Browse all Channels
  1. Companies
  2. ASTM International
  3. News
  4. ASTM A1039 / A1039M - 11 Standard Specification for Steel, ...

ASTM A1039 / A1039M - 11 Standard Specification for Steel, Sheet, Hot Rolled, Carbon, Commercial, Structural, and High-Strength Low-Alloy, Produced by Twin-Roll Casting Process

0

Source: ASTM International

1. Scope

1.1 This specification covers commercial and structural steel sheet in coils and cut lengths produced by the twin-roll casting process.

1.2 The steel sheet is available in the designations listed in Section 4.

1.3 The material is available in the following sizes
Thickness0.027 in. [0.7 mm] to 0.078 in. [2.0 mm]
Widthup to 79 in. [2000 mm]

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Note 1—A description of the Twin-Roll Casting Process is included in Appendix X1.

2. Referenced Documents (purchase separately)

ASTM Standards
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

Index Terms

as-cast sheet; carbon steel sheet; commercial steel; high-strength low-alloy steel; hot rolled steel sheet; steel sheet; structural steel; Carbon steel sheet--specifications; High-strength low-alloy (HSLA) steel; Hot-rolled carbon steel; Steel sheet; Twin-roll casting;

ICS Code

ICS Number Code 77.140.01 (Iron and steel products in general)

DOI: 10.1520/A1039_A1039M-11

ASTM International is a member of CrossRef.

Related news

  • EPA proposes rule to amend CERCLA standards and practices for all appropriate inquiries

    Effective March 14, 2018, the U.S. Environmental Protection Agency is implementing a final rule to amend the CERCLA Standards and Practices for All Appropriate Inquiries of contaminated sites. The rule recognizes the two ASTM standards (ASTM E1527-13 [previous] and ASTM E2247-16 [new]) as consistent with the All Appropriate Inquiries Rule for prospective purchasers of relatively large tracts of rural property or forestlands, including such purchases under a brownfields grant. The rule applies to prospective...

  • New ASTM Standard Supports Direct Kinematic Viscosity Measurement Method Used In Spectro Scientific’s MiniVisc 3000 Series Viscometers

    A new ASTM Standard Test Method supports the simple, convenient, and accurate viscosity measurement method employed in portable MiniVisc 3000 Series viscometers from Spectro Scientific. Spectro is one of the world’s largest suppliers of oil, fuel, and processed water analysis instrumentation and software.ASTM D8092 “Standard Test Method for Field Determination of Kinematic Viscosity Using a Microchannel Viscometer” applies to the Spectro Scienitific MiniVisc 3000 (formerly SpectroVisc Q3000)...

  • News of the ASTM International Board of Directors

    Board Actions Finance and Audit The board approved all proposed ASTM budgets as well as the appointment of Taco van der Maten to serve as chairman of the 2016 Finance and Audit Committee. Van der Maten is marketing manager at PANalytical in Almelo, the Netherlands. He is chairman of Committee F40 on Declarable Substances in Materials and a member of Committees D02 on Petroleum Products, Liquid Fuels and Lubricants and D20 on Plastics. Van der Maten has served on our board since 2013. Mission Statement The...

  • New ASTM International standard Biodegradability of Plastics in the Sea

    Laboratories will soon be able to use a new ASTM International standard to test and better understand biodegradability of plastics in marine environments. The new standard (soon to be published as D7991, Test Method for Determining Aerobic Biodegradation of Plastics Buried in Sandy Marine Sediment Under Controlled Laboratory Conditions) provides ways to simulate how plastics degrade in seawater-soaked sand. According to ASTM member Francesco Degli Innocenti, the recent discovery of major contamination in the...

  • Standards Compliance and Value-Based Product Development

    In the world of construction materials, ASTM International standards are as much a part of doing business as chemical admixtures are a part of concrete. It takes a combination of sound scientific protocol and industry-leading chemical technologies to develop and implement chemical admixtures and cement additives for the construction industry. Whether concrete or hydraulic cement, ASTM standard specifications and test methods are always at the forefront of the process, from the evaluation of raw materials to the...

Customer comments

No comments were found for ASTM A1039 / A1039M - 11 Standard Specification for Steel, Sheet, Hot Rolled, Carbon, Commercial, Structural, and High-Strength Low-Alloy, Produced by Twin-Roll Casting Process. Be the first to comment!