Engine Emissions Monitoring Downloads

Filter Weighing for Emission Determination Fast Results for the Automotive IndustryFilter Weighing SolutionSmart filter handlingThe innovative filter holder allows acclimatization, storage, transport and weighing all in one, without filter removal and any interruption.High throughputThe automated process speeds up the weighing time of 60 filters down to 60 minutes while keeping the ...

Dec. 26, 2014

By Mettler - Toledo Int. Inc

Introduction The mercury concentration in crude oil and petroleum products can vary in a wide range of less than 0.1 ppb to dozens ppm. Direct mercury determination in crude oil and petroleum products at the range above 5 ppb is covered by ASTM D7622-10(2015) "Standard test method for total mercury in crude oil using combustion and direct cold vapor atomic absorption method with Zeeman background ...

Mar. 19, 2018

By Lumex Instruments Group

The TunnelTech 502 NO sensor, is an essential part of any road or rail tunnel safety system. Firstly, it monitors the atmosphere within the tunnel and ensures that the tunnel ventilation system provides sufficient clean air to protect tunnel users health. Nitric Oxide is a colourless, poisonous and oxidising gas with an irritating odour and is product of vehicle engines. Small levels of NO can ...

Jun. 4, 2016

By Codel International Ltd

> Automotive:Real-time vehicle exhaust analysisMonitoring of combustion enginesVolatile organic compounds (VOCs) and their atmospheric photochemical reaction products have lately drawn much attention due to their negative impact on the atmosphere and their dangers to public health.PTR-MS is an analytical technique to quantify hydrocarbons and VOCs with high sensitivity and in real-time.The ...

Aug. 24, 2015

By Ionicon Analytik Ges.m.b.H.

Flexibility, reliability and performance: Acme sensors profit from years of field experience making them among the most flexible within the gas detection industry. All products are tested extensively and provide unparalleled levels of ...

Aug. 20, 2014

By Acme Engineering Prod. Ltd.

Sierra’s Automatic Filter Changer is a compact and portable safety and automation tool that should be a part of every emissions test cell. The system allows the engineer to stay out of the test cell during testing so several tests can be done in succession. The system typically holds either 12 or 15 single or double filter cartridges, but can be made to accommodate as many as 22 cartridges. ...

May 13, 2011

By Sierra Instruments, Inc.

The Sierra Instruments Soot-Trak™ laser measures real-time engine soot particle mass emissions and performs characterization of soot particle size, primary particle surface area and number. Soot-Trak provides researchers and engine developers the accurate information they require about particle transport. With measurement accuracy of 5% using a known calibration source, Soot-Trak also sets ...

Oct. 5, 2010

By Sierra Instruments, Inc.

A Company from Strong Roots The Enmet Canada series of gas detection is a product division of Arjay Engineering. Enmet gas detection design and manufacturing extends back to ...

Mar. 30, 2017

By Arjay Engineering Ltd.

Flexible monitoring and control for ventilation of Carbon Monoxide, Nitrogen Dioxide and Propane gas in apartment buildings, office and commercial buildings, public parking facilities and maintenance garages. The Arjay/Enmet Canada series 4300-PG is a complete gas monitoring system from Arjay Engineering Ltd.. Over 40 years of gas detection experience has contributed to this ...

Mar. 29, 2017

By Arjay Engineering Ltd.

What is fuel dilution and why is it a problem? Fuel dilution in oil is a condition caused by excess, unburned fuel mixing with engine oil in an engine crankcase. Hydrocarbon-based fuel, usually with a lower vapor pressure than the lubricant, has a thinning effect, lowering the oil viscosity. Oil film strength is reduced, increasing the cylinder liner and bearing wear. Reciprocating engines ...

Mar. 4, 2017

By Spectro Scientific

The InfraCal 2 Soot Meter complies with ASTM D7686 method for measuring soot in in-service lubricants. Soot is an important oil and engine condition indicator. More stringent emission requirements as well as saving costs with extended drain times make it more important than ever to routinely check soot levels. Infrared spectroscopy is a well-established laboratory method for testing used ...

Mar. 1, 2017

By Spectro Scientific

Established in 1978, Environnement S.A is a market leader in continuous environmental pollution measurement systems and monitoring solutions for process optimisation: Ambient air quality monitoring (AQMS), Continuous emission monitoring (CEMS), Industrial process measurement (IPMS), Engine exhaust gas monitoring (EGAS), Radionuclide monitoring (RNMS), Environmental Data Acquisition & ...

Dec. 22, 2016

By Environnement S.A Group - envea

When extracting and refining valuable geological materials from the earth (eg. limestone, aluminum oxide, gold), a variety of industrial combustion processes are required. The machinery used in these processes such as industrial engines, boilers, and smelters can emit highly toxic gases that are harmful to the environment and to human life. Using a portable emissions analyzer enables mining ...

Jul. 8, 2016

By E Instruments International, LLC

CEMS are fixed units that typically only measure from one sample location which is usually on a main centralized stack. This main stack is often fed by several separate emissions sources throughout the plant such as boilers, heaters, engines, ovens, and furnaces. If the CEM is measuring emissions that are higher than the regulated or permitted limits, it can be difficult to determine the source ...

Jul. 8, 2016

By E Instruments International, LLC

There are many types of stationary and mobile internal combustion engines that can run off gas or diesel fuels. Engines can be lean burning at a high air to fuel ratio (AFR) or rich burning at a low AFR. The exhaust stack gases from engines contain pollutant gases including CO, NO, NO2, NOx, and CxHy hydrocarbons as well as particulate matter. Measuring the engine exhaust emissions is important ...

Jul. 8, 2016

By E Instruments International, LLC

Cogeneration, or combined heat & power (CHP), is the utilization of boilers, turbines, and/or engines to simultaneously generate electricity power and heat that can be useful in several ways such as for hot water, steam, district heating, and water ...

Jul. 8, 2016

By E Instruments International, LLC

Many forklift trucks have internal combustion engines that burn propane, natural gas, diesel, or other fossil fuels. A portable combustion gas and emissions analyzer can be used to optimize combustion efficiency & maximize fuel savings, identify and quantify sources that can adversely affect safety and comfort in the work environment, and measure and reduce harmful emissions in the forklift ...

Jul. 8, 2016

By E Instruments International, LLC

Measure Exhaust Gases From Marine Diesel Engines For Compliance with MARPOL Annex VI & NOx Technical ...

Jul. 7, 2016

By E Instruments International, LLC

Hand-Held Versatile Gas Analyzer for Emissions Monitoring of Boiler, Engine, Furnace, and Other Combustion ...

Jul. 7, 2016

By E Instruments International, LLC

Transportable Emissions Analyzer for Boiler, Engine, Furnace, Kiln, and other Combustion ...

Jul. 7, 2016

By E Instruments International, LLC