ASTM A350 / A350M - 11 standard specification for carbon and low-alloy steel forgings, requiring notch toughness testing for piping components

0

Source: ASTM International

This specification covers several grades of carbon and low alloy steel forged or ring-rolled flanges, forged fittings and valves for low-temperature service. The steel specimens shall be melt processed using open-hearth, basic oxygen, electric furnace or vacuum-induction melting. A sufficient discard shall be made to secure freedom from injurious piping and undue segregation. The materials shall be forged and shall undergo heat treatment such as normalizing, tempering, quenching and precipitation heat treatment. Heat analysis and product analysis shall be performed wherein the steel materials shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, copper, columbium, vanadium, and nitrogen. The materials shall also undergo tension tests and shall conform to the required values of tensile strength, yield strength and elongation. Impact tests shall also be performed and the steel materials shall conform to the required values of minimum impact energy, temperature, and minimum equivalent absorbed energy. Hardness and hydrostatic tests shall also be performed.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers several grades of carbon and low-alloy steel forged or ring-rolled flanges, forged fittings and valves intended primarily for low-temperature service and requiring notch toughness testing. They are made to specified dimensions, or to dimensional standards, such as the ASME and API Specifications referenced in Section 2. Although this specification covers some piping components machined from rolled bar and seamless tubular materials (see 5.3.3), it does not cover raw material produced in these product forms.

1.2 No limitation on size is intended beyond the ability of the manufacturer to obtain the specified requirements. However, Class 3 of Grade LF787 is only available in the quenched-and-precipitation heat treated condition.

1.3 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified by the purchaser in the order.

1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.

1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact quivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

2. Referenced Documents (purchase separately)

ASTM Standards
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A788/A788M Specification for Steel Forgings, General Requirements
A961/A961M Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications

ASME Standards
B16.47 Large Diameter Steel Flanges

ASME Boiler and Pressure Vessel Code
SectionIX Welding Qualifications

AWS Standards
A5.5 Low-Alloy Steel Covered Arc-Welding Electrodes

API Standards
605 Large Diameter Carbon Steel Flanges

Index Terms

carbon equivalent; pipe fittings, steel; piping applications; pressure containing parts; steel flanges; steel forgings, alloy; steel forgings, carbon; steel valves; temperature service applications, low; Alloy steel forgings--specifications; Alloy steel pipe--specifications; Carbon steel forgings--specifications; Carbon steel pipe--specifications; Low-temperature service applications--steel; Notch toughness; Steel fittings--specifications; Steel flanges--specifications; Steel valves--specifications;

ICS Code

ICS Number Code 23.040.40 (Metal fittings)

DOI: 10.1520/A0350_A0350M-11

ASTM International is a member of CrossRef.

ASTM A350 / A350M - 11 standard specification for carbon and low-alloy steel forgings, requiring notch toughness testing for piping components

Customer comments

No comments were found for ASTM A350 / A350M - 11 standard specification for carbon and low-alloy steel forgings, requiring notch toughness testing for piping components. Be the first to comment!