Cone Penetrometers Equipment For Monitoring And Testing Available In Hawaii
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The 200 kN CPT crawler is a CPT penetrometer rig based on a crawler undercarriage. The rig has been designed to execute soil mechanical research based on static Cone Penetration Testing (CPT) techniques in an efficient manner. By means of the penetrometer pusher, installed in the center of gravity of the CPT crawler, either an electrical or mechanical probe (called a cone) is pushed into the ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The CPT crawler-truck is a CPT penetrometer rig based on a truck-chassis provided with a crawler undercarriage. The crawler-truck has been designed to execute soil mechanical research based on static Cone Penetration Testing (CPT) techniques in an efficient manner. By means of the penetrometer pusher, installed in the centre of gravity of the CPT crawler-truck, either an electrical or mechanical ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The hand pulled dynamic penetrometer rigs of the LMSR series are either driven by a gasoline engine, an electric motor or by a hydraulic ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The CPT truck is a CPT penetrometer rig based on a truck-chassis. The CPT truck has been designed to execute soil mechanical research based on static Cone Penetration Testing (CPT) techniques in an efficient manner. By means of the penetrometer pusher, installed in the centre of gravity of the CPT truck, either an electrical or mechanical probe (called a cone) is pushed into the ground and the ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The 200 kN stand-alone CPT penetrometer set is a lightweight and economical rig with full Cone Penetration Testing (CPT) capabilities. It is suitable for both electrical and mechanical CPT ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
Purposely designed rig for working inside buildings. The short-stroke 200 kN pusher is provided with a built-in push-and-pull clamp and powered by a 400 Vac electric-hydraulic power-pack. Standard 1000 mm long CPT tubes are ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The CPT push-and-pull clamp is purposely designed for automatic pushing and pulling of CPT sounding tubes (Ø = 36 mm) and casing tubes (Ø = 55 mm) during electrical CPT testing ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
The hand penetrometer for top layers is a device that is used to determine the penetration resistance of top layers. Because of the limited overall length of the device, the hand penetrometer can also be used for horizontal measurement, for instance in the walls of profile ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The sounding rods are used during Dynamic Penetration Testing (DPT) and Standard Penetration Testing (SPT) to hammer the sounding tips into the ground by means of a dynamic penetrometer rig. Gouda-Geo DPT and SPT sounding rods meet the highest quality standards. The rod material is manufactured by one of Europe’s leading steel manufacturers according to our own “Gouda-Geo” ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
The "pocket penetrometer" is specifically used to determine the penetration resistance of top layers (measuring depth 5 mm) and of samples in the field or in the laboratory. Measuring range 0.5 MPa. When pushing the instrument into the ground, the pin encounters a force of the ground. The spring is compressed by this force. A slip ring is taken along during this operation, which shows on the ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
Nearshore cone penetration testing is not as difficult as it might seem. In case of nearshore CPT (also referred to as over-water or marine CPT) the specifications of the equipment, the operation and the procedures to follow differ slightly from land testing. It is for reason recommendable to opt for a CPT penetrometer rig that has been purposely designed for this ...
-
PremiumManufactured by AMS, Inc.based in USA
Geotester dial penetrometer set is used for on-site measurement of soil compaction by testing the foundation plane or boring samples. It gives readings of estimated unconfined compressive strength in TSF or kg/cm2 when used with the standard 1/4' dia plunger. The geotester is furnished with stainless steel plungers, carrying case, data tables, register plates and ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
Piezometer standpipes are tubes with a perforated part, which is placed in the ground in order to determine the groundwater level (i.e. the phreatic water table) or to monitor the quality and quantity of the groundwater. You can find the best piezometers for measuring groundwater levels at Gouda ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The CPT truck is a CPT penetrometer rig based on a truck-chassis. The CPT truck has been designed to execute soil mechanical research based on static Cone Penetration Testing (CPT) techniques in an efficient manner. By means of the penetrometer pusher, installed in the centre of gravity of the CPT truck, either an electrical or mechanical probe (called a cone) is pushed into the ground and the ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
Measure excess pore pressure that is generated during soil penetration with our digital CPTU piezocone testing system. In the quotations, Gouda Geo-Equipment issues a clear distinction is made between on one hand the CPT penetrometer pusher (this could either be a truck-based, crawler-based, trailer-based or stand-alone unit) and on the other hand the CPT system (this could either be mechanical ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
When performing CPT tests over water or in very soft soils, the use of a catching clamp is very much recommended. It holds the CPT sounding tubes or casing tubes when they are not gripped by a clamp or pulling ...
-
PremiumManufactured by AMS, Inc.based in USA
Developed by the Army Corps of Engineers, Dynamic Cone Penetrometers (DCPs) provide a low-cost, efficient test method for quickly determining in-situ CBR values of pavement base, subbase and subgrades. They can readily be used for depths up to 30" and up to 6' with optional drive rods and extensions. This model complies with ASTM D6951 specifications and comes with a chart to compute CBR values, ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The closed soil sampling tubes are made of high-quality steel and designed such, that they can accommodate a transparent PVC liner for holding the soil sample. The inner diameter of the liner is 48 mm, the outer diameter is 50 mm. The cutting shoe is detachable by means of a screw connection enabling the appliance of a core ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
Hand penetrometer Eijkelkamp, standard design, for measurements to a depth of 3 ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The window sampling tubes are made of high-quality steel and features multiple windows making visual inspection of the samples easy and straightforward. The cutting shoe (made of hardened steel) is detachable by means of a screw connection enabling the appliance of a core ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you