ASTM B159 / B159M - 11 standard specification for phosphor bronze wire

0

Source: ASTM International

This specification establishes the requirements for round, square, and flat phosphor bronze wires of UNS Alloy Nos. C51000, C52100, and C52400 for general and spring applications. The material for manufacture shall be a casting billet of such purity and soundness as to be suitable for processing by hot working, cold working, and annealing to produce a uniform wrought structure in the finished product. Tempers available under this specification are O61 (annealed), H01 (¼ hard), H02 (½ hard), H03 (¾ hard), H04 (hard), H06 (extra hard), H08 (spring), and H10 (extra spring). Products shall be tested and shall adhere to dimensional (mass, diameter, thickness, length, width, straightness, and edge contours), mechanical (tensile and bending strength, and elongation), and chemical composition requirements.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification establishes the requirements for round, square and flat phosphor bronze wire of UNS Alloy Nos. C51000, C52100, and C52400 for general and spring applications.

1.1.1 Rectangular and square wire of the three alloys are generally available in sizes up to a maximum of 0.188 in. [5 mm] thick and 1.250 in. [32 mm] wide.

1.1.2 Round wire from Copper Alloy UNS No. C51000 is generally available in sizes up to 0.500 in. [13 mm] in diameter.

1.2 The values stated in either inch-pound units or in SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.3 Additional requirements for these products are established in Specification B 250/B 250M, see Section .

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1

It is to be understood that this specification is general. Since the product is used for many applications where the requirements of the operations used are too particular to be specified by any of the ordinary mechanical tests, it is frequently advisable to submit samples or drawings to the manufacturer and secure an adjustment of temper to suit the actual application for which the product is intended.
Note 2

Product in rod, bar and shape form is produced to Specification B 139/B 139M.

2. Referenced Documents (purchase separately)

ASTM Standards
B139/B139M Specification for Phosphorus Bronze Rod, Bar, and Shapes
B250/B250M Specification for General Requirements for Wrought Copper-Alloy Wire
B601 Classification for Temper Designations for Copper and Copper Alloys--Wrought and Cast
B846 Terminology for Copper and Copper Alloys
E8 Test Methods for Tension Testing of Metallic Materials
E8M Test Methods for Tension Testing of Metallic Materials [Metric]
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E290 Test Method for Bend Testing of Material for Ductility
E478 Test Methods for Chemical Analysis of Copper Alloys

Index Terms

phosphor bronze alloy wire; UNS No. C51000 wire; UNS No. C52100 wire; UNS No. C52400 wire;

ICS Code

ICS Number Code 77.150.30 (Copper products)

DOI: 10.1520/B0159_B0159M-11

ASTM International is a member of CrossRef.

Customer comments

No comments were found for ASTM B159 / B159M - 11 standard specification for phosphor bronze wire. Be the first to comment!