Guided Wave, Inc.

Axial Process Flow Cell

From

0

Efficient Long Path Flow Cell for Process UV / VIS / NIR Photometry Flow cell performance strongly affects the overall system performance of a process photometer.

High optical efficiency and low sensitivity to environmental factors are essential to sensitive, reliable measurements. Best system performance requires a flow cell that is insensitive to vibration, temperature and pressure changes. Stable performance is especially difficult to achieve when a long-path flow cell is dictated by low limits of detection. Guided Wave’s Axial Flow Cell gives path-lengths of 30mm to 100 mm with exceptional immunity to environment.

  • High optical throughput for low noise spectroscopy
  • Suitable for liquid, gas and vapor streams
  • Cleanout ports at each window make cell maintenance easy
  • Collimated beam for consistently accurate measurements
  • Reproducible pathlength permits servicing in the field
  • 9 mm diameter optics minimize divergence losses
  • O-ring sealed optics to prevent ambient moisture infiltration

The standard Axial Flow Cell is constructed from 316L stainless steel. It can also be made from other materials depending upon specific application requirements, such as Hastelloy C-276. Elastomeric seals prevent leakage and protect the Axial Flow Cell’s vital internal optics. The process and processing environment dictate the actual o-ring material that is best suited for the application. Suitable o-ring materials must be specified to meet your process chemistry and safety requirements. Common materials, such as Viton, Kalrez, EPDM, etc., are readily available.

High optical throughput and exception stability make the Axial Flow Cell particularly effective in achieving low levels of detection. For example, water levels less than 100 ppm can be routinely measured in organics when the Axial Flow Cell is used with a good quality photometer or spectrophotometer. Similarly, the lowest APHA color values are easily measured and onset of yellowness is easily detected.

Like other Guided Wave optical probes, the Axial Flow Cell provides exceptional optical performance. Typically, the longer the pathlength the lower the transmission. Where the Axial Flow Cell is concerned, its peak transmission exceeds 30% which is considerably higher than the competition. That means more signal, lower measurement noise and lower limits of detection!

  • High optical throughput for low noise spectroscopy.
  • Suitable for liquids and vapors.
  • Cleanout ports at each window make cell maintenance a snap.
  • Collimated beam for consistently accurate measurements.
  • Reproducible pathlength permits servicing in the field.
  • Compatible with 200 through 600 micron fiber.
  • Compatible with all fiber optic based UV-VIS-NIR instruments.
  • 9 mm diameter optics minimize divergence losses.
  • O-ring sealed optics to prevent ambient moisture infiltration.

Perhaps the most critical decision in designing a sucessful on-line analyzer system is the selection of the sample interface.

While an insertion probe approach can often reduce installation costs, sometimes safety, servicing, and/or sample conditioning requirements make it necessary to integrate a sampling loop or slip stream. Guided Wave’s Axial Flow Cell is preferred whenever (a) direct insertion probes are inappropriate and (b) the required optical path length is 30 mm or greater.

The Axial Flow Cell is a convenient, compact, rugged sample interface that is easy to install and even easier to service.

  • Pathlength, mm: 30; 50; 75; 100
  • Spectral Range: UV-Vis (200 – 600 nm); Vis-NIR (380 – 2100 nm)
  • Optics: Fused Silica (UV); BK7 (Vis-NIR)
  • Connector Type: SMA 905
  • Process Connection: Nominal 1/4 inch tube connection. Swagelok fittings standard.
  • Optical Efficiency (%T):
    • ≥35% transmission from 800 to 1650 nm for pathlengths ≤50 mm.
    • ≥30% transmission from 800 to 1650 nm for pathlengths >50 mm.
    • ≥25% transmission from 250 to 500 nm for pathlengths ≤50 mm.
    • ≥20% transmission from 250 to 500 nm for pathlengths >50 mm.
  • Temperature range: -20 °C to 170 °C* limited by the o-ring material.
  • Pressure Range: 0 to 500 psig
  • Body Material:
    • SS316L standard;
    • 316SS, Hastelloy C-276, Monel, and Tantalum available on request.
  • Window Material: Sapphire; 6mm thickness
  • Window Seal:
    • Polymer o-ring material options include:
      • Kalrez compounds [#’s 6375, 4079, 2035, LF1050], Viton, EPDM.

Customer reviews

No reviews were found for Axial Process Flow Cell. Be the first to review!