Eijkelkamp Soil & Water

33 products found

Products

  • Augering & Soil Sampling Equipment

  • Eijkelkamp - Model 01.11.SE - Ergonomic Hand Auger Set for Heterogeneous Soils - 5 M

    Eijkelkamp - Model 01.11.SE - Ergonomic Hand Auger Set for Heterogeneous Soils - 5 M

    The ergonomic hand auger set for heterogeneous soils is used to carry out manual drilling and sampling in a great variety of different soils in an ergonomically sound way. It is particularly suitable for general soil investigation (description of the layering, geology, archaeology) as well as taking samples for such activities as environmental research. It can carry out drillings to a depth of 5 metres, depending on the depth of the groundwater, the...

  • Model 04.16 - Soil Coring Kit for Chemical Soil Research

    Model 04.16 - Soil Coring Kit for Chemical Soil Research

    Soil sampling for the determination of the presence of very volatile components such as benzene, toluene, xylene and  chlorinated hydrocarbons should be executed with samplers that prevent the sample from being exposed to air. Preferably the sampling must be done without disturbance of the soilaggregates to prevent mixing with air.

  • Model HM1812, RD32 - Percussion Drilling Set Hammer for Heterogeneous Soils

    Model HM1812, RD32 - Percussion Drilling Set Hammer for Heterogeneous Soils

    With the percussion drilling set for heterogeneous soils with heavy electrical percussion hammer (HM 1812), the percussion gouges are hammered into the soil using an electrically driven percussion hammer with 72.8 Joule strike capability. The advantages of this hammer are: no petrol vapours and exhaust gasses directly over the sample. The set contains: an electrically driven percussion hammer with accessories, an aggregate (continuous power 3.4 kVa),...

  • Model 04.02.SA - Bi-Partite Gouge Auger Set, to 5 M, Bay

    Model 04.02.SA - Bi-Partite Gouge Auger Set, to 5 M, Bay

    Hand-operated equipment can be applied for soil research up to a depth of 5 to 10 meter. The gouge augers have a mutual quality, they are all fitted with an almost half cylindrical operational part with parallel cutting edges running vertically, justifying the name gouge auger. This operational part may vary in length as well as in diameter. The most suitable length depends on the penetration resistance, the substance of the soil and the required...

  • Eijkelkamp - Model Cobra TT - Percussion Drilling Set for Heterogeneous Soils

    Eijkelkamp - Model Cobra TT - Percussion Drilling Set for Heterogeneous Soils

    The Eijkelkamp percussion drilling set for heterogeneous soils with gasoline powered percussion hammer (Cobra TT), is standard equipped for drilling to a depth up to 5 meter. The complete set contains: a gasoline driven percussion hammer with accessories and wooden transport box, various extension rods, coupling sleeves, percussion gouges (combination type for various types of soil) in various diameters and lengths, a core sampler for PVC sample tubes...

  • Metha - Model 04.10.SA - Compact, Multifunctional Corer for Taking Soil Samples

    Metha - Model 04.10.SA - Compact, Multifunctional Corer for Taking Soil Samples

    A compact, multifunctional corer for taking soil samples (possibly containing volatiles). The 16-ml (about 25 g) soil samples are cut from above the ground surface. They can then be packed so that they are protected from sorption (without synthetic materials), leakage and diffusion, and are then refrigerated or frozen. Analysis subsequently takes place within 48 hours or two weeks. The methanol conservation method can also be used. An ejector presses...

  • Eijkelkamp - Model 04.09 - Stainless Steel Peat Sampler

    Eijkelkamp - Model 04.09 - Stainless Steel Peat Sampler

    The stainless steel peat sampler is in fact a kind of gouge auger. The peat sampler is pushed into the soil manually. The sample containing part is a half cylinder. The peat sampler distinguishes itself from the standard gouge auger as its cone is massive. The sample containing section is sealed off by a plate (fin) that can pivot around the axle in the middle of the sampler and that is fitted with a cutting edge on one side. Having arrived at the...

  • Eijkelkamp Akkerman - Core Sampler Set

    Eijkelkamp Akkerman - Core Sampler Set

    Using the Akkerman core sampler, samples are taken in stainless steel sampling tubes in auger holes or casing tubes (above as well as under the groundwater level, casing tubes with minimal diameter 100 mm) up to a maximum depth of 50 m. The Akkerman core sampler is used in combination with a tripod and hand winch. The sampling tube is beaten into the soil using a falling hammer. After sampling the sampling tube can be sealed off with the PE covers. A...

  • Wardenaar - Model 05.09 - Peat Profile Sampler

    Wardenaar - Model 05.09 - Peat Profile Sampler

    Until recently, sampling undisturbed peat profiles in peat lands, was a very difficult activity. Digging and sampling profile pits in most peat lands is difficult (if not impossible) as they would immediately fill with water and the walls would slump.

  • Eijkelkamp - Model 05.08 - 10 x 5 cm, 50 cm Profile Soil Sampler

    Eijkelkamp - Model 05.08 - 10 x 5 cm, 50 cm Profile Soil Sampler

    The profile sampler allows taking of a sizeable and virtually undisturbed sample up to a depth of approximately 40 cm (10 cm wide and 5 cm across). All roots, up to a cross-section of 2 cm, are included in the sample. When sampling, both U-shaped gutters are pushed alternatingly into the soil, until the required depth is reached, after which one side of the handle is pulled sharply upwards and the other pushed downwards, thus clamping the profile. The...

  • Model 04.17 - Split Tube Sampler Ø 53 mm, Set

    Model 04.17 - Split Tube Sampler Ø 53 mm, Set

    The split tube sampler is an apparatus for rapid undisturbed sampling at the surface. The apparatus is very suitable for research on root systems, fertilizing and soil biology. The set consists of a split tube sampler with a handle with beating head, hammer with nylon heads (shock-absorbing), sample liners, storage containers and a steel lifting jack with lever and chain. The split tube sampler consists of two stainless steel tube halves with a...

  • Model 99.14 - Fieldcart, Aluminium, Collapsible, 15kg

    Model 99.14 - Fieldcart, Aluminium, Collapsible, 15kg

    You are also fully-mobile in the field with the collapsible fieldcart. The sturdy aluminium construction makes the fieldcart (with inflatable tires) very suitable for carrying all kinds of equipment in the field to a maximum loading weight of 150 kg. The cart is suited to transport packages with dimensions 120 x 56 cm. The cart, when folded (107 x 27 x 58 cm), takes up very little room, weighs only 15 kg and can be easily transported in a station...

  • Model 04.18.07.01 - Mechanical Rod Puller, 1-Man Operated

    Model 04.18.07.01 - Mechanical Rod Puller, 1-Man Operated

    Without too much effort the gouges can be extracted from the soil by using rod pullers, which can be provided in different designs. The first gouge can easily be extracted using a rod puller fitted with a rod puller extension system (art. no. 04.18.07.05). If the gouge still is partially stuck in the top soil, then it can be removed using a lifting jack (art. no. 05.07.03) with lever and chain (art. no. 05.07.14). In case of the other (deeper) gouges,...

  • Model 04.19.43.01 - Foil Insertion Kit for Core Sampler

    Model 04.19.43.01 - Foil Insertion Kit for Core Sampler

    A set which you can use the core sampler of the percussion drilling set with a thin PE foil liner. Over the years there where some remarks/complaints about the fact that it was a very difficult and elaborate job to get the sample out of the tube. This was only possible either by cutting or sawing. With the new system this transparent synthetic sampling tube is replaced by a long plastic foil.

  • Model Ø 63mm, RD32, 100cm - Core Sampler

    Model Ø 63mm, RD32, 100cm - Core Sampler

    In addition to ordinary percussion gouges it is possible to apply a core sampler with a synthetic sampling tube or foil liners. These are transparent to facilitate immediate visual inspection in the field. The special cutting head has been fitted with an exchangeable core catcher in order to avoid loss of sample or sample contamination. The undisturbed sample can be sealed for transport to a laboratory.

  • Eijkelkamp - Model 01.11.SO - Auger Set for Heterogeneous Soils

    Eijkelkamp - Model 01.11.SO - Auger Set for Heterogeneous Soils

    01.11.SO. Augerings and samplings in homegeneous soils (soils with an uniform soil profile), in almost all cases can be executed with one type of auger. For augerings in heterogeneous soils (soils with a layered soil profile), several different auger types will be applied. This has led to the composition of an auger set for heterogeneous soils. With the standard set it is possible to execute manual augering to a depth of 5 meter, without great...

  • Eijkelkamp - Model 04.06 - Gouge Auger Set for Top Layers

    Eijkelkamp - Model 04.06 - Gouge Auger Set for Top Layers

    A correctly dosed fertilization is a condition for high yield and good quality. From economic and ecological perspectives it is therefore necessary to check the state of the soil. After analysis of the samples taken with this set it is possible to determine a fertilization program. Two gouge augers have been included in the set for sampling top layers.

  • Model E - Heavy 53 mm Sample Ring Kit

    Model E - Heavy 53 mm Sample Ring Kit

    Sample ring kit model E, with heavy duty sample ring holder for sampling in hard soils. Standard set for a depth of 2 m. For soil sample rings Ø 53 mm.

  • Eijkelkamp - Model 01.12.16.10.B - Batch Sampler Ø 10 cm

    Eijkelkamp - Model 01.12.16.10.B - Batch Sampler Ø 10 cm

    Sampling during batch inspection and sand dredging. Sampling loose discharged sand, dry coarse sand and fine gravel is a special job. Sampling according an imaginary grid, standing on top of the discharged material is not easy.

  • Eijkelkamp - Model 15.20 - Water Well Test Set

    Eijkelkamp - Model 15.20 - Water Well Test Set

    When a promising aquifer has been found, a pump  test lasting one hour and some simple water quality checks must be performed. This procedure greatly reduces the risk of a low yield and/or unsatisfactory water quality after construction. For this purpose one can use the set. The test set in fact belongs to the surveying set (15.01.SA) and provides sufficient information upon which to base decisions as to wether or not the aquifer can supply...

  • Model Ø 23 mm - Grass Plot Sampler Small

    Model Ø 23 mm - Grass Plot Sampler Small

    These stainless steel gouge augers with different dimensions consist of a steel auger pipe, a collecting bucket and a stick with a steel handle. The auger pipe is filled by pressing the collecting bucket with your foot. Because of the conical shape of this pipe the sample is easily pushed toward the collecting trough when the next sample is taken. The correct number of samples per hectare depends, among other factors, on the type of crop, the relief...

  • Eijkelkamp - Model 04.04 - Gouge Auger Set for Stepwise Sampling

    Eijkelkamp - Model 04.04 - Gouge Auger Set for Stepwise Sampling

    Hand-operated equipment can be applied for soil research up to a depth of 5 to 10 meter. In this product information leaflet a number of gouge augers are described. Their mutual quality is that they are all fitted with an almost half cylindrical operational part with parallel cutting edges running vertically, justifying the name gouge auger. This operational part may vary in length as well as in diameter. The most suitable length depends on the...

  • Eijkelkamp - Model 04.01.SA - Single Gouge Auger Set, Standard, 1 m

    Eijkelkamp - Model 04.01.SA - Single Gouge Auger Set, Standard, 1 m

    Hand-operated equipment can be applied for soil research up to a depth of 5 to 10 meter. In this product information leaflet a number of gouge augers are described. Their mutual quality is that they are all fitted with an almost half cylindrical operational part with parallel cutting edges running vertically, justifying the name gouge auger. This operational part may vary in length as well as in diameter. The most suitable length depends on the...

  • Eijkelkamp - Model 02.01.01 - Aluminium Tripod, Cap 6.5 kN (650 kgf)

    Eijkelkamp - Model 02.01.01 - Aluminium Tripod, Cap 6.5 kN (650 kgf)

    A tripod is an essential part of a bailer boring set (cable tool drilling equipment). Also drillings at greater depths, or the application of heavier augering or soil core sample equipment require the use of a tripod. In selecting a tripod, working height, weight, and maximum load capacity (= tensile force) are usually determinant factors. However, the range of application is of such a magnitude, that the selection of the tripod depends strongly on...

  • Eijkelkamp - Model 15.09 - Standard Heavy Lifting Set

    Eijkelkamp - Model 15.09 - Standard Heavy Lifting Set

    The heavy lifting set is usually used in combination with heavier (hand-operated) drilling equipment for water wells. The tripod and the winch are used, among other things, for lowering and lifting drilling equipment (e.g. the bailer), or for removing the casing tubes.