Only show results in Virginia? Ok

digester cover Equipment

  • Premium

    WesTech - Digester Covers

    WesTech provides innovative designs for custom digester covers using the latest structural standards while integrating ease of erection and economical value. WesTech offers three major structural designs: Steel Truss, Radial Beam, and DuoSphere™. Our Steel Truss and Radial Beam structures can be configured to fixed or buoyant configurations. ...

    By WesTech Engineering, Inc. based in Salt Lake City, UTAH (USA). from Anaerobic Digestion Product line

  • Premium

    EWT - Steel Digester Covers

    Ovivo provides a variety of EWT steel digester covers digester covers. Each digester cover is constructed as a dome-shaped segment of a sphere, offering maximum strength and structural integrity. Ovivo offers the Type F cover (fixed), frequently used as the primary of first stage digester in a two stage system and the Type GV (gasholder) which ...

    By Ovivo (Formerly Eimco Water Technologies) based in Salt Lake City, UTAH (USA). from Biological Process Systems Product line

  • SPS - Digester Covers

    Digester covers are used over the anaerobic digester concrete tank to seal the digested material and contain the gaseous by products. Anaerobic digesters convert the raw odorous sludges to a biologically stable material by further breaking down the volatile organic solids. The bacterial process converts the raw material to organic acids along with ...

    By SPS Engineering, Inc. based in North Salt Lake, UTAH (USA). from Other Product line

  • OTI - Fixed Digester Covers

    Least expensive of all OTI’s digester covers to design, produce and to install. Normally is used where sludge level in the digester does not vary significantly. The cover is supported at the top of the digester tank wall on bearing plates and restrained from upward forces with anchoring saddles. Custom designed for specific project loads ...

    By Olympus Technologies, Inc. (OTI) based in Eugene, OREGON (USA). from Digester Covers Product line

  • Anaerobic Digester Covers

    The JDV/Ralph B. Carter Anaerobic Digester Covers, for over 50 years, have provided Municipalities and Industry a safe, proven design for efficient installation, long operation and service life of the Anaerobic Digestion Process. JDV has extensive experience in refitting your existing installation or can provide design and installation support and ...

    By JDV Equipment Corporation based in Dover, NEW JERSEY (USA). from Anaerobic Digestion Product line

  • Digester Covers: Fixed

    Fixed covers are used in digesters with no variation in total volume, and are often used on the primary digester in a two-stage system. The sludge volume can be varied, but only by varying the gas volume at the same time so as to keep the total volume constant. If gas is to be pressurized for use, it must also have a companion floating cover ...

    By Walker Process Equipment based in Aurora, ILLINOIS (USA).

  • Premium

    WesTech DuoSphere - Double Membrane Gas Holder

    Over the years, WesTech has supplied our customers with anaerobic digestion equipment that has added value to their plant operations. WesTech continues to provide valuable solutions with the DuoSphere™ Dual Membrane Gasholder. The DuoSphere™ offers innovative designs for digester gas storage and alternatives for conventional digester ...

    By WesTech Engineering, Inc. based in Salt Lake City, UTAH (USA). from Anaerobic Digestion Product line

  • Premium

    Shand & Jurs - Model 97100E - Electric Drip Trap

    The Shand & Jurs Biogas 97100E Electric Drip Trap provides for the continuous, safe removal of condensate from low points in low pressure gas piping systems. Available in either 3 or 6 quart sizes and with 1' NPT inlets and outlets, the Shand & Jurs Biogas 97100E adapts to any condensation or drainage collection requirement. The 97100E can be ...

  • Premium

    Shand & Jurs - Model 97101E - High Pressure Drip Trap with Electric Actuator

    The Shand & Jurs Biogas 97101E High Pressure Drip Trap with Electric Actuator provides for the automatic, continuous, safe removal of condensate from low points in high pressure gas piping systems. The S&J 97101E is available in 4 quart or 6 quart sizes and with 1' NPT inlets and outlets. It easily adapts to any condensation or drainage collection ...

  • Premium

    Shand & Jurs - Model 92500 - Cover Position Indicator

    The Shand & Jurs Model 92500 Retrofit Gauge is specifically designed to replace existing Varec Model 2500 Gauges and GSI 2500 Model in existing installations. The Shand & Jurs 92500 allows for improvement in accuracy while minimizing field labor to replace existing gauges.

  • Premium

    Shand & Jurs - Model 94306 - Vertical Flame Arrester

    The Shand & Jurs Flame Arresters are designed to provide a positive flame stop on low pressure tanks, storage tanks and anaerobic digesters containing flammable liquids, solvents or gases having a low flash point. The 94306 not only provides exceptional protection against fire from external ignition, but also offers maximum flow capacity.

  • Premium

    ennox - Model PSD - Spraying Unit

    Floating covers or sludge accumulations forming on the substrate surface in the digester can be combated with a pivoting stainless steel spraying unit PSD. Normally the spraying unit is welded into the gas dome or manhole cover, can be rotated 360° and can pivot within the space available. The water connection can be achieved with a STORZ or ...

    By ennox biogas technology GmbH based in Hard, AUSTRIA. from Digester Equipment Product line

  • OTI - Floating & Gasholder Covers

    Normally used where sludge level is variable and/or digester gas is required to be stored under the digester cover. Because the cover sits on a pressurized volume of digester gas, it never comes in contact with the sludge. Unique ballast designs are used to fine tune the design to specific operating conditions. OTI’s robust slide-guide ...

    By Olympus Technologies, Inc. (OTI) based in Eugene, OREGON (USA). from Digester Covers Product line

  • OTI - Floating Buoyant Covers

    Normally used when sludge level is variable and no digester gas is required to be stored under the digester cover. Although the buoyant covers are more costly to fabricate, the design work is more intensive, and they are generally more costly to install, it is the most stable cover related to potential imbalance or “tipping”. Unique ...

    By Olympus Technologies, Inc. (OTI) based in Eugene, OREGON (USA). from Digester Covers Product line

  • Air Supported Membrane Roof

    Air supported membrane roofs, or as you wish double membrane covers, offer a lot of advantages and certainty in the case of digestion installations.

    By Monostore Ltd based in Kampen, NETHERLANDS. from Covers Product line

  • AKTEK - Model TP1200M - Pressure/Vacuum Relief Valve w/Pipe-Away

    AKTEK Model TP1200M is used for pressure and vacuum relief where vapours must be piped away. Special pallets in the Model TP1200M housing virtually eliminate the intake of air and the escape of vapours except during normal tank breathing, thus reducing the loss of product and protecting the tank from possible damage. Escaping vapors are piped away ...

    By Aktek Technology Engineering Co. Ltd. based in Kullar, TURKEY. from DIGESTER COVER EQUIPMENTS Product line

  • Groth - Model 1200A - Pressure/Vacuum Relief Valve

    Model 1200A is designed to vent to atmosphere to protect your tank from damage created by over-pressure or excessive vacuum. Costly product evaporation losses due to normal tank 'breathing' are greatly reduced. Because the Model 1200A retains toxic vapors, atmospheric contamination is minimized. This helps to provide increased fire protection and ...

    By Groth Corporation based in Stafford, TEXAS (USA). from Digester Cover Equipment Product line

  • LemTec - Gas Collection Covers

    LemTec gas collection covers provide the ultimate solution for applications requiring complete gas containment and gas collection, whether solely for odor control, or for digester gas reuse applications, in ponds or steel/concrete tanks. LemTec gas collection cover systems are designed to meet each customer’s requirements.

    By Lemna Technologies, Inc. based in Minneapolis, MINNESOTA (USA). from Covers Product line

  • AKTEK - Model TP1100M - Pressure/Vacuum Relief Valve

    AKTEK Model TP1100M is designed to vent to atmosphere to protect your tank from damage created by over-pressure or excessive vacuum. Costly product evaporation losses due to normal tank 'breathing' are greatly reduced. Because the Model TP1100M retains toxic vapours, atmospheric contamination is minimized. This helps to provide increased fire ...

    By Aktek Technology Engineering Co. Ltd. based in Kullar, TURKEY. from DIGESTER COVER EQUIPMENTS Product line

  • AKTEK - Model TP2100M - Pressure Relief Valve w/Pipe-Away

    AKTEK Model TP2100M relief valves are designed with inlet and outlet flanges of the same size to reduce installation costs by having smaller downstream piping. Model TP12200M valves are designed for systems requiring only pressure relief. Escaping vapours are piped away through a flanged outlet connection. This helps to provide increased fire ...

    By Aktek Technology Engineering Co. Ltd. based in Kullar, TURKEY. from DIGESTER COVER EQUIPMENTS Product line

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you