polyethylene pipe News
-
ASTM F667 - 12 Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings
This specification covers requirements and test methods for materials, workmanship, dimensions, perforations, pipe stiffness, elongation, joint separation resistance, quality of extruded polyethylene, brittleness, bond, and marking of corrugated polyethylene (PE) pipe and fittings. This specification covers tubularly extruded, spirally ...
-
ASTM F2620 - 11e1 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
The procedures described in Sections 7-9 are primarily intended for (but not limited to) field joining of polyethylene (PE) pipe and fittings, using suitable equipment and appropriate environmental control procedures. When properly implemented, strong pressure/leak-tight joints are produced. ...
-
ASTM F2896 - 11 standard specification for reinforced polyethylene composite pipe for the transport of oil and gas and hazardous liquids
1. Scope 1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, and markings for on-site manufactured multilayer reinforced polyethylene composite pipe. It covers nominal sizes 6 in. through 36 in. (150 mm through 915 mm). These multilayered reinforced polyethylene composite pipe ...
-
ASTM F2620 - 11 standard practice for heat fusion joining of polyethylene pipe and fittings
The procedures described in Sections 7-9 are primarily intended for (but not limited to) field joining of polyethylene (PE) pipe and fittings, using suitable equipment and appropriate environmental control procedures. When properly implemented, strong pressure/leak-tight joints are produced. When these joints are destructively ...
-
It Floats! It Sinks!
New Jersey American stretched a one thousand foot, 42 inch diameter, high density polyethylene pipe across it’s Swimming River Reservoir on Thursday. Fitted with concrete collars every several feet, the main was filled with water, sinking it to the reservoir bottom. The new main will provide raw water from a pump station directly to the company’s Swimming River Water Treatment Plant. ...
-
ASTM D2513 - 11c standard specification for Polyethylene (PE) gas pressure pipe, tubing, and fittings
This specification covers the requirements and test methods for material, dimensions, hydrostatic burst strength, tensile strength, chemical resistance, sustained pressure, heat fusion, and impact resistance of plastic pipes, tubing, and fittings used for direct burial and reliner applications in fuel gas mains and ...
-
ASTM F1281 - 11 standard specification for crosslinked polyethylene/aluminum/crosslinked polyethylene (PEX-AL-PEX) pressure pipe
This specification covers a coextruded cross linked polyethylene composite pressure pipe with welded aluminum tube reinforcement between the inner and outer layers. The inner and outer cross linked polyethylene layers are bonded to the aluminum tube by a melt adhesive. Included is a system of nomenclature for the cross linked polyethylene-aluminum cross linked polyethylene (PEX-AL-PEX) pipes, the ...
-
Irritec at Project Qatar 2017 Exhibition
For the first time, Irritec will attend to the next Project Qatar 2017 Exhibition, that will take place from May 8th to 11th 2017, at Doha Exhibition and Convention Center (DECC). The event, one of the world most important for building, environmental technology & materials, will host market’s biggest players from over 30 countries in 32000 mq of exhibition space. During the ...
By IRRITEC SpA
-
ASTM D2239 - 12 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
This specification covers polyethylene (PE) pipe made in standard thermoplastic pipe dimension ratios and pressure rated for water. Polyethylene plastics used to make pipe meeting the requirements of this specification are categorized in two criteria: short-term strength tests and long-term strength tests. The plastics are defined by four hydrostatic design stresses ...
-
ASTM F1563 - 01(2011) standard specification for tools to squeeze-off polyethylene (pe) gas pipe or tubing
This specification covers the physical requirements for tools used to squeeze-off polyethylene gas pipe and tubing. The squeeze bars shall be of a size and configuration that compresses the pipe walls to reduce the gas flow, but does not damage the pipe and ...
-
ASTM F2737 - 11 standard specification for corrugated high density polyethylene (HDPE) water quality units
1. Scope 1.1 This specification covers materials, structural design, physical dimensions and manufacturing requirements for monolithic or sectional corrugated high density polyethylene (HDPE) water quality units with volumes greater than or equal to 140 ft3 or 1,050 gal (4,000 L). 1.2 The corrugated HDPE water quality units ...
-
Aquatech Dewatering to Open Branches in Timmins and Thunder Bay
Aquatech Dewatering, one of Canada’s largest providers of specialized dewatering and pumping solutions, will be opening two new full-service branches in Timmins and Thunder Bay in spring of 2013. “We are pleased to expand our presence in Northern Ontario,” said Andy Ingriselli, President. “The new branches will complement our existing Sudbury branch and provide additional ...
-
JM Eagle Centers New Campaign on Water Conservation and Education
JM Eagle, the world's largest manufacturer of plastic pipe, is joining the effort to call attention to the limited availability of fresh drinking water and education around the world with a three week social media campaign starting March 4 and concluding March 22 on World Water Day. To build awareness for World Water Day, the company will feature posts on its facebook page highlighting the ...
By JM Eagle
-
ASTM F2263 - 07(2011) Standard Test Method for Evaluating the Oxidative Resistance of Polyethylene (PE) Pipe to Chlorinated Water
1. Scope 1.1 This test method describes the general requirements for evaluating the long-term, chlorinated water, oxidative resistance of polyethylene (PE), used in cold water supply or service systems by exposure to chlorinated water. This test method outlines the requirements of a pressurized ...
-
ASTM D2737 - 12e1 Standard Specification for Polyethylene (PE) Plastic Tubing
This specification covers polyethylene (PE) tubing pressure-rated for water. Included here are criteria for classifying PE plastic tubing materials and PE plastic tubing, and requirements and test methods for materials, workmanship, dimensions, bond strength, carbon black, density,.sustained pressure, hydrostatic burst pressure, and environmental stress cracking. ...
-
Aquatech Mexico, a strategic event featuring the latest trends, innovations and solutions for the mexican water industry
The 4th edition of Aquatech Mexico, the international B2B and B2G event for the water industry, will be held from 3 - 5 September 2019 at the World Trade Centre in Mexico City. Cooperation with the National Association of Water and Sanitation Utilities of Mexico (ANEAS) will strengthen what this international platform has to offer. The 2nd edition of the Aquatech Latam Awards for new ...
-
ASTM D2737 - 12 Standard Specification for Polyethylene (PE) Plastic Tubing
This specification covers polyethylene (PE) tubing pressure-rated for water. Included here are criteria for classifying PE plastic tubing materials and PE plastic tubing, and requirements and test methods for materials, workmanship, dimensions, bond strength, carbon black, density,.sustained pressure, hydrostatic burst pressure, and environmental ...
-
ASTM F2805 - 11 standard specification for multilayer thermoplastic and flexible steel pipe and connections
1. Scope 1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, markings for factory manufactured multilayer flexible steel pipe with thermoplastic inner and outer layers and end connections (Fig. 1). It covers nominal sizes 2 in. through 8 in. (50 mm through 200 mm). Flexible steel pipes are multilayered pipe products manufactured in ...
-
ASTM F876 - 10e1 standard specification for crosslinked polyethylene (PEX) tubing
This specification covers crosslinked polyethylene (PEX) tubing that is outside diameter controlled, made in standard thermoplastic tubing dimension ratios, and pressure rated for water at three temperatures. This specification covers one PEX tubing material in one standard dimension ratio and having pressure ratings for water of three temperatures. The pressure ratings decrease as the ...
-
JM Eagle CEO`s Dream of Delivering Clean Water to Rural African Villages Nears Realization
Walter Wang, president and CEO of JM Eagle, recently concluded a tour of water infrastructure in Rwanda, Uganda and Kenya being constructed with hundreds of miles of plastic water pipe his company donated as part of his ongoing efforts to aid impoverished villages in Africa. Shipping from its plants in late 2009, the donation includes nearly 400 miles of a variety of 2.5- to 6-inch pipes, worth ...
By JM Eagle
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you