Only show results available in Virginia? Ok

Portable Analyzers Applications

  • Water quality monitoring systems for portable water plants

    Low maintenance and reliability are key requirements for analyzers in potable water plants. Cost of ownership is another big issue.

    By SWAN Analytische Instrumente AG based in Hinwil, SWITZERLAND.

  • Premium

    Water Analyzing for the Mining Industry

    As a primary industry, the mining industry faces the needs for optimizing the management of its resources. Exploration and excavation activities should be as efficient as possible. Companies also aim to maintain water resources while at the same time controlling the environmental impact of their activities. As pioneers in exotic mining analytics, AppliTek can help you with a selection of application-oriented analyzers, from portable XRF systems to on-line analyzers for water and process applications.

    By AppliTek NV based in Nazareth, BELGIUM.

  • Measurement solution for CFC analyser

    CFCs are used in the manufacture of insecticides and herbicides and the environmental impact of their use must be well controlled. The treatment of CFC emissions to reduce the emissions in the intermediary steps of production needs to be monitored with 100% efficiency. Protea’s portable CFC analysers and continuous CFC monitoring systems can be configured with various sample inlets and analytical modelling to enable multi-samples to be measured on the one system. This means that both inlet and outlet to abatement systems can be monitored using the one analyser.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Monitoring of mercury in ambient air

    Mercury, being widespread in environment, has toxic effect on a human organism even at a low concentration. Therefore, quantitativ e determination of mercury in vari ous environments is one of the most important environmental monitoring problems. The use of a mercury analyzer RA-915M/RA-915+/RA- 915Light with Zeeman background correction provides di rect real-time continuous determination of mercury in air from 0.5 ng/m 3 within the overall possible range of me rcury concentration in ambient air.

    By Lumex Instruments Group based in Mission, BRITISH COLUMBIA (CANADA).

  • Premium

    Gas monitoring instruments and systems for engine emissions measurements

    The exhaust gas from combustion engines is a complex mixture of gases and particulate matter. The composition of the gas may change rapidly. Multicomponent analysis of exhaust gases can be performed with a Gasmet™ FTIR Gas Analyzer with a response time (T90) of one second. The winning combination is the result using of a small volume gas sample cell, a powerful sample pump and a fast detector with liquid nitrogen cooling. The analyzer, sampling system and computer can be assembled on a cart for use in a dynamometer laboratory, or the portable version can be used for roadside tests.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives and regulations set. Two major parts of this on-going quality assurance cycle are the QAL2 and AST procedures. A test laboratory performs tests on the systems on-site, and determines whether the systems fulfill the set requirements or not.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Continuous emissions monitoring in cement kilns

    Various pollutants form in the cement manufacturing process, especially when alternative fuels and waste-derived fuels are used. Typically a cement kiln using these fuels is a required to monitor hydrogen chloride (HCl). Gasmet CEM II is EN 15267-3 approved for HCl measurement in 0 … 15 mg/Nm3 range.High process temperatures result in generation of more nitrogen oxides (NOx) than in typical municipal waste incineration.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Monitoring solutions for the portable multi-gas analyzers

    Portable multi-gas analyzers.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Machine condition monitoring for biofuels

    Overview

    The use of ethanol as a gasoline additive has increased dramatically over the past few years and will likely continue to increase. For fuel blenders, this means an added challenge to avoid an incorrect blend that could lead to regulatory fines, loss of customer confidence and damage to equipment. A quick on-site analysis with a portable mid-infrared based analyzer, such as the InfraCal 2 Ethanol Blend Analyzer shown in the photo, can help fuel blenders quickly flag out-of-spec product and ensure the final blend meets specifications.

    By Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA).

  • XRF analysis for scrap metal recycling

    End suppliers of scrap metal recycling has become more complex and challenging over the years, as customers have become more demanding and metal markets more volatile. The modern scrap metal merchant recycler must be able to make decisions quickly and adapt to changing market conditions in order to remain profitable.

    By Niton UK Limited based in Woodmancott, Winchester, UNITED KINGDOM.

  • Premium

    Gas monitoring instruments and systems for HAZMAT

    Accidents involving chemicals and other hazardous materials require fast and accurate gas measurements as part of the first response. The Gasmet™ DX4040 portable FTIR Gas Analyzer provides reliable identification and concentration measurements of hazardous gases in 60 seconds or less.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    On-site analysis of scrap metal for sorting in the metal recyling industry

    Scrap metal sorting requires fast, accurate, on-site analysis. To achieve maximum price for the scrap, analysis for both incoming and outgoing scrap is required. X-ray Fluorescence (XRF) analysis is widely used within the scrap metal sorting and recycling industry to achieve highest efficiency, most consistent product and best price and all this through Non-Destructive Testing.

    By Oxford Instruments plc based in Abingdon, UNITED KINGDOM.

  • Variable frequency drive controls AC motors

    Consider integrating a variable frequency drive. It often can optimize energy efficiency by enabling you to match motor speed to the demands of the system. Look for opportunities, for example, to replace throttle valves or dampers used to restrict flow. However, a variable frequency drive may not make sense if the load on the motor is relatively small and constant — because speed changes will occur infrequently and any benefits from varying the speed will be negligible. So, thoroughly assess the system load profile to determine the scale and frequency of required speed changes before deciding about installing a variable frequency drive.

    By Variable Frequency Drives based in NSW, AUSTRALIA.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you