ASTM F1370 - 92(2011) standard specification for pressure-reducing valves for water systems, shipboard

0

Source: ASTM International

This specification establishes the construction, coding, and performance requirements for self-contained, globe style, pressure-reducing valves used in water systems of shipboard installations that are limited to discharge pressure settings of 200 psig (1379 kPa) and below. The valves shall be either the pressurized spring chamber type (Type I) or unpressurized spring chamber type (Type II). They shall be tested for their conformance with hydrostatic proof, seat tightness, set pressure limits, and capacity.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers self-contained, globe style, pressure-reducing valves for use in water systems of shipboard installations. These valves are limited to discharge pressure settings of 200 psig (1379 kPa) and below.

1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.3 The following precautionary caveat pertains only to the tests portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately)

ASTM Standards
A125 Specification for Steel Springs, Helical, Heat Treated
A193/A193M Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service
A194/A194M Specification for Carbon and Alloy Steel Nuts for Bolts for High-Pressure or High-Temperature Service, or Both
A231/A231M Specification for Chromium-Vanadium Alloy Steel Spring Wire
A276 Specification for Stainless Steel Bars and Shapes
A313/A313M Specification for Stainless Steel Spring Wire
A689 Specification for Carbon and Alloy Steel Bars for Springs
B21/B21M Specification for Naval Brass, Rod, Bar, and Shapes
B26/B26M Specification for Aluminum-Alloy Sand Castings
B61 Specification for Steam or Valve Bronze Castings
B62 Specification for Composition Bronze or Ounce Metal Castings
B148 Specification for Aluminum-Bronze Sand Castings
B150/B150M Specification for Aluminum Bronze Rod, Bar, and Shapes
B637 Specification for Precipitation Hardening Nickel Alloy Bars, Forgings, and Forging Stock for High-Temperature Service
B689 Specification for Electroplated Engineering Nickel Coatings
F467 Specification for Nonferrous Nuts for General Use
F468 Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
F593 Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
F594 Specification for Stainless Steel Nuts

ANSI Standards
ANSIB1.12 Class 5 Interference, Fit Thread

ISA Standards
S75.02 Control Valve Capacity Test Procedure

Federal Specifications
TT-P-645 Primer Paint, Zinc Chromate, Alkyd Type

Military Standards and Specifications
MIL-STD-798 Non-destructive Testing, Welding, Quality Control, Material Control and Identification, and Hi-shock Test Requirements for Piping System Components for Naval Shipboard Use

Other Publications
NavalSeaSystemsComma

Drawings
803-1385947 Flanges, Bronze, 700 PSI WOG for UT Inspection

Index Terms

Globe-style valves; Marine systems/subsystems/equipment--specifications; Pressure-reducing valves; Shipbuilding piping materials--specifications; Shipbuilding steel pipe materials--specifications; Valves--marine vessels;

ICS Code

ICS Number Code 23.060.40 (Pressure regulators); 47.020.30 (Piping systems)

DOI: 10.1520/F1370-92R11

ASTM International is a member of CrossRef.

Customer comments

No comments were found for ASTM F1370 - 92(2011) standard specification for pressure-reducing valves for water systems, shipboard. Be the first to comment!