Continuous Emissions Monitoring (CEMS) Applications available in Newfoundland
-
Premium
Continuous emissions monitoring solutions for palm oil plants
Make more out of your mill. OPSIS tested and approved monitoring systems provide cost-effective and reliable on-line monitoring of several gas compounds, such as both high and low concentrations of methane, moisture, carbon dioxide and hydrogen sulphide, at several ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Continuous emissions monitoring for aluminium smelters
Process control and emissions monitoring in an aluminium smelter is a challenge due to the high concentrations of HF. To use an extractive system in this environment will demand a lot of ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Continuous emissions monitoring for sulphuric acid production plants
The process control of a sulphuric acid plant needs good and reliable detection of gas phase sulphur dioxide (SO2). To measure SO2 is a challenge due to the corrosive environment and high concentration of SO2. Several places in the process needs to be monitored and to transport the sample gas is difficult. A large dynamic range is needed as the SO2 concentration can vary between 15% volume and a few mg/m3. Most systems installed need a lot of maintenance, sometimes as often as every ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Continuous emissions monitoring solutions for waste to energy plants
Process control and emission monitoring in a waste to energy plant is a challenge. A large number of gaseous components need to be measured with high accuracy. Almost 100% uptime is required and the monitoring system needs to be easy to maintain and fast to calibrate. The OPSIS system is tested and approved to have the best performance and longest calibration intervals, and provides the waste to energy plant with an accurate analyser that will operate with a minimum of ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Fully-automated gas chromatographs solutions for stack emissions monitoring sector
Synspec GCs can also be used as continuous emission monitoring systems (CEMS). In general, emissions from stacks are in the higher ranges of concentrations to be measured. Synspec equipment, which is usually geared towards very low detection levels, can be tuned to the concentration ranges that are emitted at your production plant. Depending on the composition of the emissions a sample treatment might be ...
By Synspec BV based in Groningen, NETHERLANDS.
-
Premium
Continuous emissions monitoring for cement industry
Process control and emissions monitoring in cement plants, can be a challenge due to the dusty and corrosive environment. OPSIS provides an accurate system that will operate with high performance and a minimum of ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Gas monitoring and dust monitoring
EM-5 series Continuous Emission Monitoring System (CEMS) Counting tail gas emission and realtime concentration NOX SO2 O2 Temperature pressure flow dust ...
By Hangzhou Chunlai Technology CO., Ltd. based in Hangzhou, CHINA.
-
Premium
Gas analyzers and monitoring systems for Raw gas measurements
Raw gases are untreated flue gases that have not passed through an emissions control technology system like selective catalytic reduction (SCR) or selective non-catalytic reduction (SNCR). They are generally measured for the sakes of process control and warranty tracking. Typically only a few components are measured but fourier transform infrared spectroscopy FTIR technology allows the measurement of all ...
By Gasmet Technologies - a Nederman company based in Vantaa, FINLAND.
-
Premium
Continuous emissions monitoring solutions for mercury monitoring
Waste incinerators, cement plants and power plants need good and reliable measurements of total gaseous mercury. The measurement of total gaseous mercury is a challenge due to chemical reactions and contamination. The installed systems will often require a lot of maintanence still not giving reliable ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Continuous emissions monitoring for glass manufacturing industries
Process control and emissions monitoring in a glass manufacturing plant is a challenge due to high temperature in the flue gas. The OPSIS DOAS system provides the glass industry with an accurate analyser that will operate with a minimum of maintenance. The OPSIS DOAS system is based on a non-contact method that uses an optical path to measure across the duct. A single OPSIS system will measure all relevant gas componensts such as NOX, SO2, CO, CO2, H2O, O2, and ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Waste Incineration Application Note
Waste incineration is commonly used to dispose of the organic components of both domestic refuse and hazardous waste by burning it under controlled conditions. The heat generated in this process can be used to generate electricity, a process known as Waste-To-Energy (WTE). Because they have the potential to release highly toxic chemicals, such as polyaromatic hydrocarbons (PAH) and heavy metals, waste incinerators are subject to stringent environmental regulations.Temperature and emissions monitoring equipment ...
By AMETEK Land Instruments International Ltd based in Dronfield, UNITED KINGDOM.
-
Premium
Continuous emissions monitoring solutions for power plants
OPSIS offers fully automated system solutions for continuous monitoring in power plants. The monitoring systems have been tested and approved by the German TÜV and the U.S. EPA among others, for the best performance and longest calibration ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Gas monitoring instruments and systems for process NOx measurement
Nitric acid HNO3 is an important intermediate reagent for production of several important end products, such as fertilizers, explosives, dyestuffs/pigments, pesticides, pharmaceuticals, photographic materials, plastics, and synthetic fibers. At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. A single system can be used to measure the high levels of nitrogen monoxide NO and nitrogen ...
By Gasmet Technologies - a Nederman company based in Vantaa, FINLAND.
-
Premium
Gas monitoring instruments and systems for nitric acid process
Modern production method of nitric acid production may lead to generation of several different gaseous emission components, such as nitrogen oxides (NOx), ammonia NH3 and nitrous oxide N2O. Nitrogen monoxide is an intermediate gaseous product in manufacturing of nitric acid HNO3. NO is formed in a catalytic reaction between ammonia and molecular oxygen O2. But undesirable side reactions may result in formation of nitrogen dioxide NO2 and nitrous oxide N2O. The NO and NO2 emissions can be reduced by use of ...
By Gasmet Technologies - a Nederman company based in Vantaa, FINLAND.
-
Premium
Gas monitoring instruments and systems for stack testing
Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives ...
By Gasmet Technologies - a Nederman company based in Vantaa, FINLAND.
-
Premium
Continuous emissions monitoring solutions for H2S monitoring
To monitor H2S can be difficult. The UV absorption is without structure and the IR absorption has strong interference from H2O. The traditional way has been to remove all SO2 from the sample while keeping H2S, then convert H2S to SO2 ,and finally measure SO2 which then effectively yields the H2S concentration. The instruments used have often been ambient air SO2 analysers and extractive dilution systems. However, it is not unusual to experience practical problems with these type of ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Emissions Monitoring for Mining / Emissions Monitoring for Smelting
The Opsis monitoring solution for mining and smelting applications is based on either DOAS or laser diode technique. Opsis non-contact monitoring solutions are very well suited for applications in the Mining and Smelting Industries, as the flue gas conditions often involves high temperatures and high dust concentrations. The on-line, open-path systems are used for monitoring HF, sulphur dioxide, SO3 and HCl in potrooms, in fence-line applications and in continuous emissions ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Continuous emissions monitoring solutions for mineral wool production
Process control and emissions monitoring in a mineral wool plant is a challenge due to the presence of phenol and formaldehyde. To use an extractive system in this environment will demand a lot of maintenance. The OPSIS DOAS system is different and provides plants with an accurate analyser that will operate with a minimum of maintenance. The OPSIS DOAS system is based on a non-contact method using an optical measurement path that can operate across the ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Continuous emissions monitoring solutions for fertilizer industry
Process control and emissions monitoring in a fertilizer plant is a challenge due to the high concentrations of HF. To use an extractive system in this environment will demand a lot of ...
By OPSIS AB based in Furulund, SWEDEN.
-
Premium
Gas flow management solutions for standard applications sector
Standard Applications of Gas Flow ...
By Environics, Inc. based in Tolland, CONNECTICUT (USA).
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you