UVS Pty Ltd

117 products found

Products by Aanderaa Data Instruments - a Xylem brand

  • Other

  • AADI SmartGuard - Data Logger

    AADI SmartGuard - Data Logger

    The next generation sensor and instrument HUB for Ocean, Lake, Reservoir, Estuary and River Hydrometric stations. Monitoring water and weather  conditions is essential in many operations and the SmartGuard node is well suited for stand-alone stations powered by battery and solar power utilizing wireless real-time data communication. Designed for ease of integration of new and existing sensor technologies into a single Aanderaa observatory node...

  • AADI - Model RCM Blue - Self-recording Dedicated Current Meter

    AADI - Model RCM Blue - Self-recording Dedicated Current Meter

    A new self-recording dedicated current meter with Bluetooth for communications and data retrieval. The RCM Blue is a self-recording Current Meter which also measures water temperature in salt or fresh water, and a battery container with battery capacity up to 70Ah. The Doppler Current Sensor is an upgraded version of the proven SeaGuard ZPulse sensor. The instrument configuration and data retrieval is done via Bluetooth which eliminates the need to...

  • Aquaculture - Environmental Monitoring

  • AADI - Model DB 4700 - Data Buoy

    AADI - Model DB 4700 - Data Buoy

    Data Buoy DB 4700 is a unique Data Collecting System for Met/Ocean Parameters. The Buoy can accommodate a selection of sensors depending on customer’s request. Each Data Buoy is delivered as an Aanderaa Engineering solution to benefit the customer requirements.

  • Construction - Scales for Wheel Loaders and Excavators

  • AADI - Model Loadtronic 3  - Dynamic Weighing System for Wheel Loaders

    AADI - Model Loadtronic 3 - Dynamic Weighing System for Wheel Loaders

    Modern wheel loaders are designed for increased productivity under all conditions. It is important not to lose these properties after installing a weighing system. The Loadtronic 3 weighing system will never tell you to slow down, even on rough surfaces. It helps your company save time and money and increases your profit. This is possible because the Loadtronic 3 has the built-in dynamics system. Drive as you normally do, move fast and flexible....

  • LOADTRONIC 3E - Excavator Scale

    LOADTRONIC 3E - Excavator Scale

    The dynamic weighing system for mono boom excavators. The weighing system is based on the LOADTRONIC wheel loader scale which has been on the market for more than 20 years.

  • Conductivity Sensors

  • Model 4319 - Conductivity Sensor

    Model 4319 - Conductivity Sensor

    A compact fully integrated sensor for measuring the electrical conductivity of seawater. It is designed to be used with SEAGUARD® datalogger using AiCaP CANbus or as standalone sensor using RS-232.

  • Model 4019  - Conductivity Sensor

    Model 4019 - Conductivity Sensor

    A compact fully integrated sensor for measuring the electrical conductivity of seawater. Designed to be mounted on the Recording Doppler Current Profiler RDCP 600. Two versions of this sensor are available, 4019B has enhanced accuracy compared to 4019A, see specifications overleaf.

  • Model 3919/4119/4120 D344 - Conductivity Sensor

    Model 3919/4119/4120 D344 - Conductivity Sensor

    Conductivity Sensor 3919 Conductivity/Temperature Sensor 4119 Conductivity Sensor with analog output 4120 are compact fully integrated sensors for measuring the electrical conductivity of seawater. The 3919 model is designed to be mounted directly on the top-end plate of RCM9/11 and RDCP as well as for stand alone operation via the SR10 or RS-232 interface. The 4119 model can be connected via cable to a AADI SR10/VR22 Data logger, and the 4120 model...

  • Doppler Current Sensor (DCS)

  • Model 4100/4100R - Doppler Current Sensor

    Model 4100/4100R - Doppler Current Sensor

    A rugged, true vector averaging sensor for measuring current speed and direction in the sea. 4100 model: SR10 output for AADI dataloggers 4100R model: RS232 output for third party dataloggers.

  • Oxygen Optodes

  • Model 3835/4130/4175 - Oxygen Optodes

    Model 3835/4130/4175 - Oxygen Optodes

    Oxygen Sensor 3835 Oxygen/Temperature Sensor 4130 Oxygen Sensor w/analog output 4175 are compact fully integrated sensors for measuring the O2-concentration. The 3835 model is designed to be mounted directly on the top-end plate of RCM-9 or RDCP as well as for stand alone operation using SR10 or RS-232 interface. The 4130 model can be connected via cable to AADI SR10/VR22 Data logger, and the 4175 model provides analog output to third party data...

  • Model 3830/3930/3975 - Oxygen Optodes

    Model 3830/3930/3975 - Oxygen Optodes

    Oxygen Sensor 3830 Oxygen/Temperature Sensor 3930 Oxygen Sensor w/analog output 3975 are compact fully integrated sensors for measuring the O2-concentration. The 3830 model is designed to be mounted directly on the top-end plate of RCM-9/11 or RDCP as well as for stand alone operation using SR10 or RS-232 interface. The 3930 model can be connected via cable to AADI SR10/VR22 Data logger, and the 3975 model provides analog output to third party data...

  • Pressure Sensors

  • Pressure Sensor 4017

    Pressure Sensor 4017

    Pressure Sensor 4017 is a compact fully integrated sensor for measuring the pressure level and the water temperature. The sensor is designed to be mounted directly on the top-end plate of RCM 9/11,RDCP or via cable to AADI Data logger using SR10. The sensor can also be used as stand alone sensor using RS-232. The sensor is easily integrated in other measurement systems with third party data loggers.

  • Pressure Sensor 4117

    Pressure Sensor 4117

    Pressure Sensor 4117 is a compact fully integrated sensor for measuring the pressure level and the water temperature. The sensor is designed to be mounted on the AADI SEAGUARD® using AiCaP CANbus or as stand alone sensor using RS-232. The sensor is easily integrated in other measurement systems with third party data loggers.

  • Pressure Sensor 4646/4646R

    Pressure Sensor 4646/4646R

    Pressure Sensor 4646/4646R is a compact fully integrated sensor for measuring the pressure level and the water temperature. The 4646 sensor is designed to be mounted on the AADI SEAGUARD® using AiCap CANbus, or in other measurement systems using the RS-232 interface. The 4646R sensor is designed for use with long cables by means of an RS-422 full duplex interface. The R-version can not be used in SEAGUARD® applications.

  • Temperature Sensors

  • Temperature Sensor 4050

    Temperature Sensor 4050

    Temperature Sensor 4050 is a compact fully integrated sensor for measuring the water temperature. The sensor is designed to be mounted on AADI RCM 9, RCM 11.The sensor can also be used as stand alone, and is easily integrated in other measurement systems with third party dataloggers.

  • Temperature Sensor 4060

    Temperature Sensor 4060

    Temperature Sensor 4060 is a compact fully integrated sensor for measuring the water temperature. The sensor is designed to be mounted on the AADI SEAGUARD® Platform. The sensor can also be used as stand alone (RS232), and is easily integrated in other measurement systems with third party dataloggers.

  • Temperatur Sensor 4880/4880R

    Temperatur Sensor 4880/4880R

    Temperature Sensor 4880/4880R is a compact fully integrated sensor for measuring the water temperature. The sensor is designed to be mounted on the AADI SEAGUARD® Platform and in other measurement systems.

  • Wave and Tide Sensor

  • Wave and tide sensor 4648/R

    Wave and tide sensor 4648/R

    Wave and tide sensor 4648/4648R is a compact fully integrated sensor for measuring the wave and tide conditions. The 4648 sensor is designed to be mounted on the AADI SEAGUARD® using AiCaP CANbus or in other measurement systems using RS-232 interface. The 4648R sensor is designed for use with long cables by means of an RS-422 full duplex inetrface. The R-version can not be used in SEAGUARD® applications.

  • Turbidity Sensors

  • Model 4112 - Turbidity Sensor

    Model 4112 - Turbidity Sensor

    Turbidity Sensor 4112 is an 0-5V analog sensor designed for SEAGUARD® applications. The sensor fits directly onto the SEAGUARD® Top end Plate using one of the four analog channels.

  • Model 4705 - Turbidity Sensor

    Model 4705 - Turbidity Sensor

    Turbidity Sensor 4705 fits directly onto the top end plate of the RDCP. Turbidity sensor 4705 consists of Turbidity sensor 4640 and Analog converter 4649.

  • Turbidity/Temperature Sensor 3712

    Turbidity/Temperature Sensor 3712

    A rugged sensor for measuring the turbidity of the water based on scattered infra-red light and temperature by means of a thermistor.

  • Water Level Sensors

  • Wave and Tide

  • Wave and Tide Sensor 4648/4648R

    Wave and Tide Sensor 4648/4648R

    Wave and Tide Sensor 4648/4648R is a compact fully integrated sensor for measuring the wave and tide conditions. The 4648 sensor is designed to be mounted on the AADI SEAGUARD  using AiCaP CANbus or in other measurement systems using RS-232 interface. The 4648R sensor is designed for use with long cables by means of an RS-422 full duplex inetrface. The R-version can not be used in SEAGUARD  applications.

  • Air Sensors

  • Mira Visibility Sensor 3544/3544 EX

    Mira Visibility Sensor 3544/3544 EX

    A compact and rugged visibility sensor designed for use with Aanderaa Weather Stations, Road Weather Stations and Environmental Monitoring Systems.

  • Net Radiation Sensor 2811

    Net Radiation Sensor 2811

    Net Radiation Sensor 2811 measures the difference between incoming and outgoing radiation at the Earth´s surface. It is designed for use with Aanderaa Automatic Weather Station 2700.

  • Rainfall Sensor 3864

    Rainfall Sensor 3864

    A Rain-o-matic® water precipitation sensor adapted for use with Aanderaa Field Monitoring Equipment.

  • Relative Humidity Sensor 3445

    Relative Humidity Sensor 3445

    Relative Humidity Sensor 3445 is designed for use with the Aanderaa Automatic Weather Station 2700, Dataloggers 3660 or 3634 and other sensor readout units.

  • Road Condition Sensor 3565

    Road Condition Sensor 3565

    A sensor monitoring road surface temperature, wet or dry road, snow coverage and the salinity (freezing point) of the moisture on the road surface.

  • Solar Radiation Sensor 2770

    Solar Radiation Sensor 2770

    A sensor for incoming solar and sky radiation, specially designed for use with Aanderaa Automatic Weather Station 2700 and Datalogger 3660.

  • Wind Speed Sensor 2740/2740 EX

    Wind Speed Sensor 2740/2740 EX

    This sensor will measure the average and maximum wind speed (gust) during the sampling interval. It is designed for use with the Aanderaa Automatic Weather Stations, Sensor Scanning Unit 3010, Dataloggers 3660/3634, Display Units 3315/3017 or Wind Display Panels 3400/3300.

  • SEAGUARD Products

  • AADI SmartGuard - Recorder Platforms

    AADI SmartGuard - Recorder Platforms

    SeaGuard Recorder platforms provides the user with the possibility to perform long term monitoring of sea and inland water using the latest technology for measurement.

  • AADI SmartGuard - Model WTR - Wave and Tide Recorder

    AADI SmartGuard - Model WTR - Wave and Tide Recorder

    The SEAGUARD WTR is a robust instrument based on the SEAGUARD Platform. It is a self contained instrument for measuring wave parameters, water level and temperature. The SEAGUARD WTR application areas are in fixed installations, either deployed in a seabed installation in shallow waters, or mounted onto a fixed structure in the upper water column. Typical applications for the sensor are measurements of wave and tide in ports and harbors, marine...

  • AADI SmartGuard - Model CTD - Conductivity, Temperature and Depth Robust System

    AADI SmartGuard - Model CTD - Conductivity, Temperature and Depth Robust System

    SeaGuard CTD Recorders may be used as a multi-parameter instrument in the sea and in freshwater and feature a modular plug-and-play architecture. SeaGuard CTD Recorders: Conductivity, Temperature and Depth. SEAGUARD® Products are based on modern technology and are the basic modules of our underwater observatory.  

  • AADI SmartGuard - Model O2 - Oxygen Recorder

    AADI SmartGuard - Model O2 - Oxygen Recorder

    Provides the user with the possibility to perform long term monitoring of sea and inland water oxygen content using the latest technology for oxygen measurement SEAGUARD® Products are based on modern technology and are the basic modules of our underwater observatory. It may be used as a multi-parameter instrument in the sea and in freshwater and feature a modular plug-and-play architecture using CANBus based AiCap smart sensor technology. It...

  • AADI SmartGuard - Real-Time Communication System

    AADI SmartGuard - Real-Time Communication System

    The Aanderaa Real-Time Communication System is designed to provide our customers and system integrators with powerful and efficient tools for data collection and control of our latest generation oceanographic instruments.

  • AADI SmartGuard - String System

    AADI SmartGuard - String System

    The AADI SEAGUARD String System is a complete and flexible subsea observatory, for measurements of e.g. dissolved oxygen, conductivity, temperature, current, pressure and tide.

Products by Teledyne RD Instruments

  • Teledyne RD Instruments - Citadel CT - EK Digital

    Teledyne RD Instruments - Citadel CT - EK Digital

    Teledyne RD Instruments CITADEL CT-EK Sensor provides high accuracy conductivity and temperature measurements in a package that can be readily adapted to various user platforms.The instrument relies on an innovative, inductively coupled conductivity sensor, which provides high-accuracy, stable readings.The sensor is self-flushing, so no pumps are required. A high-grade Platinum Resistance Thermometer (PRT) provides stable temperature readings for...

  • Teledyne RD Instruments - Citadel CT - EK Analog

    Teledyne RD Instruments - Citadel CT - EK Analog

    Teledyne RD Instruments CITADEL CT-EK Sensor provides highaccuracy conductivity and temperature measurements in a package that can be readily adapted to various user platforms. The instrument relies on an innovative, inductively coupled conductivity sensor, which provides high-accuracy, stable readings. The sensor is self-flushing, so no pumps are required. A high-grade Thermistor provides stable temperature readings for calculation of high-accuracy...

  • Teledyne RD Instruments - Citadel CTD - ES/ER

    Teledyne RD Instruments - Citadel CTD - ES/ER

    The CITADEL CTD-ES incorporates proven inductively coupled conductivity sensor technology with a platinum resistance thermometer and micromachined silicon pressure sensor to provide highly accurate and stable readings.

  • Teledyne RD Instruments - Citadel CTD - NH

    Teledyne RD Instruments - Citadel CTD - NH

    The CITADEL CTD-NH provides scientific-quality conductivity, temperature, and depth measurement capability in an extremely rugged package. This new CTD utilizes the patented Non-eXternal Inductive Cell (NXIC) conductivity sensor, and represents a new generation of extremely durable precision measurement instruments

  • Teledyne RD Instruments - Citadel CTD - NV

    Teledyne RD Instruments - Citadel CTD - NV

    The CITADEL CTD-NV provides scientific-quality conductivity, temperature, and depth measurement capability in an extremely rugged package. This new CTD utilizes the patented Non-eXternal Inductive Cell (NXIC) conductivity sensor, and represents a new generation of extremely durable precision measurement instruments.

  • Teledyne RD Instruments - Workhorse Sentinel ADCP

    Teledyne RD Instruments - Workhorse Sentinel ADCP

    The self-contained SENTINEL is Teledyne RD Instruments’ most popular and versatile Acoustic Doppler Current Profiler (ADCP) configuration, boasting thousands of units in operation in over 50 countries around the world.

  • Teledyne RD Instruments - Workhorse Mariner ADCP

    Teledyne RD Instruments - Workhorse Mariner ADCP

    Teledyne RD Instruments’ Workhorse Mariner Acoustic Doppler Current Profiler (ADCP) has become the instrument of choice for researchers and commercial surveyors working in coastal waters. The Mariner offers all of the benefits of RDI’s traditional ADCP products in a compact package designed specifically for coastal hull-mount applications. The unit is easily integrated into the vessel’s DGPS input to provide integrated ADCP readings with precise position...

  • Teledyne RD Instruments - ChannelMaster H-ADCP

    Teledyne RD Instruments - ChannelMaster H-ADCP

    The compact, flexible, and affordable CHANNELMASTER is a horizontally-oriented Acoustic Doppler Current Profiler (H-ADCP) designed to collect high-accuracy water velocity, stage, and discharge data for a wide array of applications.

  • Teledyne RD Instruments - Workhorse Monitor ADCP

    Teledyne RD Instruments - Workhorse Monitor ADCP

    The MONITOR is Teledyne RD Instruments’ most popular direct-reading Acoustic Doppler Current Profiler (ADCP). The unit is typically bottom frame-mounted and hard-wired to shore to provide real-time monitoring of coastal currents.

  • Teledyne RD Instruments - StreamPro ADCP

    Teledyne RD Instruments - StreamPro ADCP

    Teledyne RD Instruments’ STREAMPRO ADCP (Acoustic Doppler Current Profiler) represents a revolutionary advancement in streamflow measurement. You can accurately measure discharge in shallow streams in a matter of minutes—a fraction of the time required using traditional hand-held devices. With StreamPro there’s no need to move from station to station to obtain single-point velocity data or compute the discharge by hand; streamflow measurements are...

  • Teledyne RD Instruments - Workhorse Quartermaster ADCP

    Teledyne RD Instruments - Workhorse Quartermaster ADCP

    Teledyne RD Instruments’ WORKHORSE QUARTERMASTER Acoustic Doppler Current Profiler (ADCP) has been designed to fill the gap between Teledyne RDI’s higher frequency 300 kHz Workhorse units and the 75 kHz Long Ranger. The Quartermaster is ideally suited for current profile measurements that may require up to 300m range. The unit provides an unsurpassed combination of range, resolution, and versatility, thanks to Teledyne RDI’s Broadband technology.

  • Teledyne RD Instruments - Workhorse Rio Grande ADCP

    Teledyne RD Instruments - Workhorse Rio Grande ADCP

    The WORKHORSE RIO GRANDE ADCP (Acoustic Doppler Current Profiler) is an accurate, rapid-sampling current profiling system designed to operate from a moving boat. The result is the fastest, safest, and most flexible method for measuring discharge.

  • Teledyne RD Instruments - Sentinel V, Next Gen ADCP

    Teledyne RD Instruments - Sentinel V, Next Gen ADCP

    After fifteen years of astounding success, the next generation of Teledyne RDI ADCP products has arrived. By all accounts, our Workhorse Acoustic Doppler Current Profiling (ADCP) products continue to live up to their name. With nearly 13,000 Workhorse products delivered worldwide, and hundreds of thousands of hours of data collected, Workhorse remains the standard to which others aspire. Now the company that brought you this technology is ready to wow...

  • Teledyne RiverPro - RiverPro ADCP

    Teledyne RiverPro - RiverPro ADCP

    Teledyne RD Instruments is pleased to introduce RiverPro -- the newest member of our growing family of Acoustic Doppler Current Profilers (ADCPs) for inland Water Resources applications.

  • Teledyne RD Instruments - RiverRay ADCP

    Teledyne RD Instruments - RiverRay ADCP

    Go straight to work collecting highly accurate stream and river discharge data with the RIVERRAY ADCP (Acoustic Doppler Current Profiler). This economical turnkey system comes complete with: the RiverRay ADCP, a custom-designed boat, user-friendly software, and convenient wireless communication—everything you need to begin making precision river discharge measurements.

  • Teledyne RD Instruments - Vertical Acoustic Doppler Current Profiler (V-ADCP)

    Teledyne RD Instruments - Vertical Acoustic Doppler Current Profiler (V-ADCP)

    The Vertical Acoustic Doppler Current Profiler (Vertical ADCP) is designed for the high-accuracy measurement of water flow, level and velocity profile in open channels, rivers, streams, and irrigation channels. The Vertical ADCP can be deployed as a self-contained instrument recording data for later use; as a real-time instrument for real-time measurements; or as a portable flow meter, with the option to move from station to station.

  • Teledyne RD Instruments - Citadel TS - NH

    Teledyne RD Instruments - Citadel TS - NH

    The Teledyne RD Instruments CITADEL TS-NH THERMOSALINOGRAPH is a compact, low-maintenance system with exceptional stability for monitoring sea surface salinity, as well as sound velocity and water density.

  • Teledyne Sentinel - Sentinel V ADCP

    Teledyne Sentinel - Sentinel V ADCP

    After fifteen years of astounding success, the next generation of Teledyne RDI ADCP products has arrived. By all accounts, our Workhorse Acoustic Doppler Current Profiling (ADCP) products continue to live up to their name. With nearly 13,000 Workhorse products delivered worldwide, and hundreds of thousands of hours of data collected, Workhorse remains the standard to which others aspire. Now the company that brought you this technology is ready to...

Products by Falmouth Scientific, Inc. (FSI)

  • Sensors

  • PLUS Family - Model ACM-PLUS - Acoustic Current Meters

    PLUS Family - Model ACM-PLUS - Acoustic Current Meters

    High-accuracy acoustic current meters with vector-averaged current speed and direction.  ACM-PLUS - user selectable 2D or 3D point velocity measurements with internal compass and tilt correction for deep (ACM-PLUS-7000) or shallow (ACM-PLUS-200) water

  • Structural and Riser Monitors

    Structural and Riser Monitors

    Structural and Riser Monitors for applications such as: Vibration- and Drilling-Induced Vibration (VIV/DIV) analysis studies. Underwater structure motion monitoring for stress analysis. Real-time stress data during oil flow line installations. Analysis of structural response to stress-inducing events. Clamps and mounting hardware are designed to be ROV deployable and retrievable so that instruments can be moved to other risers and used on multiple...

  • Systems

  • Bubble Gun - Model HMS-620 - Portable Low Frequency Acoustic Seismic Sub Bottom Systems

    Bubble Gun - Model HMS-620 - Portable Low Frequency Acoustic Seismic Sub Bottom Systems

    Portable Low-Frequency Acoustic Seismic Sub-Bottom Systems. Low-frequency acoustic signals provide superior sub-bottom signal penetration vertically through coarse sand, gravel tills, and other difficult-to-penetrate sediments. Small component size, portability, and low power requirements make this a valuable tool for any survey platform. Multiple Sources can be synchronized to a common trigger without need for external timing control. Repeatable...

  • Model HMS-622 - Chirpceiver

    Model HMS-622 - Chirpceiver

    The HMS-622 CHIRPceiver and its associated transducers and arrays can fill a wide range of sub-bottom survey needs. It is available in dual and single frequency configurations, and supports three frequency bands: standard LF (1KHz-10KHz), as well as optional ULF (200Hz-2KHz) and HF (8KHz-23KHz). A direct A/D input is available for the FSI Bubble GunTM or other seismic systems, and it has an...

  • Model HMS-1400 - Portable Sidescan Sonar System

    Model HMS-1400 - Portable Sidescan Sonar System

    Portable digital sidescan towfish and Sonar interface with true 16-bit processing,  Toughbox workstation, and GeoDAS software for high-resolution survey imaging. Easy-to-use and low-cost, the HMS-1400 System provides single- or dual-frequency operation with depth, heading, and attitude sensors. The powerful GeoDAS software offers an extensive suite of capabilities common in more expensive systems, including display of real-time mosaicing of...

  • Model ELPF-553 - Stand-Alone Flasher

    Model ELPF-553 - Stand-Alone Flasher

    These are extremely small, lightweight, battery-powered, intelligent devices that can be mounted directly on AUVs, Gliders, or other underwater equipment for recovery after their mission duration has elapsed. Multiple user programmable settings allow for selection of delay, timing, flashing, and frequency options which enable use in a variety of different applications. The Stand-Alone Flasher uses high power, high...

  • Echo-Angler - Model MCR-554 - 16-Channel Acoustic Receiver

    Echo-Angler - Model MCR-554 - 16-Channel Acoustic Receiver

    The MCR-554 Echo-Angler is 16-channel acoustic receiver used for relocating acoustic sound sources. Using the latest in underwater acoustic technology, the MCR-554 allows the tracking and recovery up to 16 different acoustic Pingers which emit industry standard acoustic frequencies.

Products by KC-Denmark A/S

  • Autonomus Benthis Lander

  • KC - Custom Made Deep Sea Lander

    KC - Custom Made Deep Sea Lander

    Antenna: manufactured from 2 meter Ø28mm stainless steel tube, mounted on a floatation rack with 3 pcs of powerful springs, manufactured from AISI 316 stainless steel 316. 2 pcs/each.

  • KC - Frame to Deep Sea Lander

    KC - Frame to Deep Sea Lander

    The frame can be designed specifically for your purpose or based on our tripodal standard vehicle. Manufacturing in aluminium, steel, AISI 316 stainless steel and titanium is routine at our workshop. Floatation can be either glass spheres or foam. We offer exact weight calculations and recommend minimum buoyancy for your vehicle.

  • KC - Xenon and Deep Sea Beacon Equipment

    KC - Xenon and Deep Sea Beacon Equipment

    Antenna for radio or satellite beacons. The flash and radar reflector are manufactured from reinforced fibre glass with a bend restrictor at the base The autonomous vehicles can be equipped with units for: water column profiling, chamber incubation, micro profiling over the sediment-water interface, sediment core catching, water sampling or injecting in chambers or in sediment cores.

  • KC - Custom Made Lander

    KC - Custom Made Lander

    Antenna; manufactured from 2 meter Ø28mm stainless steel tube, mounted on a floatation rack with 3 pcs of powerful springs, manufactured from AISI 316 stainless steel 316. 2 pcs/each.

  • Pressure Stable Battery Cylinder

  • KC - Pressure Stable Battery Cylinder for 6000 Meters

    KC - Pressure Stable Battery Cylinder for 6000 Meters

    Application: Battery box 100.217 rated for 6000 m depth. With room for programmable timer (USB or RS-485 interface) and pressure transmitter (optional) which can be used for Niskin rosette racks, sediment trap stations, plankton pumps, small multi water sampler station and lander systems.

  • Current Meter Measurement

  • KC - Field Procedures for FST Hemispheres

    KC - Field Procedures for FST Hemispheres

    The hemisphere method describes near-bottom flow conditions in watercourse. The method is based on a simple concept: Which weight of a hemisphere exposed to a flow is moved by a given current from a reform plate. The set of hemispheres consists of 21 identical hemispheres with different specific gravity.

  • KC - Current Meter Rack

    KC - Current Meter Rack

    The rack is for use with SEBA and OTT current meters (9 mm o.d. pins) during flow measurements in streams and rivers. The rack consist of a movable part with a stirrup for holding the current meter and a fixed part with a foot and a centimeter graduated scale (5 cm indications). By operating the spring loaded handle, the current meter can be positioned at any height above the sediment and the position read at the scale. The CURRENT METER RACK can be...

  • KC - Digital Flow Meter with Back-Run Stop

    KC - Digital Flow Meter with Back-Run Stop

    For determining the amount of water passing through a plankton net. For vertical pull only. For a horizontal pull you can also use flow meter 23.090. Diameter of propeller/counter body: 70/32 mm, length 185 mm, 5-digit counter; easy installation by a triple point connection of the nosepiece. With back-run stop for vertical operation.

  • KC - Digital Flow Meter

    KC - Digital Flow Meter

    Short description: For determining the amount of water passing through a plankton net. For horizontal pull only. Diameter of propeller/counter body: 70/32 mm, length 185 mm, 5-digit counter; easy installation by a two-point connection of the nose piece. Can be used for full oceanographic depth. (6000 m).

  • Dredges

  • KC - Triangular Dredge

    KC - Triangular Dredge

    The KC BIOLOGICAL DREDGE is made of heavy duty AISI 316 stainless steel. The triangular frame is furnished with a row of teeth guiding plants and algae into the bottom of the net. A coarse meshed 2 cm Nylon net of 100 cm length for collecting biological and/or mineralogical samples is mounted on the frame. A fine meshed net can on request be mounted inside the coarse net for collection of zooplankton. The dredge is held in position by steering arms...

  • KC - Agassiz Trawl

    KC - Agassiz Trawl

    Application: The Agassiz trawl is used to collect organisms, particularly invertebrates, living on the ocean bottom.

  • KC - Epibenthic Sledge

    KC - Epibenthic Sledge

    Application: The Epibenthic sledge is a system for sampling benthic and benthopelagic faunas. The sledge contsists of a a rectangular aluminium frame (sea water resistant) with a mesh net attached to it. When towed along the seabed, its weight scrapes into the benthos, collecting any organisms on the surface or in the first centimetres of the sediment.

  • KC - Ockelman Sledge, Modified

    KC - Ockelman Sledge, Modified

    Made from aluminium. Opening: 30 x 15 cm, located 3 cm above the sea bed. Net bag: Mesh size 1000 µ. Net bag, length: 100 cm. Protection for net bag: Rubber plate. Dimensions: L x W x H: 160 x 570 x 22 cm. Weight: 14 kg.

  • KC - Triangle Dredge

    KC - Triangle Dredge

    Triangle dredge for heavy performance. The dredge can be used without the rubber plate. When using the rubber plate it is necessary to use some kind of buoyancy to ensure the correct position of the dredge.

  • Mini Micro Profilers

  • KC - Mini Micro Profilers with Microsensors

    KC - Mini Micro Profilers with Microsensors

    A novel portable instrument has been designed for in-situ microsensor measurements. The micro profiler, which can be equipped with microsensors for measurements of oxygen, pH, sulphide (S -- or H2S) and temperature, is ideal for a wide range of applications including: Oxygen respiration. Benthic primary production. Quantification of sulphide oxidation and sulphate reduction by measurement with a sulphide (gas or ion) microsensor for use in bio-films...

  • Plankton Nets

  • KC - Model Ø25 cm - Small Plankton Net

    KC - Model Ø25 cm - Small Plankton Net

    The upper cylindrical net is made of strong Beaver Nylon with a diameter of Ø25 cm and a length of 15 cm. The conical net bag is made of Monodur Nytal (Nylon) and it is 40 cm deep. The bag is available in all mesh sizes.

  • KC - Model Ø30 cm - Plankton Net

    KC - Model Ø30 cm - Plankton Net

    The upper part of the net is made of strong Beaver Nylon. Standard mounting with 3 pcs. of polyester line Ø3 mm. with bridle, length 60 cm.

  • KC - Model Ø40 cm - Plankton Net

    KC - Model Ø40 cm - Plankton Net

    The upper part of the net is made of strong Beaver Nylon. Standard mounting with 3 pcs. of polyester line Ø5 mm. with bridle, length 60 cm.

  • KC - Model Ø50 cm - Plankton Net

    KC - Model Ø50 cm - Plankton Net

    Outer diameter. 50 cm. Length of net: 200 cm. Length, overall: 280 cm. Mesh size: 50 - 500 µ, order no. 23.020 or 20-40 µ 23.020A, please specify upon order. Inclusive net bucket 23.021.

  • KC - Model WP-2 - Plankton Net

    KC - Model WP-2 - Plankton Net

    The WP-2 plankton net can be equipped with a digital flow meter (Optional) for determing the amount of water passing through the plankton net.Digital flow meter, model 23.090.Digital flow meter with back-run stop, model 23.091.

  • Plankton Pumps

  • KC - Plankton Pumps for 150 m Depth

    KC - Plankton Pumps for 150 m Depth

    The pump itself is a GRUNDFOS pump made from AISI 304 stainless steel. 3 models are available: 23.570: Capacity of 18.000 liter/hour at 0 meter water column). Power supply: 230 VAC. Max. depth 60 m.

  • KC - Plankton Pumps for 300 m Depth

    KC - Plankton Pumps for 300 m Depth

    The pump itself is a GRUNDFOS pump made from AISI 304 stainless steel. 3 models are available: 23.570: Capacity of 18.000 liter/hour at 0 meter water column). Power supply: 230 VAC. Max. depth 60 ml.

  • Sediment Samplers

  • KC - Model HAPS - Bottom Corer

    KC - Model HAPS - Bottom Corer

    Application: The KC HAPS Bottom corer is highly suitable for taking well defined, undisturbed samples from hard as well as soft sediments. This can be seen by a clear water phase above the sediment surface.

  • KC  - Kajak Sediment Corer

    KC - Kajak Sediment Corer

    Adapter for Ø80 mm tubes. (Optional). Will fit on all models with quick change, (13.030). A model with 2 tubes are available.

  • Sediment Trap Station

  • KC - Model Ø80 mm - Sediment Trap Station Tubes

    KC - Model Ø80 mm - Sediment Trap Station Tubes

    General: The construction of the sediment trap array ensures a permantly vertical position of the sampling tubes during deployment. The steering fin (optional) and the pivot joints force the array to be held at right angle to the current.

  • KC - Sediment Trap Station Ø110 mm Tubes

    KC - Sediment Trap Station Ø110 mm Tubes

    General: The construction of the sediment trap array ensures a permantly vertical position of the sampling tubes during deployment. The steering fin (optional) and the pivot joints force the array to be held at right angle to the current.