ASTM International

ASTM B618 / B618M - 11a Standard Specification for Aluminum-Alloy Investment Castings


Source: ASTM International

This specification covers aluminum-alloy investment castings. Unless otherwise specified, only aluminum alloy conforming to the requirements shall be used in the remelting furnace from which molten metal is taken for pouring directly into castings. The castings shall conform to the chemical composition requirements specified. The determination of chemical composition shall be made in accordance with suitable chemical (test methods E 34), or spectrochemical (test methods E 607 and E 1251) methods. Unless otherwise specified, only aluminum alloy conforming to the requirements shall be used in the remelting furnace from which molten metal is taken for pouring directly into castings. Foundry control shall consist of examination of castings by radiographic or other approved methods for determining internal discontinuities until the gating, pouring, and other foundry practices have been established to produce castings meeting the required quality standards. The tensile properties shall be determined in accordance with test methods B 557 and B 557M. Heat treatment of castings shall be performed in accordance with practice B 917/B 917M.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers aluminum-alloy investment castings designated as shown in Table 1.

1.2 This specification is for aluminum-alloy investment castings used in general purpose applications. It may not address the mechanical properties integrity testing and verification required for highly loaded or safety critical applications.

1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1 (M). The equivalent Unified Numbering System alloy designations are in accordance with Practice E527.

1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.

1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.

1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately)

ASTM Standards
B179 Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes
B275 Practice for Codification of Certain Nonferrous Metals and Alloys, Cast and Wrought
B557 Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
B557M Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)
B660 Practices for Packaging/Packing of Aluminum and Magnesium Products
B881 Terminology Relating to Aluminum- and Magnesium-Alloy Products
B917/B917M Practice for Heat Treatment of Aluminum-Alloy Castings from All Processes
D3951 Practice for Commercial Packaging
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E94 Guide for Radiographic Examination
E155 Reference Radiographs for Inspection of Aluminum and Magnesium Castings
E165 Practice for Liquid Penetrant Examination for General Industry
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E607 Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere
E716 Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spectrochemical Analysis
E1251 Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry

ANSI Standard
H35.1/H35.1(M)-2006 American National Standard Alloy and Temper Designation Systems for Aluminum

Military Standards
MIL-STD-276 Impregnation of Porous Nonferrous Metal Castings

Federal Standard
Fed.Std.No.123 Marking for Shipment (Civil Agencies)

AMS Standard
AMS2771 Heat Treatment of Aluminum Alloy Castings

NAVSEA Standard
S9074-AR-GIB-010/278 Requirements for Fabrication Welding and Inspection, and Casting Inspection and Repair for Machinery, Piping, and Pressure Vessels

Other Standards
CENEN14242 Aluminum and Aluminum Alloys, Chemical Analysis, Inductively Coupled Plasma Optical Emission Spectral Analysis

Index Terms

aluminum; investment casting ; UNS A02040 (Aluminum foundry alloy, casting); UNS A02080 (Aluminum foundry alloy, casting); UNS A02220 (Aluminum foundry alloy, casting); UNS A02420 (Aluminum foundry alloy, casting); UNS A02950 (Aluminum foundry alloy, casting); UNS A03190 (Aluminum foundry alloy, casting); UNS A03280 (Aluminum foundry alloy, castings); UNS A03550 (Aluminum foundry alloy, casting); UNS A03560 (Aluminum foundry alloy, casting); UNS A04430 (Aluminum foundry alloy, casting); UNS A05140 (Aluminum foundry alloy, casting); UNS A05200 (Aluminum foundry alloy, casting); UNS A05350 (Aluminum foundry alloy, casting); UNS A07050 (Aluminum foundry alloy, casting); UNS A07070 (Aluminum foundry alloy, casting); UNS A07130 (Aluminum foundry alloy, casting); UNS A07710 (Aluminum foundry alloy, casting); UNS A08500 (Aluminum foundry alloy, casting); UNS A13560 (Aluminum foundry alloy, casting); UNS A14430 (Aluminum foundry alloy, casting); UNS A17120 (Aluminum foundry alloy, casting); UNS A18500 (Aluminum foundry alloy, casting); UNS A24430 (Aluminum foundry alloy, casting); UNS A25140 (Aluminum foundry alloy, casting); UNS A28500 (Aluminum foundry alloy, casting); UNS A33550 (Aluminum foundry alloy, casting); UNS A47120 (Aluminum foundry alloy, casting); Aluminum alloys (castings)--specifications; Investment castings--specifications; UNS A02010 (Aluminum foundry alloy, casting)

ICS Code

ICS Number Code 77.150.10 (Aluminium products)

DOI: 10.1520/B0618_B0618M-11A

ASTM International is a member of CrossRef.

Customer comments

No comments were found for ASTM B618 / B618M - 11a Standard Specification for Aluminum-Alloy Investment Castings. Be the first to comment!