PM10 Particulate Monitoring Equipment For Monitoring And Testing Near Australia
-
Manufactured by AirMetricsbased in USA
Airmetrics manufactures the MiniVol TAS, which samples ambient air at 5 liters/minute for particulate matter (PM10, PM2.5, TSP). While not a reference method sampler, the MiniVol TAS gives results that closely approximate data from Federal Reference Method samplers. Lightweight and portable, the MiniVol TAS is ideal for remote areas or locations where no permanent site has been ...
-
Manufactured by AirMetricsbased in USA
The MiniVol TAS can be configured to sample for PM10 at a flow rate of 5L/min. The sampling procedures for PM10 are listed ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Enables heating of the Dekat® PM10 Impactor up to 200 ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
To remove humidity from the sample. 120 cm, 120 + 60 ...
-
PremiumManufactured by Apex Instruments, Inc.based in USA
PM10 is used for Method 201A testing and is designed for in-stack measurement of particulate matter equal to or less than 10 microns. The shank has a 5/8-inch outer diameter for easy adaptation to an in-stack 47-mm filter assembly or probe. The PM10 cyclone kit includes cyclone assembly, PM10 nozzle set, 47-mm filter assembly, and a carrying case. Kits are available in stainless steel or alloy ...
-
Manufactured by TSI Incorporatedbased in USA
Making ultrafine particle measurements in compliance with the CEN standards requires the right tools. TSI offers a full solution that includes sampling, drying, and diluting the aerosol, as well as measurement of relative humidity and temperature, particle number concentration, and particle size ...
-
Manufactured by HORIBA Europe GmbHbased in GERMANY
The APDA-371 automatically measures and records airborne particulate concentration levels (in milligrams or micrograms per cubic meter), using the industry-proven principle of beta ray attenuation. Thousands of this Dust Analyzer units are currently deployed worldwide, making the unit one of the most successful air monitoring platforms in the ...
-
Manufactured by Casella - TSI Incorporatedbased in UNITED KINGDOM
The Guardian2 Site Boundary Monitor is designed to help you remain compliant with site emission levels, using remote monitoring and reporting of noise, dust and vibration levels. Powered by mains, solar or battery, the Guardian2 is ideal for any construction noise monitoring or environmental dust measurement location, no matter how remote. For further details on solar or battery power options see ...
-
Manufactured by Casella - TSI Incorporatedbased in UNITED KINGDOM
The Guardian2 Site Boundary Monitor is designed to help you remain compliant with site emission levels, using remote monitoring and reporting of noise, dust and vibration levels. Powered by mains, solar or battery, the Guardian2 is ideal for any construction noise monitoring or environmental dust measurement location, no matter how remote. For further details on solar or battery power options see ...
-
Manufactured by TSI Incorporatedbased in USA
The DustTrak Environmental Aerosol Monitor is an air monitoring system built to house DustTrak photometer models 8540 or 8543. DustTrak's early detection features allow quick response to exposure concerns as PM10, PM1 and PM2.5. This system is built upon proven DustTrak technology that thousands of people use every day. It can be applied in the fugitive emissions monitoring, the fence-line ...
-
Manufactured by TSI Incorporatedbased in USA
The DustTrak II Aerosol Monitor 8530 is a desktop battery-operated, data-logging, single-channel, light-scattering laser photometer that gives you real-time aerosol mass readings and collects a gravimetric sample. It uses a sheath air system that isolates the aerosol in the optics chamber to keep the optics clean for improved reliability and low maintenance. It is suitable for clean office ...
-
Manufactured by Comde-Derenda GmbHbased in GERMANY
The low and medium volume samplers LVS and MVS collect fine particulate matter on sampling filters according to EN 12341:2014 (PM10 and PM2.5). For this purpose, a vacuum pump draws in ambient air, and the sampler fractionates the airborne fine particles in a sampling inlet. The air containing the desired fine particulate fraction then passes through the filter, where the particles are collected ...
-
Manufactured by Comde-Derenda GmbHbased in GERMANY
The PNS T-DM combines a low / medium volume sampler (LVS or MVS) and a filter changer in a stainless steel cabinet. It collects fine particulate matter on sampling filters according to EN 12341:2014 (PM10 and PM2.5). For this purpose, a vacuum pump draws in ambient air, and the system fractionates the airborne particles in a sampling inlet. The air containing the desired fine particulate fraction ...
-
PremiumManufactured by Apex Instruments, Inc.based in USA
PTFE-coated glass fiber filters are constructed from borosilicate microfibers and bonded with PTFE. The filters can be folded and handled without loss of fibers. Specifically recommended for Method 26, PM10, and PM2.5 sampling. Great for especially low loading rates and low absorption of acid gases such as SOx or NOx with at least 99.95% retention efficiency (0.3 μm DOP). ...
-
Manufactured by Comde-Derenda GmbHbased in GERMANY
The method applied by the APM-2 uses the light scattered by tiny particles (nephelometry) to determine the PM10 or PM2.5 concentration in the ambient air directly and continuously. After performing a qualification test, TÜV Rheinland certified the procedure as equivalent to the customary gravimetric method. The system features an impactor inlet for fractionating the particulate matter, and a ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
The Dekati PM10 Impactor is a three-stage cascade impactor for determining particle gravimetric mass size distribution. The operating principle of the Dekati PM10 impactor is based on inertial size classification and gravimetric or chemical analysis of the collected, size classified particle samples. This impactor has cutpoints of 10, 2.5 and 1 μm making it an ideal choice for PM10, PM2.5 and ...
-
Manufactured by Comde-Derenda GmbHbased in GERMANY
Sampling inlets for SPM samplers, sampling systems and real-time monitoring devices. All Comde-Derenda sampling inlets, also known as sampling heads, have been designed and tested specifically for use with our sampling and monitoring systems. They are suitable for measuring various substances, including particulate matter (PM10, PM2.5, PM1 and TSP) and numerous volatile organic compounds ...
-
PremiumManufactured by Apex Instruments, Inc.based in USA
The new XC-53 from Apex Instruments is designed as a cost-effective entry-level metering console for isokinetic sampling. The console features our advanced Peak 32 microcontroller module (MCM) for measuring and displaying stable pressures and temperatures. The transflective LCD screen displays the elapsed time, the pitot velocity pressure (?P), the venturi sample flow pressure (?H) and the ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Temperature controller for operating the heating jacket (PH-2023 or ...
-
PremiumManufactured by Apex Instruments, Inc.based in USA
The Apex Instruments Method 17 Isokinetic Sampling System, featuring the XC-53 metering console, is ideal for collecting and determining in-stack particulate emissions from a wide variety of sources. Particulate emissions are commonly sampled from coal-fired power plants, cement kilns, asphalt plants, incinerators and industrial sources. Emissions data can be used for determining compliance ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you