SDEC France

SDEC France

362 products found

products

  • Lysimeters

  • Model SPS 200 - Soil Solution Sampling System

    Model SPS 200 - Soil Solution Sampling System

    Groundwater pollution is now a well known problem around the world. The danger occurs when polluting molecules leach through the soil and into a water sheet supplying a drinkable water tank. The SPS 200 soil solution sampling system is a simple equipment built to help environmental scientists study the movements of molecules in the soil. It can extract water coming out of cultivated soils or any other type of soil. The principle on which the SPS 200...

  • Model SW 070 series - Stainless Steel Suction Lysimeters

    Model SW 070 series - Stainless Steel Suction Lysimeters

    Suction cells collect pore water out of unsaturated soil. A constant vacuum source draws pore water into the cell through a porous stainless stell membrane. Pore water samples are brought to the surface by applying vacuum or pressure. Suction cells are most suitable in moist soil (tension less than 500 mbar) and can also be used below the water table. The collected soil solution isn't contaminated by elements contained in the system. Thus, it can be...

  • Environmental Monitoring

  • SDEC - Model PMS 9000 - Unpolarizable Electrodes Probe Derives

    SDEC - Model PMS 9000 - Unpolarizable Electrodes Probe Derives

    This probe derives directly out of the geophysical field. It is new in the AGRONOMICAL and ENVIRONMENTAL research but has been used for 25 years in geophysics with great success. The transfert of this technology allows to use it now in AGRONOMY to study hydric transferts in soils by measuring the self-potentials in these soils. The PMS 9000 is a reliable probe which can last for about 15 years. These great advantages allow you to use this probe in...

  • Soil Tensiometers

  • SDEC - Model SKT 850 - Side Electronic Pressure Sensor

    SDEC - Model SKT 850 - Side Electronic Pressure Sensor

    The SKT 850 pressure sensor is built for field use and has a 0 to -999 HPa (mbar) measuring range. The SKT 850 sensor has its own temperature correction (-10°C /+50°C). The sensor is light (60 grs) and small. The SKT 850 sensor is compact, waterproof and is built for outdoor as well as indoor use. The SKT 850 sensor will be strongly fixed to any tensiometer. The SKT 850 sensor exists in two versions : differential voltage or current loop...

Products by Eijkelkamp Soil & Water

  • Augering & Soil Sampling Equipment

  • Eijkelkamp - Model 01.11.SE - Ergonomic Hand Auger Set for Heterogeneous Soils - 5 M

    Eijkelkamp - Model 01.11.SE - Ergonomic Hand Auger Set for Heterogeneous Soils - 5 M

    The ergonomic hand auger set for heterogeneous soils is used to carry out manual drilling and sampling in a great variety of different soils in an ergonomically sound way. It is particularly suitable for general soil investigation (description of the layering, geology, archaeology) as well as taking samples for such activities as environmental research. It can carry out drillings to a depth of 5 metres, depending on the depth of the groundwater, the...

  • Model 04.16 - Soil Coring Kit for Chemical Soil Research

    Model 04.16 - Soil Coring Kit for Chemical Soil Research

    Soil sampling for the determination of the presence of very volatile components such as benzene, toluene, xylene and  chlorinated hydrocarbons should be executed with samplers that prevent the sample from being exposed to air. Preferably the sampling must be done without disturbance of the soilaggregates to prevent mixing with air.

  • Model HM1812, RD32 - Percussion Drilling Set Hammer for Heterogeneous Soils

    Model HM1812, RD32 - Percussion Drilling Set Hammer for Heterogeneous Soils

    With the percussion drilling set for heterogeneous soils with heavy electrical percussion hammer (HM 1812), the percussion gouges are hammered into the soil using an electrically driven percussion hammer with 72.8 Joule strike capability. The advantages of this hammer are: no petrol vapours and exhaust gasses directly over the sample. The set contains: an electrically driven percussion hammer with accessories, an aggregate (continuous power 3.4 kVa),...

  • Model 04.02.SA - Bi-Partite Gouge Auger Set, to 5 M, Bay

    Model 04.02.SA - Bi-Partite Gouge Auger Set, to 5 M, Bay

    Hand-operated equipment can be applied for soil research up to a depth of 5 to 10 meter. The gouge augers have a mutual quality, they are all fitted with an almost half cylindrical operational part with parallel cutting edges running vertically, justifying the name gouge auger. This operational part may vary in length as well as in diameter. The most suitable length depends on the penetration resistance, the substance of the soil and the required...

  • Eijkelkamp - Model Cobra TT - Percussion Drilling Set for Heterogeneous Soils

    Eijkelkamp - Model Cobra TT - Percussion Drilling Set for Heterogeneous Soils

    The Eijkelkamp percussion drilling set for heterogeneous soils with gasoline powered percussion hammer (Cobra TT), is standard equipped for drilling to a depth up to 5 meter. The complete set contains: a gasoline driven percussion hammer with accessories and wooden transport box, various extension rods, coupling sleeves, percussion gouges (combination type for various types of soil) in various diameters and lengths, a core sampler for PVC sample tubes...

  • Metha - Model 04.10.SA - Compact, Multifunctional Corer for Taking Soil Samples

    Metha - Model 04.10.SA - Compact, Multifunctional Corer for Taking Soil Samples

    A compact, multifunctional corer for taking soil samples (possibly containing volatiles). The 16-ml (about 25 g) soil samples are cut from above the ground surface. They can then be packed so that they are protected from sorption (without synthetic materials), leakage and diffusion, and are then refrigerated or frozen. Analysis subsequently takes place within 48 hours or two weeks. The methanol conservation method can also be used. An ejector presses...

  • Eijkelkamp - Model 04.09 - Stainless Steel Peat Sampler

    Eijkelkamp - Model 04.09 - Stainless Steel Peat Sampler

    The stainless steel peat sampler is in fact a kind of gouge auger. The peat sampler is pushed into the soil manually. The sample containing part is a half cylinder. The peat sampler distinguishes itself from the standard gouge auger as its cone is massive. The sample containing section is sealed off by a plate (fin) that can pivot around the axle in the middle of the sampler and that is fitted with a cutting edge on one side. Having arrived at the...

  • Eijkelkamp Akkerman - Core Sampler Set

    Eijkelkamp Akkerman - Core Sampler Set

    Using the Akkerman core sampler, samples are taken in stainless steel sampling tubes in auger holes or casing tubes (above as well as under the groundwater level, casing tubes with minimal diameter 100 mm) up to a maximum depth of 50 m. The Akkerman core sampler is used in combination with a tripod and hand winch. The sampling tube is beaten into the soil using a falling hammer. After sampling the sampling tube can be sealed off with the PE covers. A...

  • Wardenaar - Model 05.09 - Peat Profile Sampler

    Wardenaar - Model 05.09 - Peat Profile Sampler

    Until recently, sampling undisturbed peat profiles in peat lands, was a very difficult activity. Digging and sampling profile pits in most peat lands is difficult (if not impossible) as they would immediately fill with water and the walls would slump.

  • Eijkelkamp - Model 05.08 - 10 x 5 cm, 50 cm Profile Soil Sampler

    Eijkelkamp - Model 05.08 - 10 x 5 cm, 50 cm Profile Soil Sampler

    The profile sampler allows taking of a sizeable and virtually undisturbed sample up to a depth of approximately 40 cm (10 cm wide and 5 cm across). All roots, up to a cross-section of 2 cm, are included in the sample. When sampling, both U-shaped gutters are pushed alternatingly into the soil, until the required depth is reached, after which one side of the handle is pulled sharply upwards and the other pushed downwards, thus clamping the profile. The...

  • Model 04.17 - Split Tube Sampler Ø 53 mm, Set

    Model 04.17 - Split Tube Sampler Ø 53 mm, Set

    The split tube sampler is an apparatus for rapid undisturbed sampling at the surface. The apparatus is very suitable for research on root systems, fertilizing and soil biology. The set consists of a split tube sampler with a handle with beating head, hammer with nylon heads (shock-absorbing), sample liners, storage containers and a steel lifting jack with lever and chain. The split tube sampler consists of two stainless steel tube halves with a...

  • Model 99.14 - Fieldcart, Aluminium, Collapsible, 15kg

    Model 99.14 - Fieldcart, Aluminium, Collapsible, 15kg

    You are also fully-mobile in the field with the collapsible fieldcart. The sturdy aluminium construction makes the fieldcart (with inflatable tires) very suitable for carrying all kinds of equipment in the field to a maximum loading weight of 150 kg. The cart is suited to transport packages with dimensions 120 x 56 cm. The cart, when folded (107 x 27 x 58 cm), takes up very little room, weighs only 15 kg and can be easily transported in a station...

  • Model 04.18.07.01 - Mechanical Rod Puller, 1-Man Operated

    Model 04.18.07.01 - Mechanical Rod Puller, 1-Man Operated

    Without too much effort the gouges can be extracted from the soil by using rod pullers, which can be provided in different designs. The first gouge can easily be extracted using a rod puller fitted with a rod puller extension system (art. no. 04.18.07.05). If the gouge still is partially stuck in the top soil, then it can be removed using a lifting jack (art. no. 05.07.03) with lever and chain (art. no. 05.07.14). In case of the other (deeper) gouges,...

  • Model 04.19.43.01 - Foil Insertion Kit for Core Sampler

    Model 04.19.43.01 - Foil Insertion Kit for Core Sampler

    A set which you can use the core sampler of the percussion drilling set with a thin PE foil liner. Over the years there where some remarks/complaints about the fact that it was a very difficult and elaborate job to get the sample out of the tube. This was only possible either by cutting or sawing. With the new system this transparent synthetic sampling tube is replaced by a long plastic foil.

  • Model Ø 63mm, RD32, 100cm - Core Sampler

    Model Ø 63mm, RD32, 100cm - Core Sampler

    In addition to ordinary percussion gouges it is possible to apply a core sampler with a synthetic sampling tube or foil liners. These are transparent to facilitate immediate visual inspection in the field. The special cutting head has been fitted with an exchangeable core catcher in order to avoid loss of sample or sample contamination. The undisturbed sample can be sealed for transport to a laboratory.

  • Eijkelkamp - Model 01.11.SO - Auger Set for Heterogeneous Soils

    Eijkelkamp - Model 01.11.SO - Auger Set for Heterogeneous Soils

    01.11.SO. Augerings and samplings in homegeneous soils (soils with an uniform soil profile), in almost all cases can be executed with one type of auger. For augerings in heterogeneous soils (soils with a layered soil profile), several different auger types will be applied. This has led to the composition of an auger set for heterogeneous soils. With the standard set it is possible to execute manual augering to a depth of 5 meter, without great...

  • Eijkelkamp - Model 04.06 - Gouge Auger Set for Top Layers

    Eijkelkamp - Model 04.06 - Gouge Auger Set for Top Layers

    A correctly dosed fertilization is a condition for high yield and good quality. From economic and ecological perspectives it is therefore necessary to check the state of the soil. After analysis of the samples taken with this set it is possible to determine a fertilization program. Two gouge augers have been included in the set for sampling top layers.

  • Model E - Heavy 53 mm Sample Ring Kit

    Model E - Heavy 53 mm Sample Ring Kit

    Sample ring kit model E, with heavy duty sample ring holder for sampling in hard soils. Standard set for a depth of 2 m. For soil sample rings Ø 53 mm.

  • Eijkelkamp - Model 01.12.16.10.B - Batch Sampler Ø 10 cm

    Eijkelkamp - Model 01.12.16.10.B - Batch Sampler Ø 10 cm

    Sampling during batch inspection and sand dredging. Sampling loose discharged sand, dry coarse sand and fine gravel is a special job. Sampling according an imaginary grid, standing on top of the discharged material is not easy.

  • Eijkelkamp - Model 15.20 - Water Well Test Set

    Eijkelkamp - Model 15.20 - Water Well Test Set

    When a promising aquifer has been found, a pump  test lasting one hour and some simple water quality checks must be performed. This procedure greatly reduces the risk of a low yield and/or unsatisfactory water quality after construction. For this purpose one can use the set. The test set in fact belongs to the surveying set (15.01.SA) and provides sufficient information upon which to base decisions as to wether or not the aquifer can supply...

  • Model Ø 23 mm - Grass Plot Sampler Small

    Model Ø 23 mm - Grass Plot Sampler Small

    These stainless steel gouge augers with different dimensions consist of a steel auger pipe, a collecting bucket and a stick with a steel handle. The auger pipe is filled by pressing the collecting bucket with your foot. Because of the conical shape of this pipe the sample is easily pushed toward the collecting trough when the next sample is taken. The correct number of samples per hectare depends, among other factors, on the type of crop, the relief...

  • Eijkelkamp - Model 04.04 - Gouge Auger Set for Stepwise Sampling

    Eijkelkamp - Model 04.04 - Gouge Auger Set for Stepwise Sampling

    Hand-operated equipment can be applied for soil research up to a depth of 5 to 10 meter. In this product information leaflet a number of gouge augers are described. Their mutual quality is that they are all fitted with an almost half cylindrical operational part with parallel cutting edges running vertically, justifying the name gouge auger. This operational part may vary in length as well as in diameter. The most suitable length depends on the...

  • Eijkelkamp - Model 04.01.SA - Single Gouge Auger Set, Standard, 1 m

    Eijkelkamp - Model 04.01.SA - Single Gouge Auger Set, Standard, 1 m

    Hand-operated equipment can be applied for soil research up to a depth of 5 to 10 meter. In this product information leaflet a number of gouge augers are described. Their mutual quality is that they are all fitted with an almost half cylindrical operational part with parallel cutting edges running vertically, justifying the name gouge auger. This operational part may vary in length as well as in diameter. The most suitable length depends on the...

  • Eijkelkamp - Model 02.01.01 - Aluminium Tripod, Cap 6.5 kN (650 kgf)

    Eijkelkamp - Model 02.01.01 - Aluminium Tripod, Cap 6.5 kN (650 kgf)

    A tripod is an essential part of a bailer boring set (cable tool drilling equipment). Also drillings at greater depths, or the application of heavier augering or soil core sample equipment require the use of a tripod. In selecting a tripod, working height, weight, and maximum load capacity (= tensile force) are usually determinant factors. However, the range of application is of such a magnitude, that the selection of the tripod depends strongly on...

  • Eijkelkamp - Model 15.09 - Standard Heavy Lifting Set

    Eijkelkamp - Model 15.09 - Standard Heavy Lifting Set

    The heavy lifting set is usually used in combination with heavier (hand-operated) drilling equipment for water wells. The tripod and the winch are used, among other things, for lowering and lifting drilling equipment (e.g. the bailer), or for removing the casing tubes.

  • Laboratory Equipment

  • Eijkelkamp - Model 08.01 - Sandbox for pF-Determination

    Eijkelkamp - Model 08.01 - Sandbox for pF-Determination

    The standard set for pF-determination pF 0 - 2.0 (0 - 0.1 bar) consists of the sandbox with control panel, suction levelling stand, water supply bottle with stand, filter cloth (140-150 micron), a number of containers synthetic sand, grain size approximately 73 micron and various accessories.

  • Eijkelkamp - Model 09.02.01.05 - Laboratory Permeameter Open System, 5 Holders

    Eijkelkamp - Model 09.02.01.05 - Laboratory Permeameter Open System, 5 Holders

    In principle it is possible to design the soil water permeameters in any required size. The size is determined by the number of soil samples of which the saturated water permeability is to be determined simultaneously. Designs for 5 up to 25 soil sample rings can be supplied. The permeameters are available for soil sample rings with an external diameter of 53 or 60 mm.

  • Eijkelkamp - Model 08.53 - Calcimeter to Determine Carbonate

    Eijkelkamp - Model 08.53 - Calcimeter to Determine Carbonate

    The calcimeter by Eijkelkamp Soil & Water is suitable for the simultaneous determination of the carbonate content in 5 samples. Where possible the vulnerable glass was replaced by synthetic materials. Because hydrochloric acid is used a stable and ergonomic design was chosen. The calcimeter is delivered complete with reaction vessels and test tubes (without reagents). Per reaction approximately one hour is required. Carbonates that are hard to...

  • Eijkelkamp - Model 08.30 - Hydrometer Kit - Standard Set

    Eijkelkamp - Model 08.30 - Hydrometer Kit - Standard Set

    Hydrometer kit, standard set. Maximum number of samples 6. Measuring range 0.995 - 1.035 g/ml and -5 - 60 g/l. Power supply line voltage. Reading accuracy 1 g/l. Sample specification disturbed. Package size 120 x 80 x 64 cm. Voltage 230 volt. Weight 59 kg.

  • Eijkelkamp - Model 08.65 - Air Permeameter for Soil

    Eijkelkamp - Model 08.65 - Air Permeameter for Soil

    The air permeameter apparatus measures the permeability or conductance of an (undisturbed) soil sample. Air permeability is the property of the soil pore system allowing air to flow through. Generally the pore sizes and their connectivity determine whether a soil has high or low permeability. Air will flow easily through soil with large pores and good connectivity between them. Small pores with the same degree of connectivity would have lower...

  • Eijkelkamp - Model 08.66 - Surface Shear Test Apparatus, Set

    Eijkelkamp - Model 08.66 - Surface Shear Test Apparatus, Set

    In many land use systems worldwide soil deformation is a major problem arising from increasing land use intensity. Altered soil functions, in particular reduced hydraulic conductivities and impeded aeration, influence the top soil layers. This has an important effect on vulnerability to erosion, in particular. Assessing very thin soil layers like soil crusts requires very sensitive and highly accurate equipment which should also allow very small...

  • Eijkelkamp - Model 08.67 - Compression Test Apparatus Set

    Eijkelkamp - Model 08.67 - Compression Test Apparatus Set

    In many land use systems all over the world soil deformation is a major problem due to increasing land use intensity. On arable soils machine traffic is continuously intensified with respect to load and wheeling frequency leading to (sub-)soil compaction and deeper soil degradation concerning hydrologic or pneumatic functions. Altered soil functions, in particular reduced hydraulic conductivities end impeded aeration, may decrease crop growth and...

  • Eijkelkamp - Model 08.68 - Shear Test/Compression Apparatus

    Eijkelkamp - Model 08.68 - Shear Test/Compression Apparatus

    The shear test apparatus (art. no. 08.68) measures the shear stress of an undisturbed soil sample. During the measurement soil water matrix, compression stress and vertical displacement are simultaneously measured. The shear test apparatus is operating computer controlled using multifunctional software for executing measurement protocols and visualised data presentation. The samples are taken in a soil sample ring Ø 103 x 100 mm, height 30 mm,...

  • Eijkelkamp - Model 08.16.SA / 08.16.SB - Table Model Pipette Apparatus

    Eijkelkamp - Model 08.16.SA / 08.16.SB - Table Model Pipette Apparatus

    The particle-size distribution is one of the most important physical qualities of a soil. The division of soils (soil classification) is primarily based on particle-size distribution. When accurately determining the particle size in samples, in addition to the determination using sieves, other methods will need to be applied. A simple method for the determination of the particle size is the pipette method. After carbonates, organic substances and...

  • Eijkelkamp - Model 08.60 - Air Pycnometer According to Langer

    Eijkelkamp - Model 08.60 - Air Pycnometer According to Langer

    The air pycnometer is supplied as a complete set, including a calibration block. The apparatus is suited for sample rings with a maximum diameter of 53 or 60 mm (max. height 51 resp. 40 mm). The instrument has a measuring range of 0-115 cm3. The time period of the measurement is approximately 1 minute. The maximum measuring accuracy equals 1%.

  • Eijkelkamp - Model 080213 - Suction Level Control System

    Eijkelkamp - Model 080213 - Suction Level Control System

    Suction level control system (electronical), pressure range 0...-600 hPa, incl. integrated control panel, pressure sensor and 10 l tank. Power supply 110 - 230 Vac (47/63 Hz) / 24 Vdc. With CE-approved. For use with article 080212.

  • Eijkelkamp - Model AS200 - Electromagnetic Sieve Shaker

    Eijkelkamp - Model AS200 - Electromagnetic Sieve Shaker

    Electromagnetic sieve shaker, to accept maximal 8 sieves (50 mm height) with Ø of 200 mm 230V-50Hz. Time controlled operation 1-99 min. Vibration height adjustable 0-3 mm with visuable control. Inclusive clamping cover (200 mm) for dry sieving.

  • Eijkelkamp - Model 10000, 14000, 17000 rpm - Soil Stirring Device

    Eijkelkamp - Model 10000, 14000, 17000 rpm - Soil Stirring Device

    Soil stirring device for the mixing of soil/water solutions using an electrically powered fourpart blade, 230 V - 50 Hz. The number of rotations can be set either on 10.000, 14.000 or 17.000 rotations per minute. The apparatus is fitted with an automatic start/stop function. The engine is placed in a rubber support reducing noise and vibrations to a minimum. The soil stirring apparatus is supplied inclusive a mixing beaker with a...

  • Sensors & Monitoring

  • Eijkelkamp - Model Spectral-8  UV/Vis - Spectrometer

    Eijkelkamp - Model Spectral-8 UV/Vis - Spectrometer

    Real-time optical measurement of BOD, COD, TOC, NO3 and many others: Whether for process control, compliance monitoring or early warning of quality issues, up to date water quality information is critical. It is therefore surprising that the most common solution remains the collection of grab samples, which provides intermittent information and with substantial delay. The alternative, bringing the lab to the field using wet chemical analysers, comes...

  • Eijkelkamp - Model AP-2000-D - Multiparameter Package

    Eijkelkamp - Model AP-2000-D - Multiparameter Package

    Multiparameter AP-2000-D set, consisting of GPS Aquameter, Aquaprobe AP-2000-D with DO (optical), EC, pH, Redox, Sal, depth and temperature and 2 extra ports for optional sensors (ISE or optical), with 3 meter cable, accessories and fluids in rugged case.

  • TD-Diver - Model 11110402 - 10 m Water Level Logger

    TD-Diver - Model 11110402 - 10 m Water Level Logger

    Water level logger type TD-Diver for measuring and recording groundwater levels/temperatures. Range 10 m, -20 till +80 °C. Memory 72000 measurements (and 72000 backup). Dimensions 22 x 110 mm. Pressure sensor: ceramic. Housing: stainless steel 316L. Accuracy 0.05%/10 m, + 0,1 °C, temperature compensation 0/+40 °C. Warranty 1 years.

  • TD-Diver - Model 11110404 - 20 m Water Level Logger

    TD-Diver - Model 11110404 - 20 m Water Level Logger

    Water level logger type TD-Diver for measuring and recording groundwater levels/temperatures. Range 20 m, -20 till +80 °C. Memory 72000 measurements (and 72000 backup). Dimensions 22 x 110 mm. Pressure sensor: ceramic. Housing: stainless steel 316L. Accuracy 0.05%/20 m, + 0,1 °C, temperature compensation 0/+40 °C. Warranty 1 year.

  • TD-Diver - Model 11110406 - 50 m Water Level Logger

    TD-Diver - Model 11110406 - 50 m Water Level Logger

    Water level logger type TD-Diver for measuring and recording groundwater levels/temperatures. Range 50 m, -20 till +80 °C. Memory 72000 measurements (and 72000 backup). Dimensions 22 x 110 mm. Pressure sensor: ceramic. Housing: stainless steel 316L. Accuracy 0.05%/50 m, + 0,1 °C, temperature compensation 0/+40 °C. Warranty 1 year.

  • TD-Diver - Model 11110408 - 100 m Water Level Logger

    TD-Diver - Model 11110408 - 100 m Water Level Logger

    Water level logger type TD-Diver for measuring and recording groundwater levels/temperatures. Range 100 m, -20 till +80 °C. Memory 72000 measurements (and 72000 backup). Dimensions 22 x 110 mm. Pressure sensor: ceramic. Housing: stainless steel 316L. Accuracy 0.05%/100 m, + 0,1 °C, temperature compensation 0/+40 °C. Warranty 1 year.

  • Eijkelkamp - Model Type Micro-Diver, 10 m - Monitoring Well Datalogger

    Eijkelkamp - Model Type Micro-Diver, 10 m - Monitoring Well Datalogger

    Monitoring well datalogger type Micro-Diver for measuring and recording groundwater levels/temperatures. Range 10 m, -20 till +80 °C. Memory 48000 measurements. Dimensions 18 x 90 mm. Pressure sensor: ceramic. Housing: stainless steel 316L. Accuracy 0.15%/10 m, +0,1 °C, temperature compensated 0/+40 °C. Warranty 1 years.

  • Eijkelkamp - Model Micro-Diver, 20 m - Monitoring Well Datalogger

    Eijkelkamp - Model Micro-Diver, 20 m - Monitoring Well Datalogger

    Monitoring well datalogger type Micro-Diver for measuring and recording groundwater levels/temperatures. Range 20 m, -20 till +80 °C. Memory 48000 measurements. Dimensions 18 x 90 mm. Pressure sensor: ceramic. Housing: stainless steel 316L. Accuracy 0.15%/20 m, + 0,1 °C, temperature compensated 0/+40 °C. Warranty 1 years.

  • Baro-Diver - Water Level Logger

    Baro-Diver - Water Level Logger

    The conveniently priced Baro-Diver water level logger has also been equipped with the new technologies. The Baro-Diver ensures that you accurately capture changes in atmospheric pressure. Conveniently priced and easy to deploy, one Baro-Diver covers a radius of up to 15 km, depending on the topography. The Baro-Diver can also be used for measuring shallow water levels up to approximately 0.9 meter. The Baro-Diver has an internal working memory capable...

  • Aquaprobe - Model AP-7000 - Multiparameter Water Quality Probe

    Aquaprobe - Model AP-7000 - Multiparameter Water Quality Probe

    The AP-7000 Aquaprobe is designed for long term deployment utilising a central cleaning system to keep the fitted sensors clean reducing the effects of bio-fouling common in extended deployments. The multiparameter AP-7000 set, consists of a GPS Aquameter, AP-7000 probe DO (optical), EC, pH, Redox, Sal, TDS, depth, temperature and 6 ports for optional sensors (ISE or optical), with 3 meter cable, accessories and fluids. The Aquameter (art. no....

  • Model 11.32.01 - Multiple GPRS Global Data Transmitter

    Model 11.32.01 - Multiple GPRS Global Data Transmitter

    The purpose of the Global Data Transmitter Multiple (GDT-M) of Eijkelkamp is to connect to the e-SENSE sensor product line and Divers and transmit sensor data to our customers anywhere in the world. The Global Data Transmitter (GDT) Multiple is designed for extended use in the field and to transmit data in a secure way. The Global Data Transmitter Multiple GPRS is a modem with 6 ports for e-SENSE sensors and/or Divers. Telemetry via e-mail, incl....

  • Trime-Pico - Model 14.65 - Soil Humidity Measuring System

    Trime-Pico - Model 14.65 - Soil Humidity Measuring System

    The Trime-PICO soil humidity measuring system is a complete solution for measuring and registering soil humidity and temperature. The system makes use of the advanced and accurate Time Domain Reflectrometry technology (TDR). TDR measuring technology measures with greater accuracy than the FD measuring technology and is also suitable for other media than soil (for example substrates or foodstuffs). The system is specially designed for use in the field...

  • Eijkelkamp - Model 13.17.02 - Water Discharge Measurements: RBC Flumes

    Eijkelkamp - Model 13.17.02 - Water Discharge Measurements: RBC Flumes

    RBC flumes are used to measure the quantity of water that, for instance, flows through an irrigation channel. By comparison to known flumes, such as the WSC-and the Parshall flume, the RBC flume is the most accurate. The RBC flume has been specially designed for use in smaller water ways or earthen channels (irrigation channels, in- outlets, furrow, ditches, etc.). The RBC flumes is a simple and reliable instrument for the measurement of the quantity...

  • Eijkelkamp - Model Tensior 4 - Electronic Pressure Transducer

    Eijkelkamp - Model Tensior 4 - Electronic Pressure Transducer

    In case of the Tensior 4 the transducer is located at the bottom end of the tensiometer tube allowing it to be used also in case of frost (frost not too deep into the soil). The pressure transducer can simply be combined with another length of tensiometer tube. This allows measurement at various depths. The Tensior 4 can be used for measurements in different positions. The Tensior 4 has a measuring range of -1000 till +850 hPa and an output signal of...

  • Diver - Water Level Data Logger

    Diver - Water Level Data Logger

    Diver water level data loggers are the world’s most widely used and compact instruments for automatic measurement and registration of groundwater level, conductivity and temperature.

  • Eijkelkamp - Model 16.98.47 - Aerodynamic Rain Gauge

    Eijkelkamp - Model 16.98.47 - Aerodynamic Rain Gauge

    Rain gauge, UV resis. plastic, length 5m. Rain gauge made from UV resistant plastic, aero- dynamic design, with tipping bucket, 1 pulse per 0.2 mm precipitation, accuracy 1%, surface 507 cm2, height 34 cm, cable length 5 m without connector, inclusive calibration certificate.

  • Eijkelkamp - Model A100R - Wind Speed Sensor, Length 5m

    Eijkelkamp - Model A100R - Wind Speed Sensor, Length 5m

    Wind speed sensor A100R (Vector) with calibration certificate, measuring range 0.25 - 75 m/s, accuracy 1% = 0.1 m/s, resolution 1 pulse per 1.25 m wind path, operating temperature range -30 to +55 °C, cable length 5 m.

  • Eijkelkamp - Model 13.12 - 125mm Current Meter Synthetic Propeller

    Eijkelkamp - Model 13.12 - 125mm Current Meter Synthetic Propeller

    The instrument is used for the accurate determination of the current velocity in water ways, channels, rivers and the sea. The meter can also be applied in polluted water currents. The measurements are executed with the propeller mounted on the rod(s) or connected to a cable. The current velocity meter has a measuring range of 0.025 to 10 m/sec.

  • AquaLogger - Model 2000 - 2 Boreholes for Remote Data Logging

    AquaLogger - Model 2000 - 2 Boreholes for Remote Data Logging

    The AquaLogger-2000 is designed to fit down 2” bore holes for remote data logging. The unit features programmable event triggers to increase logging rate if rapid changes occur. The supplied LoggerLink software enables logger configuration (data file and memory management, setting measuring intervals and event trigger configuration). Data can be exported as text report or excel spreadsheet.

  • AquaLogger - Model 7000- 18.59.50 - Down Boreholes for Remote Data Logging

    AquaLogger - Model 7000- 18.59.50 - Down Boreholes for Remote Data Logging

    The AquaLogger-7000 is designed to fit down bore holes for remote data logging. The AquaLogger-7000 is designed to be used outdoors and is rated to IP67, that is to say it is waterproof but it is not designed for submersion. The unit features programmable event triggers to increase logging rate if rapid changes occur. The supplied LoggerLink software enables logger configuration (data file and memory management, setting measuring intervals and event...

  • Eijkelkamp - Model GDT-S Prime - GPRS set for Custom SIM

    Eijkelkamp - Model GDT-S Prime - GPRS set for Custom SIM

    GDT-S Prime GPRS set for customer specific SIM card, consisting of GDT-S Prime GPRS (113401), inclusive alkaline battery D 1.5 V, set of 2 pieces (113121) and GPRS/UMTS antenna (113434); exclusive installation check (113411). Warranty 2 years.

  • Eijkelkamp - Model GDT-S Prime - GPRS Set without SIM

    Eijkelkamp - Model GDT-S Prime - GPRS Set without SIM

    GDT-S Prime GPRS set without SIM card, consisting of GDT-S Prime GPRS (113401), inclusive alkaline battery D 1.5 V, set of 2 pieces (113121) and GPRS/UMTS antenna (113434); exclusive installation check (113411). Warranty 2 years.

  • Eijkelkamp - Model WS-GP2 - Meteo Station With Data Logger

    Eijkelkamp - Model WS-GP2 - Meteo Station With Data Logger

    Meteo station with GP2 data logger for measurement and registration of precipitation, solar radiation, wind speed & direction, soil temperature, rel. humidity and air tempera- ture. Incl. 2 m mast with cross arm, logger canopy and mounting material.

  • Diver-Office - Diver Water Level Logger

    Diver-Office - Diver Water Level Logger

    Start, stop, read and program Diver water level loggers. Exports data to a spreadsheet or modelling program. Diver-Office is flexible ‘project-based' measurement software. Intuitive user interface. Calibrates CTD-Diver water level loggers. Barometric compensation. Units: metric - imperial. Available in 7 languages: English, German, Polish, Portuguese, Spanish, French and Dutch.

  • AquaLogger - Model 2000 - Multiparameter Water Quality Logger

    AquaLogger - Model 2000 - Multiparameter Water Quality Logger

    The AquaLogger-2000 is designed to fit down 2” bore holes for remote data logging. The unit features programmable event triggers to increase logging rate if rapid changes occur. The supplied LoggerLink software enables logger configuration (data file and memory management, setting measuring intervals and event trigger configuration). Data can be exported as text report or excel spreadsheet.

  • Eijkelkamp - Model GDT-S Prime Plus - For Transmitting Sensor Data

    Eijkelkamp - Model GDT-S Prime Plus - For Transmitting Sensor Data

    Connect your sensors, like a water level logger and water quality probe, to our new GDT-S Prime Plus and transmit sensor data to anywhere in the world. Our GDT-S Prime Plus modem is designed for extended use in the field and to send water level, temperature, conductivity, rainfall, soil moisture and various water quality data in a secure way.