Aerosol Separation Equipment In Europe
-
Manufactured by Plastoquimica, S.Lbased in SPAIN
Aerosols are solid or liquid suspended particles with diameters in size of 10 to 20 microns (submicron range). PLASTOQUIMICA offers a new multistage ordered packing system for the separation of aerosols, being able to achieve a degree of separation down to 0.2 microns. One of its main advantages is that we provide a custom ...
-
Manufactured by AWS Corporation Srlbased in ITALY
Pocket vane technology consists of closely spaced metal plates that form a zig-zag flow path. Unique to these pocket vanes are internal drain channels in a "hollow vane" design that allow collected liquids be shielded from the gas flow and drain without the opportunity for re-entrainment. Gas flow can be either vertically or ...
-
Manufactured by AWS Corporation Srlbased in ITALY
The liquid droplets, due to their momentum, impact on the wires and are separated from the gas flow as they are unable to follow the gas streamlines. MESHPAD are inertial separators because liquid droplets are removed due to their inertial ...
-
Manufactured by AWS Corporation Srlbased in ITALY
FIBERWIND™ type mist eliminators of AWS are specifically made to remove mainly submicron liquid or soluble solid particles from an air or gas stream. They are similar to mesh pad mist eliminators except that the filaments are extremely fine fibers, randomly but very closely spaced. FIBERWIND™ mist eliminators of AWS are constructed in a cylindrical form (candle filters) between two ...
-
Manufactured by AWS Corporation Srlbased in ITALY
TIDEVANE type mist eliminator types are widely used in industry to separate liquid droplets from gas streams. In all the applications where a contact between liquid and flowing gas is involved, tiny mist droplets are carried away with the gas. TIDEVANE type mist eliminators of AWS are specifically made to remove mainly liquid droplets ...
-
Manufactured by AWS Corporation Srlbased in ITALY
AWS’s liquid-liquid separation technology can solve a wide range of separation problems involving immiscible liquids. Whether it is capacity constraints, loss of valuable solvents or more stringent environmental compliance, AWS Corp can help you meet these ...
-
Manufactured by Plastoquimica, S.Lbased in SPAIN
The operating principle is based on the action of centrifugal and gravitational forces on the particles contained in the gas discharge, so that while these are retained in the device, the gas continues its path outward, free of particles or containing lower concentration of ...
-
Manufactured by Plastoquimica, S.Lbased in SPAIN
This revolutionary filter element, designed and patented by the German company HERDING FILTERTECHNIK GMBH, is a new concept in the design of filtration units and the biggest breakthrough in filtration technology in the last 50 years. Its special configuration provides a filter surface three times that of a conventional filter with high efficiency filtration for even the most difficult products. ...
-
Manufactured by Plastoquimica, S.Lbased in SPAIN
Standard venturi scrubber design consists of a scrubber and a centrifugal separator. This system is so universal that allows different constructions. The collection efficiency of the venturi scrubber is related to the pressure drop of the system. A greater pressure drop in the system, the greater the efficiency. One possibility to ...
-
Manufactured by VSS-Umwelttechnik GmbHbased in GERMANY
%. The elimination rate depends on the size and density of the droplets to be separated and on the viscosity of the carrier gas. An even better separation may be achieved by additional aerosol separators (model T120-2/A, mesh type) which are, for example, required for chromic acid. A rinsing device for the purification of the ...
-
Manufactured by TREMA Verfahrenstechnik GmbHbased in GERMANY
Cost-effective aerosol separation (<1µm), Odour elimination, Alternative to electrostatic precipitators, Minimum maintenance, Suitable for product recovery ...
-
Manufactured by Brechtelbased in USA
The PCVI is a virtual impactor that allows on-line separation of coarse from fine aerosol. The separation size is variable over the 0.3 to 5 micron diameter range, and the device is small enough to fit in the palm of your hand. With two mass flow controllers, the flows inside the PCVI can be varied to quickly change the particle size that ...
-
Manufactured by AirPhoton, LLC.based in USA
The Single Inlet/Filter Unit employs a PM10 inlet designed to run at 5 liters per minute. The flow rate can be adjusted by a manual valve in the Sampling Control Box. An option exists to further separate PM2.5 and coarse mode (2.5 lessthan d lessthan10mm) aerosols using Nuclepore filter separation in our FC10 filter cartridge. Other size ...
-
Manufactured by Tisch Environmental Inc. - Tisch Internationalbased in USA
The dichotomous air sampler is a dual-filter air sampler for thesimultaneous collection of the fine PM2.5 and the coarse PM10-2.5particles contained within PM10. Split flow configuration of the virtualimpactor allows a PM10 aerosol to be separated into fine particles andcoarse particles for subsequent collection onto 2 separate ...
-
Manufactured by Tisch Environmental Inc. - Tisch Internationalbased in USA
The dichotomous air sampler is a dual-filter air sampler for the simultaneous collection of the fine (PM2.5) and the coarse (PM10-2.5) particles contained within PM10. Split flow configuration of the virtual impactor allows a PM10 aerosol to be separated into fine particles and coarse particles for subsequent collection onto 2 separate ...
-
Manufactured by TBH GmbHbased in GERMANY
and particles or aerosols. In order to keep as few system parts as possible from contamintaion, simple and reliable cleaning/ disinfection as well as a convenient filter change are important. The InLine filter is a pre-filter in the capture element. It is located in the extraction hood close to the patient. It captures and filters emerging particles/ ...
-
Manufactured by VSS-Umwelttechnik GmbHbased in GERMANY
VSS-Umwelttechnik offers a new type of Venturi scrubber system Bayer-Reither with hybrid nozzles for the separation of aerosols and fine dusts. These scrubbers (system Bayer-Reither) are marketed under licence with Reither Venturiwäscher ...
-
Manufactured by Colasit AGbased in SWITZERLAND
of their inertia, the droplets collide with the walls of the section, are then separated and can be removed from the system ...
-
Manufactured by Kappa Filter Systems GmbHbased in AUSTRIA
The Kappa Airdry™ filter system is able to handle a wide range of oil and emulsion exhaust air compositions. The filter stages can be individually configured and modified. It is even possible to switch to another cooling ...
-
Manufactured by Kappa Filter Systems GmbHbased in AUSTRIA
The Kappa Sorbdry™ is a high-performance filter for the filtration of combinations of aerosols, gaseous emissions and odours. It can be perfectly adapted to the task at hand – regardless of the composition and intensity of the raw gas load. The adsorbent filter elements enable targeted filtration of gaseous emissions and ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you