Insertion Flow Meters Equipment For Monitoring And Testing Available In Bolivia
-
PremiumManufactured by Fluid Components International LLC. (FCI)based in USA
The Model ST50 is a compact, low cost solution for accurate, repeatable flow rate measurement of air, compressed air or nitrogen. This insertion-style flow meter has no moving parts and is available in probe lengths for installation into pipe diameters from 2.5 inches to 24 inches [63 mm to 610 mm]. It is easily connected into the pipe via a 1/2 inch or 3/4 inch NPT compression ...
-
PremiumManufactured by VPInstrumentsbased in NETHERLANDS
The hot tap drill is the universal tool to install your insertion flow meter in any compressed air system. In only 30 minutes you can drill a hole and install your flow meter. Using a hot tap saddle and a hot tap drill, you can create a new installation point without depressurizing your ...
-
PremiumManufactured by VPInstrumentsbased in NETHERLANDS
The VPFlowScope Probe is the number one measurement tool for compressed air audits and fixed installations. You can combine the probe with two display module types or a connector cap without display. With the VPFlowScope Probe you can measure virtually any compressed air system using a single ...
-
PremiumManufactured by VPInstrumentsbased in NETHERLANDS
With the VPFlowScope® M you are ready for the future. This next-generation flow meter is Industry 4.0/IOT ready. Next to 4 .. 20 mA and RS485 (Modbus RTU), it also has a built-in Ethernet (Modbus/TCP) interface, making it easy to connect directly to any network. It can be installed under pressure and measures (bi-directional) thermal mass flow, pressure, temperature and total flow ...
-
PremiumManufactured by VPInstrumentsbased in NETHERLANDS
The VPFlowScope M is a 4-in-1 insertion flow meter for compressed air and technical gases. It can be installed under pressure and measures bi-directional flow, pressure, temperature, totalized flow simultaneously. The VPFlowScope M is the next step in gas measurement. You are industry 4.0 ready, with the additional Ethernet output. With the VPFlowScope M re-calibration is history: simply exchange ...
-
PremiumManufactured by VPInstrumentsbased in NETHERLANDS
The VPFlowScope® DP is the ultimate measurement tool for saturated compressed air flow measurements. The unique design enables you to take measurements in the discharge pipe of a compressor under 100% saturated conditions. You can combine the probe with two display module types or with a connector cap without ...
-
Manufactured by Hydreka SA - A Halma Companybased in FRANCE
Hydraulic test bench for insertion probes and transit flowmeters. Creation and edition of calibration certificates Ideal training equipment for your teams. Product maintenance Flowmeter calibration ...
-
Manufactured by Electronet Equipments Private Limitedbased in INDIA
Electronet series ELMAG - 100S are microcontroller based two / four wire insertion type electromagnetic flow meters which measure the flow rate in a completely filled pipe by monitoring the voltage produced when the (conductive) liquid moves through a magnetic field. The meter is available in non-corrosive material which provides long term reliability with less maintenance cost. This simple to ...
-
Manufactured by Adept Fluidyne Pvt. Ltdbased in INDIA
Electromagnetic Flow measurement has been in use around the world for 50 years and more, as witnessed by the popularity of these meters that continues unabated in virtually all sectors of industry. Electromagnetic Flowmeters can be used to measure all electrically conductive liquids (> 5 µS/cm) with or without solids, e.g. water, wastewater, sludge, slurries, pastes, acids, alkalis, ...
-
Manufactured by FLOW-TRONIC S.A.based in BELGIUM
The TORPEE-MAG is a hot tap full profile electromagnetic insertion flowmeter. Multiple electrodes placed across the entire sensor body at equal area, measure and report the average flow rate over the full diameter of the pipe. The specific design of the multi-electrode sensor compensates for variable flow profiles, including swirl and turbulent conditions and allows installation without ...
-
Manufactured by ABB Measurement Productsbased in SWITZERLAND
Aquaprobe is an economic alternative to full bore flow meters. It comprises an electromagnetic sensing head mounted on the end of a support ...
-
Manufactured by YSI Incorporated - a Xylem brandbased in USA
The EX81 is an insertion electromagnetic flowmeter for use with conductive liquids in pipe sizes 1 to 3 inches. The EX82, Insertion Magmeter, is for use with pipe sizes 4 to 10 inches. The EX83, Insertion Magmeter, is a stainless steel electromagnetic flowmeter designed for use with pipes 12 inches in diameter. With no moving parts, the insertion electromagnetic flowmeter is highly suitable for ...
-
Manufactured by Eldridge Products, Inc. (EPI)based in USA
Insertion style thermal mass flow meters include a sensor & probe assembly that is inserted into the process gas flow conduit to allow the process gas to flow across the flow sensing elements. Our insertion style flow meters are available with 3/4″, or 1″ OD probes. Tube fittings and ball valve retractor assemblies, with or without a mounting flange, are also available from the ...
-
Manufactured by Eldridge Products, Inc. (EPI)based in USA
Inline style thermal mass flow meters include a flow section that is usually specified to match the user’s flow conduit and is then plumbed directly into the process line. This design has the sensing elements mounted directly in the flow section for exposure to the process gas. Our inline style thermal mass flow meters are available in sizes from 1/4″ pipe through 4″ pipe or ...
-
Manufactured by Manas Microsystem Pvt. Ltdbased in INDIA
Insertion Type Electromagnetic Flow Meter is an best solution for water flow measurements in immense diameter pipes. Most reasonably priced compared to its counterpart in full bore dimension or ultrasonic ...
-
Manufactured by SeaMetrics, Inc.based in USA
EXSOO-Series insertion electromagnetic flowmeters are designed for use with conductive liquids in 1 to 12' pipe. A choice of materials (stainless steel, brass, and PVC) allows the meter to adapt to a range of temperature, pressure, and corrosive environments. The EX800 is highly suitable for difficult applications with changing viscosities and pulsating flows, such as air-driven diaphragm pumps. ...
-
Manufactured by Eldridge Products, Inc. (EPI)based in USA
Inline style thermal mass flow meters include a flow section that is usually specified to match the user’s flow conduit and is then plumbed directly into the process line. This design has the sensing elements mounted directly on the flow section for exposure to the process gas. Our inline style flow averaging thermal mass flow meters are available in sizes from 2″ pipe through ...
-
Manufactured by Detectronic Ltdbased in UNITED KINGDOM
Designed to monitor raw sewage, industrial effluent and storm waters, the MSFM s2.5T ultrasonic water flow meter is self-contained and battery-powered. This ATEX insertion multi-sensor flow meter is suitable for applications in combined sewers, open channels and storm ...
-
Manufactured by Lanry Instrumentsbased in CHINA
Series DF6100-EI Doppler Insertion Ultrasonic Flow Meter can measure metal or plastic pipes with a certain amount of air bubbles or suspended solids. Advanced technique allows this instrument to operate with high reliability and low maintenance. Insertion transducers permit the instrument to be installed without interrupting system pressure or flow. ...
-
Manufactured by Sierra Instruments, Inc.based in USA
The QuadraTherm® 640i is the most accurate insertion-probe thermal mass flow meter for air / gas mass flow rate measurement on the market today, achieving gas mass flow rate accuracy never before possible, +/- 0.75% of reading above 50% of full scale. The QuadraTherm 640i air / gas mass flow meter marks an accuracy breakthrough in thermal dispersion technology achieving extreme precision with ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you