Lubricating Oil Articles

  • Guide for Measuring Fuel Dilution in Lubricating Oil

    Fuel dilution in oil can cause serious engine damage. High levels of fuel (>2%) in a lubricant can result in decreased viscosity, oil degradation, loss of dispersancy, and loss of oxidation stability. Fuel dilution is one of the most important lubricant failure modes in internal combustion engines. It usually occurs due to ...


    By Spectro Scientific

  • P-80® Temporary Assembly Lubricants are Ideal for Appliance Assembly and Service

    Dishwashers, washers and dryers, refrigerators, mixers, blenders, and many other appliances have rubber or soft plastic components such as hoses, O-rings, seals, grommets, plugs and more. The slip resistance of these parts makes assembly difficult. P-80® temporary rubber assembly lubricants significantly reduce friction helping these parts slide easily into place. P-80® lubricants are ...

  • P-80® Lubricants are effective for Pump Seal Maintenance

    One universal goal of treatment plant operators is to keep operations running smoothly and effectively at all times. While many factors contribute to achieving this goal, one simple way to help reach this objective is to perform regular equipment maintenance. Most plants use a variety of different types of pumps. Maintaining and replacing pump seals on a regular basis helps to ensure that systems ...

  • The Social Responsibility

    Nowadays, companies are seen as environmental agents of change where they operate. These companies are influenced and influence their stakeholders through the impact they have on the environment. For the Oil&Gas market where ISA – Intelligent Sensing Anywhere operates with its remote monitoring and IoT solutions, this market has as main concern safety and reliability. The companies ...

  • Vibration surveillance: Oil rig – Power generator - Case Study

    Equipment, plant overview, Context Oil rigs are located in Gulf countries, Emirates.Rigs are operating 24/7 and powered by quite big power generator 436 kW. According to operator, generator was running at higher temperature than expected. Due to the periodic displacement of the generator in the oil field, no wired monitoring system was possible. The Wi-care sensors (6) ...


    By Wi-Care

  • Four Methods to Measure TAN/TBN in Lubrication Oil

    TOTAL ACID NUMBER A high concentration of acidic compounds in a lubricant can lead to corrosion of machine parts and clogged oil filters due to the formation ...


    By Spectro Scientific

  • Case study - Summit leveraged UL The Wercs to reach its goal of obtaining ISO 21469 certification

    Summit Industrial Products, a wholly owned subsidiary of Klüber Lubrication, is a leading manufacturer of specialty lubricants and lubricant technology. Summit manufactures more than 5,000 products in its three North American facilities, creating and maintaining over 25,000 labels to fulfill health and safety requirements. Maintaining proper labeling for its products is paramount for Summit. ...


    By UL The WERCS

  • P-80 Grip-it Quick-Drying Rubber Assembly Aid Helps Keep Parts in Place

    P-80® Grip-it Quick-Drying Temporary Rubber Assembly Lubricant is a unique product designed specifically for the assembly of rubber and soft plastic parts.  P-80® Grip-it provides lubricity to ease rubber assembly operations, then dries quickly to allow the natural tight fit of rubber to return.  P-80® Grip-it leaves a slightly tacky residue that ...

  • New and Improved Packaging and Label Design for P-80 Emulsion

    International Products Corporation (IPC) is pleased to announce the debut of a new metric container and updated package design for the pint size of P-80® Emulsion temporary rubber assembly lubricant.  A new 475 mL bottle will replace the 1 pint container; it will be available in cases of 6 and 12. For those wishing to utilize a sprayer with the new bottle, a case of 6 ...

  • MATRIX provides paperless LIMS at Castrol case study

    Background Castrol, part of BP, is a global leader in the development and manufacture of oils and lubricants used in automobiles, motor cycles, trucks, lorries, buses and agricultural machinery, the marine industry, industrial equipment and more. The Lubricant Technology Centre at Pangbourne, Berks, UK features laboratories capable of investigating all aspects of the technical life cycle, ...


    By Autoscribe Informatics

  • Microbe Edition: FOG How In-Pipe Technology Works

    Fats are esters of fatty acids and glycerol which are normally solid at room temperature. Oils are esters of fatty acids and glycerol which are normally liquid at room temperature. Grease is a general term used to describe a soft or melted animal fat or a lubricant (Campbell, 1999). Collectively they are referred to as fats, oils, and grease (FOG). The degradation of FOG that collects within the ...

  • 20th Annual Presidential Green Chemistry Challenge Awards highlight biomass- and waste-to-resource technologies

    On July 13, 2015, the U.S. Environmental Protection Agency (EPA) announced the winners of the 20th Annual Presidential Green Chemistry Challenge Awards (PGCCA) and honored them at a ceremony at the National Academy of Sciences in Washington, D.C. The PGCCAs were created in partnership with the American Chemical ...


    By Bergeson & Campbell, P.C.

  • PGCCA winners of yore: where are they now?

    With the 20th Annual Presidential Green Chemistry Challenge Awards (PGCCA) ceremony drawing near, the Biobased and Renewable Products Advocacy Group's (BRAG®) Biobased News and Policy Report decided to go back and revisit some early winners to see what has become of the ...


    By Bergeson & Campbell, P.C.

  • Recycling of Cars Made Green and Cleaner with Verderflex Peristaltic Pumps

    At the end of its’ life, a car yields on average, 140 kilos of shredder waste: 26 kg of metals, 69 kg of plastics, 11 kg of minerals and 24 kg of fibres. In Tiel, Netherlands, a Post Shredder Treatment plant (PST) was built in 2011, for the recycling of cars. The PST plant is one of the two plants in Europe that are able to recycle to approximately 95% of the waste materials. ...

  • Compressed and free of cooling lubricant - Case Study

    RUF’s briquetting press increases the efficiency of Zollner’s aluminium production Zollner AG compresses more than 100 tons of aluminium chips per year using a RUF briquetting press. The mechatronics service provider thereby reduces the volume of this recyclable material to a fraction and isolates clinging oils and emulsions. By recovering cooling lubricant and thanks to ...

  • What is the reason of ball mill adopts dynamic and static pressure bearing

    As the ball mill working conditions is rather special, it is generally start under full load, especially for stop after a long time, lubricating oil film between the neck of hollow shaft and bearing, due to the extrusion and thinning gradually until disappears, this time between the neck of hollow shaft and the bearing is boundary friction state. If the ...

  • Advantage of Shengyang Hermos CNC Internal Grinding Machine

    Advantage of Shengyang Hermos CNC Internal Grinding Machine is as below: 1. This CNC Internal Grinding machine uses a transparent protective bulletproof glass, to meet a wider range of vision safety premise (three sides transparent), easy to observe the internal situation. ...


  • Marine Diesel Oil (MDO) from used oil using Vertical Tube Evaporator (VTE) case study

    Sequoia supplied a vacuum distillation plant with its proprietary evaporators to a customer in the US Northwest for processing 50,000 gallon/day (7.5 m3/hour)of used lubricating oil and waste industrial lubricants, making MDO / vacuum gasoil (VGO). With highly reliable and robust rotating equipment and no moving parts in the evaporators, this plant is simple to operate and maintain. Cranes ...


    By Sequoia Global, Inc.

  • New Report - Global Lubricants Market Analysis, Size, Share, Trends And Forecast to 2020: Grand View Research, Inc

    The global market for lubricants is expected to reach USD 70.32 billion by 2020, according to a new study by Grand View Research, Inc. lubricants are widely used in the automotive industry for their benefits and relative lower cost. Hence, the growth of automotive market and industrial production, mainly in the emerging economies of Asia Pacific and Latin America is expected to boost the ...


  • Methods of fine oil purification

    High degree of oil purity is a normal requirement of modern hydraulic and lubrication systems. However, oil manufacturers sometimes fail to ensure the required oil purity, hence the need to purify the oil before operation One of the instruments of increasing efficiency of energy generation and consumption is reduction of resources consumed for its production with simultaneous increase ...


    By GlobeCore GmbH

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you