Only show results in Virginia? Ok

Continuous Emissions Monitoring (CEMS) Applications

  • Premium

    Continuous emissions monitoring in waste incineration plants

    Waste-to-energy through incineration of waste is an effective way of producing electricity and heat, at the same time getting rid of the possibly hazardous or unrecyclable waste. The waste can be incinerated at specific WtE plants or at plants with permission for co-incineration of waste at biomass boilers or cement kilns. The waste incineration plants are, however, governed by strict emissions regulations.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Fluoride emissions monitoring in aluminum smelters

    Production of aluminum from its ores at aluminum smelters results in carbon dioxide CO2, carbon monoxide CO, sulfur dioxide SO2, and hydrogen fluoride HF gas emissions during the electrolytic process phase to the atmosphere. The gas emissions need to be monitored. Typically the smelters have emission limit values (ELVs) for sulfur dioxide and hydrogen fluoride emissions. These emissions should be measured accurately and with good precision, to ensure the smelter does not exceed its emission limit values. In...

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Air quality and industrial gas monitoring systems for CEMS - Stack air monitoring

    Continuous Emissions Monitoring Systems (CEMS) are used to measure flue gases from stationary sources at a wide variety of regulated industrial facilities, including power plants, petroleum refineries, petrochemical plants, waste incinerators, pulp and paper producers, and many others. The types of air pollution measured from these sources vary widely based on the industry and process, and many are regulated by government agencies around the world.

    By Teledyne API based in San Diego, CALIFORNIA (USA).

  • Premium

    Continuous emissions monitoring in cement kilns

    Various pollutants form in the cement manufacturing process, especially when alternative fuels and waste-derived fuels are used. Typically a cement kiln using these fuels is a required to monitor hydrogen chloride (HCl). Gasmet CEM II is EN 15267-3 approved for HCl measurement in 0 … 15 mg/Nm3 range.High process temperatures result in generation of more nitrogen oxides (NOx) than in typical municipal waste incineration.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Monitoring solutions for the continuous emissions monitoring

    Multi-gas Stack Analyzers for Continuous Emissions Monitoring. FTIR and UVDOAS Analyzer Models available for Insitu Probe, Internal or External Cells, or Cross Stack Sample Acquisition.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Continuous emissions monitoring for sulphuric acid production plants

    The process control of a sulphuric acid plant needs good and reliable detection of gas phase sulphur dioxide (SO2). To measure SO2 is a challenge due to the corrosive environment and high concentration of SO2. Several places in the process needs to be monitored and to transport the sample gas is difficult. A large dynamic range is needed as the SO2 concentration can vary between 15% volume and a few mg/m3. Most systems installed need a lot of maintenance, sometimes as often as every day.

    By Opsis AB based in Furulund, SWEDEN.

  • CO2 / CO Monitoring in Air

    CO (carbon monoxide) and CO2 (carbon dioxide) are generally measured to ensure process control. CO2 is the desired product and CO is undesired in combustion since it will explode in high enough concentrations. CO2 and CO concentrations can also be used to determine other process-specific efficiencies. Continuous emissions monitoring equipment that can be calibrated as a CO and CO2 analyzer is thereby essential for process control.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Gas monitoring and dust monitoring

    EM-5 series Continuous Emission Monitoring System (CEMS) Counting tail gas emission and realtime concentration NOX SO2 O2 Temperature pressure flow dust

    By HANGZHOU ZETIAN TECHNOLOGY CO., LTD based in Hangzhou, CHINA.

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • O2 Monitoring in Air

    Oxygen (O2) is a colorless odorless gas, essential to all life on Earth but damaging in high concentrations. An O2 analyzer should thus be employed for safety management and air pollution prevention purposes. LasIR MP110 is perfect for continuous emission monitoring of O2. It is based on TDLAS technology and can be calibrated as an O2 analyzer, providing accurate and reliable measurements. It quickly responds to changes in compound concentration, thus providing continuous emission monitoring for the specified gas.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Continuous Emissions Monitoring

    Requirements for monitoring emissions to air are governed by EU/UK legislation and are implemented in the form of a permit by the Environment Agency or local authority. The Dr Foedisch muti-component gas analysers continuously extract a gas sample from the exhaust stream via a stack probe into the analyser cabinet. Both hot and cold gas systems are available, please contact us to discuss which system best suits your requirements.

    By CEM Solutions (UK) Ltd. based in Darley Dale, UNITED KINGDOM.

  • Continuous Emission Monitoring

    By MRU Instruments, Inc. based in Houston, TEXAS (USA).

  • Laser Dispersion Spectroscopy Technique for Process Industries

    Accurate, dependable real time results in harsh environments. Industrial processes typically result in some of the most challenging gas measurement environments; high-temperature, high humidity, particulate matter, and gas mixtures of complex and variable composition.

    By Mirico based in Chilton, UNITED KINGDOM.

  • Continuous emissions monitoring for mining industry

    Opsis non-contact monitoring solutions are very well suited for applications in the mining Industry, as the flue gas conditions often involve high temperature and high dust concentrations.

    By Enviro Technology Services Ltd based in Stroud, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you