pumping tubes, tube guides, ball valves, polyethylene tube and an aluminium tripod. The revolutionary PowerPack PP1, a borehole sampling system for groundwater and leachate, is light enough to be carried by one person. It’s powerful enough to lift water from 50 m depth and is so compact, that it fits onto a back-pack frame. The PowerPack PP1 combines a power source...

  • Eijkelkamp - Model 12.13 - Hand-Operated Foot Valve Pump Set

    Eijkelkamp - Model 12.13 - Hand-Operated Foot Valve Pump Set

    Two tubes, with a diameter of 10 or 16 mm, can be fitted on the hand-operated foot valve pump. The lever hinges on a tripod of which the height can be adjusted. In this way it is possible to take samples from wells fitted with a shaft type well cover as well as street type well covers. The hinge point of the lever can be moved quickly, in this way the stroke lever ratio can be adjusted which makes it possible to work efficiently at all times. The...

  • Sensors & Monitoring

  • Model 11.32.01 - Multiple GPRS Global Data Transmitter

    Model 11.32.01 - Multiple GPRS Global Data Transmitter

    The purpose of the Global Data Transmitter Multiple (GDT-M) of Eijkelkamp is to connect to the e-SENSE sensor product line and Divers and transmit sensor data to our customers anywhere in the world. The Global Data Transmitter (GDT) Multiple is designed for extended use in the field and to transmit data in a secure way. The Global Data Transmitter Multiple GPRS is a modem with 6 ports for e-SENSE sensors and/or Divers. Telemetry via e-mail, incl....

  • Diver - Water Level Logger

    Diver - Water Level Logger

    Diver water level data loggers are the world’s most widely used and compact instruments for automatic measurement and registration of groundwater level, conductivity and temperature.

  • e+ RAIN - Model 11412201 - Metal Rain Gauge

    e+ RAIN - Model 11412201 - Metal Rain Gauge

    Rain gauge e+ RAIN (metal) for heavy conditions, with tipping bucket, 1 pulse per 0.2 mm precipitation, accuracy 2%, surface 400 cm², height 42 cm, incl. heating element 24 Vdc / 250 mA. Cable length 1.5 m with IP68 connector for watertight connection to the e+ RAIN logger. Warranty 2 years.

  • Eijkelkamp - Model 16.99 - 8 Channels Automatic Agro Meteostation

    Eijkelkamp - Model 16.99 - 8 Channels Automatic Agro Meteostation

    Eijkelkamp Soil & Water designed a standard 8 channel meteostation for measuring, recording and processing of the standard parameters: wind speed and wind direction, global radiation, air temperature, air humidity and precipitation. The station is constructed around a foldable mast which can be taken apart, allowing for mobile applications of the station. The datalogger (16.99.15) with built-in air temperature and relative air humidity sensor has...

  • Eijkelkamp - Model e+ SOIL MCT - Conductivity and Temperature Sensor

    Eijkelkamp - Model e+ SOIL MCT - Conductivity and Temperature Sensor

    Eijkelkamp Soil & Water has developed a Soil Moisture, Conductivity and Temperature sensor in it’s e+ sensor product range. Measured data are stored internally and can be transferred optically to the user via the e-SENSE® telemetry system or directly to a handheld readout or PC.

  • Eijkelkamp - Model 13.12 - 125mm Current Meter Synthetic Propeller

    Eijkelkamp - Model 13.12 - 125mm Current Meter Synthetic Propeller

    The instrument is used for the accurate determination of the current velocity in water ways, channels, rivers and the sea. The meter can also be applied in polluted water currents. The measurements are executed with the propeller mounted on the rod(s) or connected to a cable. The current velocity meter has a measuring range of 0.025 to 10 m/sec.

  • Eijkelkamp - Model 13.17.02 - Water discharge Measurements: RBC Flumes

    Eijkelkamp - Model 13.17.02 - Water discharge Measurements: RBC Flumes

    RBC flumes are used to measure the quantity of water that, for instance, flows through an irrigation channel. By comparison to known flumes, such as the WSC-and the Parshall flume, the RBC flume is the most accurate. The RBC flume has been specially designed for use in smaller water ways or earthen channels (irrigation channels, in- outlets, furrow, ditches, etc.). The RBC flumes is a simple and reliable instrument for the measurement of the quantity...

  • Eijkelkamp - Model SAM-1 - Aquameter

    Eijkelkamp - Model SAM-1 - Aquameter

    The SAM-1 Smart Aquameter turns your smartphone or tablet into a powerful and convenient pH, redox or conductivity and temperature meter. Simply connect the SAM-1 and smart sensor into the audio jack of your smartphone or tablet and you are ready to take accurate readings. Compatible with Apple and Android smartphones and tablets.

  • AquaPlus - Model DO and EC- 18.53 - Optical Measuring Set

    AquaPlus - Model DO and EC- 18.53 - Optical Measuring Set

    The AquaPlus probe is a combined optical dissolved oxygen, electrical conductivity and temperature sensor. Thanks to the built in conductivity sensor, the AquaPlus is able to calculate and automatically compensate DO readings for changes in water salinity.

  • AquaLogger - Model 2000 - 2 Bore Holes for Remote Data Logging

    AquaLogger - Model 2000 - 2 Bore Holes for Remote Data Logging

    The AquaLogger-2000 is designed to fit down 2” bore holes for remote data logging. The unit features programmable event triggers to increase logging rate if rapid changes occur. The supplied LoggerLink software enables logger configuration (data file and memory management, setting measuring intervals and event trigger configuration). Data can be exported as text report or excel spreadsheet.

  • AquaLogger - Model 7000- 18.59.50 - Down Bore Holes for Remote Data Logging

    AquaLogger - Model 7000- 18.59.50 - Down Bore Holes for Remote Data Logging

    The AquaLogger-7000 is designed to fit down bore holes for remote data logging. The AquaLogger-7000 is designed to be used outdoors and is rated to IP67, that is to say it is waterproof but it is not designed for submersion. The unit features programmable event triggers to increase logging rate if rapid changes occur. The supplied LoggerLink software enables logger configuration (data file and memory management, setting measuring intervals and event...

  • TD-Diver - Model 11110402 - 10 m Water Level Logger

    TD-Diver - Model 11110402 - 10 m Water Level Logger

    The new TD-Diver water level logger is a totally new design which combines over 75 years of groundwater monitoring experience with the most recent technologies and components available in the market today. The TD-Diver is based on an ingenious and proven concept and is acknowledged as the most reliable instrument for the autonomous measuring and recording of groundwater level and temperature. Its internal working memory of 72,000 measurements per...

  • Model GDT-S Prime - GPRS Set for Eijkelkamp SIM

    Model GDT-S Prime - GPRS Set for Eijkelkamp SIM

    GDT-S Prime GPRS set for Eijkelkamp Soil & Water SIM card, consisting of GDT-S Prime (113401), inclusive alkaline battery D 1.5 V set of 2 pieces (113121), GPRS/UMTS antenna (113434) and installation check (113411); exclusive price SIM card subscription (116281/82) and once-only connection costs SIM card (116280). Warranty 2 years.

  • Eijkelkamp - Model GDT-S Prime - GPRS set for Custom SIM

    Eijkelkamp - Model GDT-S Prime - GPRS set for Custom SIM

    GDT-S Prime GPRS set for customer specific SIM card, consisting of GDT-S Prime GPRS (113401), inclusive alkaline battery D 1.5 V, set of 2 pieces (113121) and GPRS/UMTS antenna (113434); exclusive installation check (113411). Warranty 2 years.

  • Eijkelkamp - Model GDT-S Prime - GPRS Set without SIM

    Eijkelkamp - Model GDT-S Prime - GPRS Set without SIM

    GDT-S Prime GPRS set without SIM card, consisting of GDT-S Prime GPRS (113401), inclusive alkaline battery D 1.5 V, set of 2 pieces (113121) and GPRS/UMTS antenna (113434); exclusive installation check (113411). Warranty 2 years.

  • Data Logger

  • Cera-Diver - Water Level Data Logger

    Cera-Diver - Water Level Data Logger

    Robust and durable water level logger with corrosion proof housing. Perfect long term solution for saline environments. Housing is corrosion proof, robust and durable. Available in various measuring ranges.

  • CTD-Diver - Water Level Data Logger

    CTD-Diver - Water Level Data Logger

    Corrosion Proof Multi-parameter Groundwater Datalogger. Durable and robust water level and datalogger. Housing is corrosion proof . Conductivity range of 0 to 120 mS/cm . Long-term solution for monitoring saline environments . Available in various measuring ranges.

  • Laboratory Equipment

  • Eijkelkamp - Model 08.01 - Sandbox for pF-Determination

    Eijkelkamp - Model 08.01 - Sandbox for pF-Determination

    The standard set for pF-determination pF 0 - 2.0 (0 - 0.1 bar) consists of the sandbox with control panel, suction levelling stand, water supply bottle with stand, filter cloth (140-150 micron), a number of containers synthetic sand, grain size approximately 73 micron and various accessories.

  • Eijkelkamp - Model 08.65 - Air Permeameter for Soil

    Eijkelkamp - Model 08.65 - Air Permeameter for Soil

    The air permeameter apparatus measures the permeability or conductance of an (undisturbed) soil sample. Air permeability is the property of the soil pore system allowing air to flow through. Generally the pore sizes and their connectivity determine whether a soil has high or low permeability. Air will flow easily through soil with large pores and good connectivity between them. Small pores with the same degree of connectivity would have lower...

  • Eijkelkamp - Model 08.30 - Hydrometer Kit

    Eijkelkamp - Model 08.30 - Hydrometer Kit

    To obtain an accurate determination of the particle size distribution of the smallest fractions it is possible to apply the hydrometer method. In this method the sample is cleaned from organic matter after which it is dried and weighed. Next it is suspended in water and sieved. The solution that passes through the sieve is transferred to a measuring cylinder with water. Hydrometer readings are taken after regular intervals. Sedimentation time and...

  • Eijkelkamp - Model 08.53 - Calcimeter

    Eijkelkamp - Model 08.53 - Calcimeter

    The calcimeter by Eijkelkamp Soil & Water is suitable for the simultaneous determination of the carbonate content in 5 samples. Where possible the vulnerable glass was replaced by synthetic materials. Because hydrochloric acid is used a stable and ergonomic design was chosen. The calcimeter is delivered complete with reaction vessels and test tubes (without reagents).

  • Eijkelkamp - Model 08.16.SA / 08.16.SB - Table Model Pipette Apparatus

    Eijkelkamp - Model 08.16.SA / 08.16.SB - Table Model Pipette Apparatus

    The particle-size distribution is one of the most important physical qualities of a soil. The division of soils (soil classification) is primarily based on particle-size distribution. When accurately determining the particle size in samples, in addition to the determination using sieves, other methods will need to be applied. A simple method for the determination of the particle size is the pipette method. After carbonates, organic substances and...

  • Consumables

  • Direct-well - Model 10.04.30 - 36 mm Miniature Monitoring System

    Direct-well - Model 10.04.30 - 36 mm Miniature Monitoring System

    The Direct-well is a miniature monitoring system. Bentonite collars are slipped over the tubing, which causes the room between the tubing and the impermeable layer to be sealed. Due to its materials, the Direct-well system is suited for researching groundwater on all micro and macro parameters.

Products by Delta-T Devices Ltd.

  • Soil Science - Soil Moisture

  • Delta-T - Model PR2 - Soil Moisture Profile Probe

    Delta-T - Model PR2 - Soil Moisture Profile Probe

    No other soil moisture probe system enables you to monitor your soil water profiles with such ease and flexibility. Install an access tube into the soil, insert the PR2 Profile Probe and press the HH2 [Read] button to display an instantaneous reading, or connect the PR2 to a data logger (GP2, DL6 or DL2e) and leave the system to record soil moisture changes over time. The PR2 soil moisture probe is built around patented sensing technology which...

  • Delta-T - Model Auger PR2 - Access Tubes

    Delta-T - Model Auger PR2 - Access Tubes

    Augering and Extraction Kits for optimal Access Tube installation. Profile Probes are used within access tubes inserted into augered holes in the soil - correct installation is vital for accurate measurement of soil moisture profiles. The goal of installation is to produce optimal contact between the soil and the wall of the access tube. The augered holes should be straight, smooth sided and the correct diameter. Delta-T augering kits help...

  • Delta-T - Model SM150T - Soil Moisture and Temperature Sensor

    Delta-T - Model SM150T - Soil Moisture and Temperature Sensor

    ***New Sensor for 2017*** Dependable ± 3% soil moisture accuracy - Built in temperature measurement - Robust and buriable, with 5 year warranty. The SM150T measures soil moisture and temperature with research-grade accuracy. It offers stable, robust and reliable performance at a great price. The SM150T’s advanced patented electronics and tough build produce a highly dependable sensor with exceptional salinity and temperature stability. The SM150T...

  • Delta-T - Model ML3 ThetaProbe - Soil Moisture and Temperature Sensor

    Delta-T - Model ML3 ThetaProbe - Soil Moisture and Temperature Sensor

    The new ThetaProbe adds temperature measurement to its class‐leading soil moisture measurement capabilities. The ML3 ThetaProbe makes it easy to take reliable, accurate soil moisture measurements. Simply insert the probe into the soil, connect your data logger or meter, provide 5‐14V DC at 18mA, and within seconds you can be measuring soil moisture. The ThetaProbe’s class‐leading ± 1% accuracy, stability and reliability...

  • Delta-T - Model PR2 SDI-12 - Profile Probe

    Delta-T - Model PR2 SDI-12 - Profile Probe

    The PR2 SDI-12 is a new digital alternative to the well-established analogue PR2 Profile Probe. It shares the many strengths of the analogue PR2 soil moisture probe, but with the addition of SDI-12 compatibility - allowing integration into new and existing SDI-12 systems.

  • Soil Science - Soil Water Potential

  • Delta-T - Model EQ3 - Equitensiometer

    Delta-T - Model EQ3 - Equitensiometer

    The EQ3 uses class leading ThetaProbe technology to avoid the many problems of water-filled tensiometers. It measures water potential (matric potential) in the range 0 to -1000 kPa and provides an accurate loggable output. It is particularly well suited for use in dry soils.

  • Soil Science - Meters and Loggers

  • Delta-T - Model GP2 - Advanced Data Logger

    Delta-T - Model GP2 - Advanced Data Logger

    The GP2 Data Logger is ideal for demanding research applications and field work. It is weatherproof, rugged, battery powered and comes with 12 differential analogue inputs and 2 relays as standard. It can log most sensor types and accepts SDI-12, voltage, resistance, current, potentiometer, bridge, counter, frequency, and digital state inputs.

  • Delta-T - Model HH2 - Moisture Meter - Readout Unit

    Delta-T - Model HH2 - Moisture Meter - Readout Unit

    The Moisture Meter type HH2 is a versatile readout unit for use with Delta-T Devices soil moisture sensors: the Profile Probe, ThetaProbe, SM300, SM150 and WET Sensor. The HH2 readout unit offers impressive functionality in a compact, hand-held unit, designed for field use. Readings are displayed on the LCD and can be stored to memory for later download to a PC.

  • Meteorology and Solar - Solar Radiation

  • Delta-T - Model SPN1 - Sunshine Pyranometer

    Delta-T - Model SPN1 - Sunshine Pyranometer

    SPN1 Sunshine Pyranometer, Global (Total) and Diffuse irradiance in W.m-2, WMO sunshine threshold: 120 W.m-2 direct beam, No moving parts, shade rings or motorised tracking, No routine adjustment or polar alignment, Works at any latitude, Precision ground glass dome.

  • Delta-T - Model BF5 - Sunshine Sensor

    Delta-T - Model BF5 - Sunshine Sensor

    The BF5 Sunshine Sensor is a versatile, multi-purpose solar radiation sensor. It uses an array of photodiodes with a unique computer-generated shading pattern to measure incident solar radiation. A microprocessor calculates the global and diffuse components of the radiation and determines the sunshine state. The BF5 Sunshine Sensor is protected by patents EP 1012633 and US 6417500. Two analogue voltage outputs give global and diffuse radiation, from...

  • Meteorology and Solar - Weather Stations

  • Delta-T - Model WS-GP1 - Compact Weather Station

    Delta-T - Model WS-GP1 - Compact Weather Station

    The WS-GP1 Automatic Weather Station includes high grade sensors to measure rain, solar radiation, wind speed, wind direction, relative humidity and air temperature. The system comes complete with the GP1 Data Logger and a 2m tripod mast.

  • Delta-T - Model WS-GP2 - Advanced Automatic Weather Station System

    Delta-T - Model WS-GP2 - Advanced Automatic Weather Station System

    The advanced WS-GP2 Automatic Weather Station is based on the powerful GP2 Data Logger. It is an ideal solution for research and environmental monitoring applications at remote and exposed sites. The WS-GP2 provides a highly rugged and flexible system – users can select the optimal combination of sensors, logger, power and communications.

  • Meteorology and Solar - Other Sensors