EPA Methods Applications available in Spain

  • Premium

    Determination of the total mercury in a filtrate of wash-off samples from contaminated surfaces

    INTRODUCTION

    Quantitative determination of the total mercury content in filtrates of wash-off samples from the surfaces of walls, floors, equipment, and other facilities of m anufacturing areas is an effective method for the occupational safety monitoring.

    By Lumex Instruments Group based in Mission, BRITISH COLUMBIA (CANADA).

  • Premium

    Direct mercury determination in coal

    Introduction

    Mercury is one of the most toxic trace contaminant naturally occurring in the coals. During the coal combustion process at the coal-fired power plants mercury is released into the environment. To manage effectively the stack gas cleaning process, it is necessary to know the mercury content in the coal, and also in stack gas, liquid and solid wastes.

    By Lumex Instruments Group based in Mission, BRITISH COLUMBIA (CANADA).

  • Premium

    Determination of inorganic anions in aqueous matrices according to EPA 6500 and ASTM D6508-10 test methods

    This test method is applicable for determination of the dissolved inorganics anions; fluoride, bromide, chloride, nitrite, nitrate, ortho-phosphate, and sulfate in aqueous matrices using capillary ion electrophoresis with indirect UV detection. The method can be applied to drinking water, wastewater and ground water. 

    By Lumex Instruments Group based in Mission, BRITISH COLUMBIA (CANADA).

  • Premium

    RAPID ANALYSIS OF TOTAL MERCURY IN WASTE WATERS AND PROCESS WATERS WITH ELEVATED MERCURY CONTENT USING DIRECT PYROLYSIS TECHNIQUE

    A conventional standard method of total mercury determination in water using atomic absorption spectrometry (AAS) involves preliminary sample digestion that takes from 30 minutes to 8 hours depending on the digestion conditions. The use of a mercury analyzer RA-915M/RA-915+ with Zeeman background correction in combination with PYRO-915+ pyrolysis attachment provides direct determination of mercury in process and waste waters contaminated with mercury without digestion or any other sample preparation stages. The...

    By Lumex Instruments Group based in Mission, BRITISH COLUMBIA (CANADA).

  • Premium

    Analysis of VOC compounds in water by Purge & Trap or dynamic headspace

    Context & Challenges Volatile organic compounds (VOC) can be dissolved in water. Sometimes water is polluted and to study contamination of VOC in finished drinking water, VOC must be measured. Chromatotec® Solutions Chromatotec® has developed a specific system for the measurement of VOC in water: a Purge & Trap system, the airmoPURGE. The analyzer is coupled with a degasing system allowing the extraction of dissolved gases. The complete system is based on: - 502.2 method from US EPA –...

    By Chromatotec Group based in Val de Virvée, FRANCE.

  • Premium

    Gas monitoring instruments and systems for stack testing according to EPA test method 320

    The United States Environmental Protection Agency (EPA) has two stack testing methods for FTIR gas analyzers. Method 320 is an FTIR method for measuring wide range of organic and inorganic pollutants. Method 321 is a specific version for measuring hydrogen chloride HCl at cement kilns producing Portland cement. These methods define a quality assurance and control processes for verifying the accuracy of the results. The requirements for analytical equipment and software are defined on 40 CFR Part 60 Appendix B...

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Ultraviolet disinfection systems for the USEPA UVDM validation

    For drinking water applications, atg UV Technology`s independently 3rd party validated UV systems are sized to deliver both 40 mJ/cm2 RED UV Dose, or a 3 log (99.9%) to 5 log (99.999%) reductions of Cryptosporidium. As a leading testing and validation protocol, the United States Environmental Protection Agency (US EPA) Ultraviolet Disinfection Guidance Manual (UVDGM) 2006 provides an advanced testing and validation method for guaranteeing UV disinfection performance for a large range of operating conditions,...

    By atg UV Technology based in Wigan, UNITED KINGDOM.

  • Particulate monitoring for continuous emissions

    With the advent of specific process emission limits being defined, continuous particulate monitoring has become a regulatory requirement for many industries. smoke stack #1Particulate monitoring requires the measurement of the mass concentration of particulate matter in stack emissions to atmosphere. There is no known method of continuously measuring particulate concentration by direct measurement and therefore, all continuous particulate measurement methods are inferential. Each method involves the measurement...

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Gas Detection and Analysis Equipment for Chemical and Petrochemical

    In a complex petrochemical facility there may be many thousands of potential leaks paths. Some may be leaking but most will not. Using an infrared Gas Detection camera allows the user to examine many potential leaks sources in a short time and from a distance. The EPA acknowledged gas imaging cameras, such as Opgal’s EyeCGas®, as an approved Leak Detection and Repair (LDAR) Method 21 alternate work practice (AWP).

    By Opgal Optronic Industries Ltd. based in Karmiel, ISRAEL.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you