Waste Gas Applications

40 Results found
Only show results available in Virginia?
OK
  • Category: Energy & Renewables ×

  • Subcategory: Waste Gas ×

Biogas for Cooking

by Kirloskar Integrated Technologies Limited     based in Kothrud, INDIA

This solution comprises a Biogas Digester of desired capacity working with specific substrate as input. It may or may not have H2S scrubbing system, depending on the quantity of H2S in the biogas and the requirement by the customer for cleaning it. As the heating value of biogas is almost half that of cooking LPG, specially designed biogas burners are provided to improve cooking speed. Depending on the demand by the customer, a blower to increase gas pressure may be employed.

Wilsa ElectroWaveTM - Oil Harvesting / Removal

by Hudson Industries     based in Vienna, OHIO (USA)

WILSA Harvests Oil from Tank Bottom Sludge at Disposal Well. ElectroWave™ Technology optimizes onsite processing and reduces costs associated with saltwater disposal operations by breaking waste emulsions and recovering additional oil.

Flares for Safe Disposal of Waste & Toxic Gases

by Synchronous International Engineering Solutions Co. Ltd.     based in Bangkok, THAILAND

Our Flares are versatile in design & suitable for total destruction of waste gas/vapours. The waste gases/Vapours from petrochemical, WWTP, chemical plants have very high potential for environmental hazards. If allowed to released unburned into atmosphere. SIES offers flares and combustion systems for safe disposal of gases with high efficiency and reliability. System Designed to meet the API 521/537 norms High efficiency Burners with up to 99% thermal destruction Flares operable on fully automated, SCADA based solutions Customized & Cost effective project specific solutions Successful Installations of various types of flares at various locations.

Flaring Solutions for the Upstream Oil & Gas Industry - Oil & Gas Production (Enclosed Combustors)

by ABUTEC LLC     based in Kennesaw, GEORGIA (US) (USA)

The EPA mandates that all upstream oil and gas operators install factory-certified combustors that meet new Quad O compliance standards, or perform field testing on the flare system post-installation. ABUTEC offers the only compliance-ready combustors available to the market, making expensive testing no longer necessary for our customers. The use of enclosed combustors is an integral piece of the extraction process and affords companies the opportunity to operate in extreme conditions while still maintaining low emissions and following Quad O regulations.

Humid, corrosive and malodorous waste gases

by Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control     based in Graz, AUSTRIA

CTP's expertise with different coating systems, and an energy-saving pre-heater, protect the installation from corrosion even when waste gases are humid.

Several waste gas streams: Short, high concentration peaks and a constant |medium concentration

by Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control     based in Graz, AUSTRIA

Concentration peaks and liquid waste posed a tough challenge on the air pollution control system. With the CTP solution, this waste is not only disposed of but also reduces the burner energy considerably.

Air pollution control for the waste gasification industry

by Catalytic Products International (CPI)     based in Lake Zurich, ILLINOIS (USA)

Processes that create a synthetic gas (syn gas) in a gasification process for waste reduction, electricity generation, or steam production (CHP – combined heat and power processes) – commonly benefit from custom heat recovery systems.

Oxygen Generating Systems for Waste Gas Treatment in the Semiconductor, PV and LED Industries

by Oxygen Generating Systems Intl. (OGSI)     based in North Tonawanda, NEW YORK (USA)

Waste gas treatment is an often overlooked but important function of Semiconductor, PV and LED fabrication. Several serious accidents have taken place in factories where no abatement was installed. Even today waste treatment is often seen as a cost rather than a safety issue. There are three main reasons why waste gas treatment is installed in factories: health and safety, environmental factors, and quality control.

NORM Waste

by econ industries GmbH     based in Starnberg, GERMANY

Natural Occurring Radioactive Material consists of materials enriched with radioactive elements found in the environment. They are usually brought to the surface by oil and gas exploration or mining. NORM wastes can be treated in a VacuDry® unit in order to prepare it for a safe sub earth disposal. Find more information, important key facts and the benefits of VacuDry® NORM waste plants on http://www.econindustries.com/applications/norm-waste

Mercury Waste

by econ industries GmbH     based in Starnberg, GERMANY

Mercury-contaminated wastes are a major challenge for many industries including the chlorine industry, oil & gas drilling, oil & gas refineries (catalysts) and fluorescent lamps recycling. Due to strict legal restrictions and HSE requirements, mercury-contaminated waste is required to be handled with special care. We at econ industries have the best solution for each specific mercury waste stream, with plants that are recognised as being state of the art from approval authorities worldwide. Find more information an the benefits of VacuDry® mercury waste plants on http://www.econindustries.com/applications/mercury-wastes

Waste to Energy

by Babcock & Wilcox MEGTEC     based in De Pere, WISCONSIN (USA)

We can treat the air streams from waste management plants, MBT (Mechanical Biological Treatment) reception and composting areas, Waste Water Treatment Plants (WWTP), Refuse Derived Fuel (RDF) Plants, gasification of waste, syngas, torrefaction, gas engines and biogas upgrading. In waste management plants and WWTP, we remove the odors that may be causing a nuisance to neighbors, with bioreactors using Biomass to degrade odorous components and where odors are particularly intractable or VOC emissions higher, thermal oxidizers to meet prescribed emission limits and odor levels. In RDF Plants, Syngas, Gasification, Gas Engine and Biogas Upgrading applications, we employ thermal oxidizers, particulate removal and DeNOX systems, for the control of VOC, NOx, CO and particulates to prescribed emission limits.

Biofiltration

by AquaBiotec     based in Paris, FRANCE

Biological Aerated Upflow Filtration (BAF) for high efficient Waste Water Treatment in Refinery Industry with more than 20 reference plants and more than 20 years of experience

Flaring Solutions for the Upstream Oil & Gas Industry - Tank Batteries/Storage Tanks

by ABUTEC LLC     based in Kennesaw, GEORGIA (US) (USA)

The EPA mandates that all upstream oil and gas operators install factory-certified combustors that meet new Quad O compliance standards, or perform field testing on the flare system post-installation. ABUTEC offers the only compliance-ready combustors available to the market, making expensive testing no longer necessary for our customers. The use of enclosed combustors is an integral piece of the extraction process and affords companies the opportunity to operate in extreme conditions while still maintaining low emissions and following Quad O regulations.

Gas Sensing for Gasification

by Edinburgh Instruments Ltd     based in Livingston, UNITED KINGDOM

Syngas (short for synthetic gas) can be burnt and used as a fuel source, the main constituents of syngas are Carbon Monoxide (CO) and Hydrogen (H), which amount for around 85% of Syngas, and it is produced by a process called Gasification. Gasification starts with a base material which can originate from a wide variety of materials for example wood chips and pellets, plastics, municipal solid waste, sewage, waste crops, and fossil fuels such as coal. During Gasification the base material is reacted at high temperature without combustion with controlled amounts of oxygen (O) or steam. The composition of the base material combined with the amount of oxygen and heat used in the process affects the composition of the resultant SynGas, in which the CO can vary between around 20 and 60%. In addition, large amounts of H and CO are also formed. The measurement of CO is therefore an important feature in the production of SynGas.

Very large waste gas volumes with low contaminant concentration

by Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control     based in Graz, AUSTRIA

The CTP desorption allows for an especially high concentration factor which, in turn, reduces the cost of ownership and permits an auto-thermal operation (additional burner switched off) even when the contaminant concentration is low.

Thermal waste gas purification of siliceous organic compounds

by Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control     based in Graz, AUSTRIA

The cleaning problem of the heat exchangers was solved. The contaminants were destroyed efficiently and economically while steam for the production process was generated at no additional cost.

Waste gas treatment for the TFT industry

by DAS Environmental Expert GmbH     based in Dresden, GERMANY

Manufacturing TFT/LCD displays requires waste gas treatment as well. Processes that produce large scale Thinfilm Transistors (TFT) on glass substrates, for instance, use Chemical Vapour Deposition – CVD – to separate the thin films onto the material. The process requires cleaning the process chamber periodically and usually employs etching with NF3. Etching of the separated thin films typically utilises CF4, SF6 and chlorinated gases, which release large amounts of waste gas mixtures.

Need help finding the right suppliers?

Let the XPRTs do the work for you