ASTM International

ASTM D3171 - 11 standard test methods for constituent content of composite materials


Source: ASTM International

A constituent content of a composite material must be known in order to analytically model the material properties (mechanical, physical, thermal, or electrical) of the composite which are affected by the reinforcement or matrix. Also, knowledge of the constituent content is required for evaluation of the quality of a fabricated material and the processes used during fabrication.

The void volume of a composite material may significantly affect some of its mechanical properties. Higher void volumes usually mean lower fatigue resistance, greater susceptibility to moisture penetration and weathering, and increased variation or scatter in strength properties. Knowledge of the void volume of a composite material is desirable as an indication of the quality of a composite.

Reinforcement content may be used to normalize mechanical properties affected by amount of reinforcement in the coupon.

1. Scope

1.1 These test methods determine the constituent content of composite materials by one of two approaches. Test Method I physically removes the matrix by digestion or ignition by one of seven procedures, leaving the reinforcement essentially unaffected and thus allowing calculation of reinforcement or matrix content (by weight or volume) as well as percent void volume. Test Method II, applicable only to laminate materials of known fiber areal weight, calculates reinforcement or matrix content (by weight or volume), and the cured ply thickness, based on the measured thickness of the laminate. Test Method II is not applicable to the measurement of void volume.

1.1.1 These test methods are primarily intended for two-part composite material systems. However, special provisions can be made to extend these test methods to filled material systems with more than two constituents, though not all test results can be determined in every case.

1.1.2 The procedures contained within have been designed to be particularly effective for certain classes of polymer or metal matrices. The suggested applications are discussed in Section 4, as well as at the start of each procedure.

1.1.3 Test Method I assumes that the reinforcement is essentially unaffected by the digestion or ignition medium. A procedure for correction of the results for minor changes in the reinforcement is included. Procedures A through F are based on chemical removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace.

1.1.4 Test Method II assumes that the fiber areal weight of the reinforcement material form is known or controlled to an acceptable tolerance. The presence of voids is not measured. Eq 9 and 10 assume zero void content to perform the calculation.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 9 for additional information.

2. Referenced Documents (purchase separately)

ASTM Standards
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D883 Terminology Relating to Plastics
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D3878 Terminology for Composite Materials
D5229/D5229M Test Method for Moisture Absorption Properties and Equilibrium Conditioning of Polymer Matrix Composite Materials
E12 Terminology Relating to Density and Specific Gravity of Solids, Liquids, and Gases
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E1309 Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases

Index Terms

composite materials ; fiber content; matrix content; reinforcement content; resin content; void volume: Composites--aerospace materials/applications; Fiber content; High modulus fibrous composites--resin-matrix; Matrix digestion; Resins (composite); Void volume;

ICS Code

ICS Number Code 83.140.20 (Laminated sheets)

DOI: 10.1520/D3171-11

ASTM International is a member of CrossRef.

Customer comments

No comments were found for ASTM D3171 - 11 standard test methods for constituent content of composite materials. Be the first to comment!