Burner Systems Applications

20 Results found
Only show results available in Virginia?
OK
  • Category: Energy & Renewables ×

  • Subcategory: Burner Systems ×

Pumping solutions for marine

by Hydro Prokav Pumps (India) Pvt. Ltd.     based in Sidco, INDIA

Fluids Handled - Fuel-injection, Oil burners, Boosting, Hydraulics, Fuel, Lubrication, Circulating and Feed Pumping.

Biogas for Cooking

by Kirloskar Integrated Technologies Limited     based in Kothrud, INDIA

This solution comprises a Biogas Digester of desired capacity working with specific substrate as input. It may or may not have H2S scrubbing system, depending on the quantity of H2S in the biogas and the requirement by the customer for cleaning it. As the heating value of biogas is almost half that of cooking LPG, specially designed biogas burners are provided to improve cooking speed. Depending on the demand by the customer, a blower to increase gas pressure may be employed.

Emissions testing for industrial boilers and burners

by Testo Inc.     based in Sparta, NEW JERSEY (USA)

Industrial boilers and burners have their own unique characteristics. When an unexpectedly high CO is detected, the Testo 350 will automatically adjust to the situation, keeping the sensor protected at all times. Don`t worry about climbing and removing the probe from the stack, just hit the fresh air button. The measurements of O2, CO, NO and SO2, combined with automatic calculations (CO2, efficiency, excess air), provide fast tuning solutions. The 350`s compact design is better for working on a platform or small space. The automatic zero pressure measurement is ideal to monitor flow or draft induction. With a pitot tube you can quickly measure velocity and determine mass flow even during long term testing. The Testo 350 makes reporting in lbs/hour easy!

Flaring Solutions for Gas Processing Facilities

by ABUTEC LLC     based in Kennesaw, GEORGIA (US) (USA)

ABUTEC’s proprietary technology was designed to provide cost-competitive solutions and the industry’s lowest operating costs and cost of ownership. Our uniquely engineered burner system offers a significant reduction in make-up fuel over premixed surface combustion systems, thermal oxidizers or traditional pipe flares. In addition, we meet EPA requirements for 40 CFR 60.18 and local BACT (Best Available Control Technology) and MACT (Maximum Achievable Control Technology) at the state and local levels. We will perform a complete return-on-investment analysis for you while showing you your total cost of ownership.

Flaring Solutions for the Upstream Oil & Gas Industry - Oil & Gas Production (Enclosed Combustors)

by ABUTEC LLC     based in Kennesaw, GEORGIA (US) (USA)

The EPA mandates that all upstream oil and gas operators install factory-certified combustors that meet new Quad O compliance standards, or perform field testing on the flare system post-installation. ABUTEC offers the only compliance-ready combustors available to the market, making expensive testing no longer necessary for our customers. The use of enclosed combustors is an integral piece of the extraction process and affords companies the opportunity to operate in extreme conditions while still maintaining low emissions and following Quad O regulations.

Flaring Solutions for the Petrochemical & Refinery Industry

by ABUTEC LLC     based in Kennesaw, GEORGIA (US) (USA)

ABUTEC’s goal in the petrochemical and refinery industry is to save you money. ABUTEC’s vapor combustor and enclosed flare line offers flexible and resilient burner technology to handle heavy hydrocarbon gases down to low quality or inert gases. We will save you money on capital costs and we will offer you a very fast payback (as low as 2 months) based on reducing the amount of make-up fuel and pilot gas required. This revolutionary technology is designed for you!

Several waste gas streams: Short, high concentration peaks and a constant |medium concentration

by Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control     based in Graz, AUSTRIA

Concentration peaks and liquid waste posed a tough challenge on the air pollution control system. With the CTP solution, this waste is not only disposed of but also reduces the burner energy considerably.

Flow Measurement instrumentation for superior natural gas measurement & control

by Sierra Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

Precise measurement of natural gas requires high accuracy, low pressure drop and direct mass flow reading—all the hallmarks of Sierra’s immersible thermal, mass vortex and thermal mass flow controllers. Our mass flow controllers are ideal for natural gas flow measurement with 100:1 turndown and no moving parts, providing a robust MFC solution. Our natural gas flow measurement instruments can also handle liquefied natural gas (LNG) via our cryogenic mass vortex meters.

Alternative Fuel Production

by Superior Boiler Works, Inc.     based in Hutchinson, KANSAS (USA)

Superior Boiler Works, Inc. led the way in Ethanol production in the USA with more installed firetube boilers in Ethanol plants than any other manufacturer. Ethanol requires the distillation of sugars into an alcohol fuel. Superior’s products are used to generate heat needed for the ethanol distillation processes, heating storage tanks as well as batch reactors. Additionally, Superior Boilers can be fitted with packaged burners which fire a variety of fuels from tallow to syngas to Hydrogen and most anything in between.

Gas measurement for the pulp & paper industry

by Kurz Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

The Kurz Insertion Mass Flow Meter products provide extremely reliable and accurate measurements for the harsh environment of a recovery boiler facility, without restricting airflow even in short run ducts.

Very large waste gas volumes with low contaminant concentration

by Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control     based in Graz, AUSTRIA

The CTP desorption allows for an especially high concentration factor which, in turn, reduces the cost of ownership and permits an auto-thermal operation (additional burner switched off) even when the contaminant concentration is low.

Dioxins and furans

by Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control     based in Graz, AUSTRIA

CTP's expertise in catalytic, adsorptive and regenerative thermal oxidation technology in nano gram purification makes it the best partner for these hazardous industrial processes.

Air pollution control for the natural gas processing industry

by Anguil Environmental Systems, Inc.     based in Milwaukee, WISCONSIN (USA)

The natural gas industry has seen a significant increase in activity with the discovery of new shales located throughout the world. The development of advance drilling technologies allow for extraction of gases deeper in the earth, revolutionizing the industry while creating a new demand for air and water pollution control technologies.

Secundary air flow measurement for power generation industry

by Kurz Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

Secondary Air Flow Overview: The need for accurate, repeatable & reliable combustion air measurements in power generation plants is critical to efficient operation and safety throughout the entire facility and processes. Accurate secondary air flow measurement to the burners is critical for maintaining the proper air to fuel ratio, result­ing in more complete and stable combustion, better performance and lower emissions. Coal-fired power plant applications pose a number of challenges to obtaining these critical flow measurements including large ducts, limited metering runs, poor velocity and temperature profiles, vibration and high temperatures.

Gas detection analyzers for pulp & paper mills

by Control Instruments Corporation     based in Fairfield, NEW JERSEY (USA)

Flammable non-condensible gases (NCG’s) are byproducts of the wood pulping process. Health and pollution regulations prohibit the release of these gases into the atmosphere. They are usually eliminated by passing them through an incinerator or by using them as fuel in the burner of a boiler or kiln. The incinerator, boiler or kiln however can be damaged by NCG’s which have built up explosive levels. Pulp mills require the use of our PrevEx Flammability Analyzers to monitor the NCG stream and detect and divert these dangerous concentrations before they can cause damage and shut down the mill. The PrevEx analyzers accurately measure the total concentration of flammable gases present in the NCG sample. Their high sampling speed dramatically improves response time—an important factor in pulp mill applications.

Flaring Solutions for Ethanol Loadout

by ABUTEC LLC     based in Kennesaw, GEORGIA (US) (USA)

ABUTEC’s proprietary technology was designed to provide cost competitive solutions and the industry’s lowest operating costs and cost of ownership. Our uniquely engineered burner system offers a 33% reduction in make-up fuel over premixed surface combustion systems or traditional nozzle burners. In addition, we meet state and federal requirements for 40 CFR 60.18 and local BACT (Best Available Control Technology) and MACT (Maximum Achievable Control Technology). Whether you are looking for vapor combustors, enclosed flares, ethanol loadout flares, truck loadout flares, loading terminal flares, emergency flares, or marketing terminal flares, contact us for reliable, safe solutions.

Actuators for the power generation

by Rotork     based in Bath, UNITED KINGDOM

As well as traditional power stations, applications for Rotork products are found on renewable energy generation such as solar thermal plants and on CO2 emissions reduction processes such as flue gas desulphurisation and carbon capture and storage.

Odor Control for Asphalt

by OMI Industries (OMI)     based in Long Grove, ILLINOIS (USA)

Control Asphalt Odors Naturally

The production of hot mix paving asphalt generates odors that can be strong, persistent, and a nuisance to employees and neighbors alike. Controlling and abating these odors can be a challenge.

Gas detection for the steel industry

by Crowcon Detection Instruments Ltd - a Halma company     based in Milton Park, UNITED KINGDOM

Regarded by many as providing the backbone to modern society, the steel industry is one which continues to evolve. Whether it is geographic shifts in demand or production, or challenges brought by energy or raw material costs, companies continue to develop their processes and facilities to meet them. Alongside these changes companies have also realised the requirement to minimise downtime due to unplanned maintenance and protect workers from exposure to toxic or flammable gas hazards.

Several waste gas streams: Highly contaminated oxygen-free waste gas,|and medium waste gas stream

by Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control     based in Graz, AUSTRIA

Explosive oxygen-free waste gases are disposed of and contribute to the oxidation process of the contaminants.

Need help finding the right suppliers?

Let the XPRTs do the work for you