Backflow Prevention Valve Equipment Available In Africa
-
Manufactured by Mifab, Inc.based in USA
The BEECO Series Barracuda 20 Double Check Valve Assembly (DC) is designed to prevent non-health hazard pollutants from entering the potable water supply system caused by backpressure and/or backsiphonage conditions. USC ...
-
Manufactured by Climate Tanksbased in USA
Same character as backflow prevention valve DN 100, additional with special overflow siphon uno, overflow with odour trap and suction of the surface ...
-
Manufactured by Climate Tanksbased in USA
3P Backflow Prevention Valve DN 100 prevents the backflow of any contaminated water entering the rainwater tank. It is suitable for installation in tubes DN 100 and exists of a standard backflow security. The backflow prevention valve allows the ...
-
Manufactured by Febco - a Brand of Watts Water Technologies Companybased in USA
Series 611 flange by flange valve setters are constructed of fusion epoxy-coated ductile iron. These valve setters are designed to augment the installation of the N series backflow prevention valves. Integral ductile iron supports between elbows transfer thrust downstream, thus eliminating thrust block ...
-
Manufactured by Aquobexbased in UNITED KINGDOM
Mains sewage backflow prevention valve. Fits into existing manhole. DIY solution. Single flap valve can be manually locked ...
-
Manufactured by Aquobexbased in UNITED KINGDOM
Mains sewage backflow prevention valve. Fits in-line with sewage pipe but new manhole not ...
-
Manufactured by Aquobexbased in UNITED KINGDOM
Mains sewage backflow prevention valve. Dual flaps for added security. Fits in-line with sewage pipe in new manhole. Automatic operation with manual lock if ...
-
Manufactured by Climate Tanksbased in USA
Same character as backflow prevention valve DN 100, additional it has a special overflow with odour trap and suction of the surface water. The 3P Backflow Prevention duo is installed inside the rainwater tank, between the filter and the tank wall overflow outlet. Therefore unnecessary installation time and ...
-
Manufactured by Cash Acmebased in USA
temperature is 180°F (82°C). The V-3 is available chrome-plated (V-3C) on special order. Note: These units are not intended for use where water contamination could occur as a result of draining or for permanent continuous pressure installation. For continuous pressure systems, install the BFP Backflow Preventer ...
-
Manufactured by Mack Valvesbased in AUSTRALIA
Ball float valves use a float to open and close water flow to maintain a set water level in a tank to prevent backflow. Float valves are used in many industrial applications, including cooling towers, condensate tanks, reservoirs and open or closed storage ...
-
Manufactured by GW Sprinkler A/Sbased in DENMARK
This valve is designed to supply water at constant pressure to a wet automatic sprinkler system. It is typically used where zones with automatic sprinkles shall operate at a lower pressure than provided by the fire pump. The C-300 sprinkler valve has a built in non-return facility which prevents backflow if the ...
-
Manufactured by SVR Globalbased in USA
SVR Global is the foremost Swing Valve Manufacturer in USA. When the fluid in the line reserves direction, a swing valve allows flow in one direction while automatically preventing backflow. The clack valve or non-return valve is another name for a swing valve. Swing ...
-
Manufactured by NTGD Valve Co. LTDbased in CHINA
A Swing Check Valve is desinged to prevent the medium in the pipeline from flowing back. As pressure reaches zero, the valve shuts fully to prevent backflow. Swing check valves belong to the group of automatic valves, which are used mostly in pipelines where the medium flows in ...
-
Manufactured by Tideflex Technologies - a Division of Red Valve Company, Inc.based in USA
The Tideflex Series 35 in manufactured similarly to the Series TF-2, with the addition of an integral elastomeric flange. The 35 can be mounted to mating flanges or wall thimbles or directly to concrete walls. The 35 design has been enhanced by the 35-1, flat-bottom, Duckbill Check Valve. The 35-1 requires minimal bottom clearance and the ...
-
Manufactured by Tideflex Technologies - a Division of Red Valve Company, Inc.based in USA
In some applications, a slip-on Tideflex duckbill check valve (TF-1) is not feasible because of an existing mating flange or wall thimble, or a flanged connection is preferred, or it is desired to mount the valve directly to a concrete wall. In these cases, the 35-1 Duckbill Check Valve is the ...
-
Manufactured by Tideflex Technologies - a Division of Red Valve Company, Inc.based in USA
The TF-2 was the first duckbill check valve introduced by Red Valve Company. The TF-2 was developed based on a United States EPA grant in the 1980’s to overcome excessive costs in maintenance and replacement of non-performing flap gates. Hundreds of thousands of Tideflex have been installed since then providing reliable backflow ...
-
Manufactured by Comeval Valve Systemsbased in SPAIN
Wafer swing check valves for water works and HVAC UNIWAT CV. Wafer swing check valves to prevent the reverse of flow in a piping system, by means of its articulated disc. Wafer design for installation between flanges. Light and compact, mainly used in hvac and industrial auxiliary ...
-
Manufactured by Tideflex Technologies - a Division of Red Valve Company, Inc.based in USA
The Tideflex Series 37-G is a special adaptation of the Series 37. The 37-G can be completely inserted into a pipe which effectively gives it a zero face to face dimension. The outside diameter of the 37-G’s cuff is fabricated to precisely match the inside diameter of the pipe, providing a press-fit. The valve is supplied with an ...
-
Manufactured by Tideflex Technologies - a Division of Red Valve Company, Inc.based in USA
The TF-1 has become the preferred Tideflex configuration for outfalls. Designed for in-structure and end-of-pipe installations, the TF-1 features a flat bottom and flared top. This allows the valve to be installed at a lower overall elevation than other configurations, with less bottom clearance required. This is especially important in ...
-
Manufactured by Tideflex Technologies - a Division of Red Valve Company, Inc.based in USA
The Tideflex Series 37-G Thimble Insert is comprised of a Series 37-G Duckbill Check Valve mounted in a thimble. The 37-G is pre-assembled, clamped and pinned into the thimble prior to shipment. The Thimble Insert can be provided flangeless or with a circular or rectangular flange and the 37-G can either face the flange or away from the ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you