Central Mine - Model CME-45C - Track Carrier Mounted Drills
From Track Carrier Mounted Drills
Truck, trailer, skid, ATV, tracked carrier, helicopter-portable… The CME-45C can be configured to fit your specific drilling applications. Hydraulic feed and retract system provides 19,600 lbs. [8,891 kg] of retract force and 13,650 lbs. [6,192 kg] of down pressure. The 68 inch [173 cm] stroke, hydraulic vertical drive system has no chains or cables which can stretch. It gives you precise control of force on the drilling tools.
-
Most popular related searches
Features
Rugged mechanical rotary drive with up to 4,800 foot pounds [6,507 Nm] of torque.
Several torque and rotation speed combinations are available, including a high-speed rotary drive that gives you up to 700 rpm. The four speed transmission is connected to the drill engine through a heavy-duty clutch. With four forward gears and one reverse, there’s a rotation speed and torque combination available for just about any situation. The mechanical rotary drive also gives you a good feel for changes in soil and drilling conditions down the hole. It allows you to sense the need to adjust feed pressure and rotational torque.
Control logic – the key to operator productivity.
All drilling and set-up controls are logically arranged on a control panel located at the drillers station. A lock-out position for the clutch lever helps prevent accidental engagement. And since the transmission does not travel vertically with the spindle, you won’t find yourself unable to change gears when you’re at the top of the feed stroke.
Patented spindle brake stops rotation in an instant.
Our emergency spindle brake can stop rotation in less than a revolution. This system is activated by two conveniently located push button switches, as well as by strategically located multi-directional wobble switches.
Specification
Engine
- Deutz 197 cubic inch [3.2L] 57 Horsepower [42.5 kilowatt] air-cooled 3 cylinder diesel engine.
Carrier
- Track Width
- 12.6 in [32 cm]
- Avg. ground bearing pressure
- 5.4 psi [.379 kg/cm2]
- Optional Track Width
- 17.7 in [45 cm]
- Avg. ground bearing pressure
- 3.9 psi [.270 kg/cm2]
- Suspension
- Triple walking beams
- Turning Radius
- In place
- Drive
- Hydraulic motor/planetary wheel drives
- Optional 2 Speed drive
- Low Speed: 0-1mph
- High Speed: 0-2mph
- Steering
- Remote radio controlled guidance
- Hydraulic front winch
- 12,000 lbs [5,443 kg]
- Auger and rod racks
- Standard
- Tool boxes
- Standard
Gradeability
- Straight ahead climb
- 46% grade
- Side-hill traverse
- 36% grade
Rotary drive
- Standard
- Rotary Torque
- 3,395 foot pounds [4,603 Nm]
- Rotary Speed
- up to 643 rpm max
- Rotary Torque
- High torque
- Rotary Torque
- 4,815 foot pounds [6,528 Nm]
- Rotary Speed
- up to 453 rpm max
- Rotary Torque
- High speed
- Rotary Torque
- 3,115 foot pounds [4,223 Nm]
- Rotary Speed
- up to 700 rpm max
- Rotary Torque
- Clutch, heavy duty
- 13 inch [33 cm]
- Transmission
- 4 speed forward, 1 speed reverse
Hydraulic feed system
- Retract force
- 19,600 pounds [8,891 kg]
- Pulldown force
- 13,650 pounds [6,192 kg]
- Retract rate (max)
- 55 feet [17 m] per minute
- Feed Rate (max)
- 79 feet [24 m] per minute
- Stroke
- 68 inch [173 cm]
Leveling system
Four hydraulic jacks, inverted design with chrome-plated piston rods enclosed at all times.
- Stroke
- 36 inch [91.4 cm]
Optional Equipment
Hydraulic rod holder and breakout wrench†
The hydraulic rod holder makes your job quicker and safer. It not only pivots from on-hole to off-hole positions, but also hydraulically moves in and out. For efficient operation, the breakout wrench is mounted at the pivot point of the rod holder arm.
Automatic SPT hammer †
Our 140 pound [63.5 kg] automatic hammer gives you extremely consistent and accurate Standard Penetration Test results, meeting all ASTM-D-1586 requirements. Thats because there are no ropes or cables to impede the free fall of the weight.
The hammer swings from stored position to on-hole position. Since raising and lowering is done hydraulically, set up is quick and almost effortless.
For maximum safety, all moving parts are enclosed, including the impact area between the weight and the anvil. A 340/140 pound [154/63.5 kg] hammer is also available.
Auger and rod storage
Above deck auger and rod racks are provided with the drill carrier.
Several tool box,water tank, auger and rod storage configurations are available.
Slide bases make the job easier and quicker.
Slide base options are available in both in-out and sideways movement of the drill on the carrier.
A 15 inch [38.1 cm] in-out movement allows you to quickly move the drill on and off the borehole and align the sheaves for lifting tools with the cathead or any of the hoists.
A 8 inch [20.3 cm] sideways movement gives you even more versatility. Aligning augers or rods when making connections is easy. If the bit drifts off at an angle when you start a hole, you can quickly straighten it to a vertical position.
Since the upright and optional mast are mounted directly to the drill frame, they move with the drill when the slide base is used. That means you can drill in any position within a 170 square inch [1097 cm²] area without moving the carrier.
If you have ever tried to line up your rig on an existing bore hole, you’ve probably already recognized another benefit of the slide base.
Angle drilling system for special applications†
This unique system allows you to drill holes at various angles between horizontal and vertical. It is especially effective for drilling under ponds, storage tanks or other structures. When used with our patented Continuous Sample Tube System, you can even take soil sample while drilling angle holes.
The angle drilling system will also allow you to drill vertically with the rig positioned on an uphill slope. That can eliminate the time consuming job of leveling an area on which to place the rig.
Since the kelly drive is directly connected to the right angle drive box, you can raise and lower the mast with the drive train already connected and ready to go.
Additional optional equipment
- Water tank
- Continuous sample tube system
- Stabilized side feed water swivel
- Pavement coring attachment
- Auger and rod guides for angle drilling
- Mast (from base of frame to sheaves)
- 15 foot [4.5 m]
- 18 foot [5.5 m]
- 20 foot [6.1 m]
- Cathead, 8 inch [20.3 cm] diameter
- Hydraulic hoist
- 1,800 pound [816 kg], max line speed 200 ft [61 m] per minute
- 3,200 pound [1,452 kg], max line speed 100 ft [30.5 m] per minute
- 5,000 pound [2,268 kg], max line speed 50 ft [15 m] per minute
- Hydraulic wireline hoist
- 900 pound [408 kg], max line speed 400 ft [122 m] per minute
- 1,800 pound [816 kg], max line speed 200 ft [61 m] per minute
- Water pumps
- Progressing cavity
- 36 gpm/225 psi [136 lpm/1,551 kPa]
- 84 gpm/225 psi [318 lpm/1,551 kPa]
- Triplex piston
- 20 gpm/600 psi [70 lpm/4,137 kPa]
- Other pumps available
- Progressing cavity
Downloads related to this product
Soil Sampling Brochure
Drilling Tools Brochure
Diamond Bits Brochure
Customer reviews
No reviews were found for Central Mine - Model CME-45C - Track Carrier Mounted Drills. Be the first to review!