30 products found
J.K.F. Industri A/S Products
-
Filters and Separators
JKF has a large and extensive filter programme within bag and cartridge filters. Our filter programme ranges from extraction from a single machine using a portable vacuum cleaner to traditional modular filter solutions and advanced filter solutions with round, welded filters and SuperBlower filters. A filter consists basically of an inlet section, a filter section, a cleaning system and a discharge section.
-
JKF SuperBlower - Under and Over-pressure Filter
The SuperBlower filter is an under- and over-pressure filter designed to run in constant operation. Constructed as a self-supporting sheet metal construction in high tensile steel modules. Process air is passed into a filter chamber, where the larger particles settle to the bottom of the filter, from where the air is passed through filter bags which retain the residual particles. The modular SuperBlower filter is a flexible design which can be adapted to ...
-
JKF DustStorm - Under and Over-pressure Filter
The DustStorm filter is an under- and over-pressure filter, designed for continuous operation. Constructed as a self-supporting sheet metal construction. The round design ensures great strength combined with low ...
-
JKF - Modular Dust Filters
JKF’s modular dust filters are bag filters. Modular filters can have up to 30 single or double modules, and with various discharge systems: silo, blow through, bag emptying, rotary valve, screw or chain. They are made of 1.25 and 2 mm galvanised sheet metal. The standard filter medium is PE40/PE25 bags. The filters are available with different bag lengths, depending on ...
-
JKF - Model Type PL and PLD - Silo Filter
Silo filter type PL and PLD is a bag filter. The filter is used on a flat silo top so that the contaminated air flows directly against the underside of the bag bottom and up through the bags for ...
-
JKF - Model Type L-LD - Blow Through Filter
Blow through filter types L and LD are bag filters. They are used for extraction from minor applications, max. 4 HDL modules. The filter has automatic emptying. Emptying is achieved using a secondary fan which extracts the material. The secondary fan represents a suction force of approx. 25% of the primary fan's air ...
-
JKF - Model Type JK-S/JK-EXS - Rotary Valve
Rotary valves type JK-S/JK-EXS are fitted with a 6-bladed rotor with hard-wearing rubber blades bolted to the rotor shaft plate ...
-
JKF - Model Type JK-PS - Separator
Type JK-PS separators are designed to separate solids from carrier air in over- or under-pressure systems. The separator design ensures low pressure loss and unpressurised material separation, making it possible to install the separator directly connected to other equipment, such as compressors and containers. They are able to separate particles greater than 3 mm, but the max. size is governed by the dimensions of the rotor chamber. Rotor blades are ...
-
JKF - Model Type JK-2 JC and JK-3 JC - Cutters
Type JK-2 JC and JK-3 JC cutters are designed for continuous cutting of plastic and paper strips in cut or endless rolls from edge cutters and roller cutter machines. The cutter chops strips into small pieces, which are easier to transport than long strips, ensuring smooth transport to a collection point or ...
-
JKF - Combination Valve
Combination valve helps reduce extraction plant energy consumption. The valve is fitted after the filter clean air discharge. Return air from the filter can either be fed back to the production area or outdoors via the combination ...
-
JKF - Filter Media
JKF can supply filters for most industry sectors where manufacturing processes generate dust, chips and dirt to be extracted and filtered. Examples: Woodworking, Iron and metal industries, Surface treatment, Sandblasting, Corn, seed and feeds, Cement and concrete, Power generation, Insulation manufacturing, Packaging manufacturing, Recycling ...
-
JKF - Model Type CS - Spiral Cyclones
Spiral cyclones type CS are used for air treatment plants in the wood and paper industries and for corn and feed to separate chaff and corn dust in exhaust air from drying and cleaning plants. They are made of rolled and riveted hot-dip galvanised sheet metal, but can be supplied in welded 2 - 3 mm sheet. Type CS-20 is painted in RAL 5010. Cleaning door in cone is an optional ...
-
JKF - Model Type JA - Spiral Cyclones
Cyclone type JA is intended for separation of fine grain particles in transport and dust extraction plants. Cyclones are designed for high efficiency. Powder coating corrosion class C3. Legs are non-standard, but available as optional extras. Cleaning door in cone is an optional ...
-
JKF - Big-bag Solution
The big-bag solution is a complete solution with a big-bag rack, rotor valve, screw conveyor and the connection to the individual filters. It is provided with filling stub with protection against unintended access to rotating ...
-
JKF - Dust Bucket
The dust bucket is suitable for all Blower, EC and DustStorm filters with the exception of DS-7. The dust bucket is mobile and ergonomic correctly designed. The handle can be locked in 2 positions. When the handle is locked in the upper position, the tank can easily be moved. When the handle is locked in the lower position, the tank is easily turned upside down for emptying. Mounting of the bag can easily and quickly be carried out and without any risk ...
-
JKF - Explosion Duct Valves
The explosion duct valve is used in order to prevent that an explosion in the plant will be channelled back to the production premises and machines. The explosion duct valve is mounted on the duct section between the plant and the source of dust. The explosion duct valve stops explosions that occur in the opposite direction of the normal flow. This means that the explosion duct valve is mounted on the inlet side on the dust separator, never on the outlet ...
-
Fan Systems
Resistance occurs in all forms of air transport due to friction which means that overall pressure is reduced in the flow direction. To effect and maintain air transport, pressure has to be increased at some stage to compensate for pressure loss. This is usually achieved in fan systems using radial and axial fans designed to boost air in the direction of the outlet. A fan’s effect is always based on the actual volume flow through the inlet. If the volume flow is indicated at a temperature different than that of the fan in a given operating situation, it must be corrected. Motors and fans are usually supplied as a unit. JKF has designed its fans for optimal performance, and it is vital to select the right one for any given task. The speed at which the fan is to run can be seen from the graph for that fan. The power input depends on resistance in the system.
-
JKF - Model Type JK-20 - 40D - Direct Drive Centrifugal Fan
The direct drive centrifugal fan types JK-20D - JK-40D are designed for material handling. Equipped with self-cleaning impellers with backward-inclined blades and aerodynamic intake. The impellers are statically and dynamically balanced. Max. operating temperature: 60°C. Number of blades are reduced by 2 for paper impeller. Number of blades are reduced by 2 for paper impeller. Available in anti-spark version with stainless steel inlet and ...
-
JKF - Model Type T-200D/K - T-500D/K - Indirect Driven Centrifugal Fan
The indirect driven centrifugal fan types T-200K – T-500K and direct driven fan types T-200D – T-500D is designed for concentrated material handling over long distances. The impellers are available in 2 versions, an open T-impeller for coarse-grained or rather long material types and a closed P-impeller for dust particles (< 2 mm). The impeller for paper is always made as open T-impeller with 6 blades. T-impeller is available in ...
-
JKF - Model JK-HT - High - Pressure Fans
The JK-HT high-pressure fans are one-step centrifugal fans with sealed impellers. They are designed for transport of granular material with a density of between 0.2 and 1.2 ...
-
JKF - Injectors and Feeder Units
The injectors are designed for mounting on high-pressure fan types JK-2HT, JK-4HT, JK-5HT and ...
-
Duct Systems
JKF`s wide range of ducts includes galvanised duct systems and welded duct systems in 2 and 3 mm material thickness, and thus represents the basic element in extraction and transport of particles and air.
-
JKF - Laser Welded and Longitudinally Lock Formed Ducts
Laser welded and longitudinally lock formed ducts are galvanised and made from 0.75 mm, 0.90 mm or 1.00 mm sheet metal (s). Ducts are also available in 1.25 mm sheet metal. Also available in other qualities and dimensions to order. Ducts of up to ø400 mm diameter are supplied as standard laser welded in lengths of 0.5 m, 1.0 m and 2.0 m. Other sizes from ø450 mm diameter are supplied as longitudinally lock formed ducts in standard lengths of ...
-
JKF - Ducts Systems - 2 and 3 mm
Diameter for 2 mm: ø80 - ø1250 mm. 2 and 3 mm ducts D < 600 mm supplied as standard for pull rings [f.b]. Ducts with D = ø630 mm - ø1250 mm supplied with flanges ...
-
JKF - Model JK-6 - Duct System
The JK-6" duct system is specially designed for fast installation and tight, smooth assemblies. Assembly method is rapid lock pull rings. The special design facilitates high transport capacity and with minimum risk. The rolled ends of the JK-6" system provide strength and minimise the risk of transport ...
-
Duct Systems in Stainless Steel
-
JKF - Stainless Steel Laser Welded Ducts
Diameter: ø80 - ø1000 mm. Laser welded ducts are made of 0.70 mm sheet metal. Longitudinally lock formed ducts are made of0,80 mm sheet metal. Ducts are supplied in 0.5 m, 1.0 m and 2.0 m ...
-
JKF - Stainless Steel Telescopic Ducts
Diameter: ø100 - ø500 mm. Telescopic ducts are made of 0.80 mm sheet metal, and supplied with rapid lock pull ring, including rubber insert. Rapid lock pull rings are ...
-
JKF - Stainless Steel Pull Rings
Stainless steel pull rings [f.b] are in two pieces. EPDM rubber rings are available as optional extras for sealing of diameter assemblies ø80 - ø500 mm. Supplied in plastic bags of 10 pcs. Each bag also contains the nuts and bolts required for the ...
-
JKF - Stainless Steel Flanges
Diameter: ø80 - ø400 mm. Flanges are made in accordance with JKF’s standard, and are a standard component in the product range. Flanges are made in EN 1.4301 (AISI 304) stainless ...
-
JKF - Stainless Steel Jet Caps
Diameter: ø120 - ø400 mm. Jet caps are supplied with the same assembly methods as duct systems. They are fitted with an internal cone and drain hose for disposal of ...
-
JKF - Stainless Steel Ducts with Access Door
Diameter: ø80 - ø1000 mm. Access doors are made of 0.80 mm and 1.00 mm sheet metal such that the inside is smooth and has a close ...
-
JKF - Stainless Steel Ducts with Cleaning Spigot
Diameter: ø100 - ø400 mm. PVC lid is easy to put on and take off. All cleaning spigots have a ø100 mm ...
-
High-pressure Extraction
JKF’s product programme for high pressure extraction is built up as a flexible system. It gives the possibility of individual building up and adjustment and contributes to ensure the right solution regardless industry. JKF is stocking all components, and you are therefore guaranteed a supply here and now.
-
JKF - Flap Valves
Flap value with conical entry for inserting into the ...