Only show results in Virginia? Ok

bilge water monitoring equipment

  • Premium

    TDHI - Model TD-107 - Oil Content Monitor

    The TD-107 Oil Content Monitor is the most reliable way to to measure oil content in a typical ship’s oily waste holding tank, bilge, or oily water separator.

    By Turner Designs Hydrocarbon Instruments, Inc. based in Fresno, CALIFORNIA (USA).

  • JOWA - Condensation Water Monitor

    The JOWA SEAGUARD 15ppm Bilge alarm is designed to monitor the effluent from a bilge water separator. The alarm is approved to IMO MEPC 107(49).

    By JOWA based in Kållered, SWEDEN. from Condensation Water Monitor Product line

  • DECKMA - Bilge Alarm

    DECKMA is a global leader in bilge effluent monitoring. DECKMA was one of the first manufacturers to receive IMO resolution MEPC.107(49) approval for their OMD-2005 Bilge Alarm. Today DECKMA supplies to Bilge Separator manufacturers the newer version OMD-24, and for retrofitting of existing installations the OMD-24 and 2008. All systems are ...

    By Hermont Marine Inc. & Hermont Tech based in St Laurent, QUEBEC (CANADA). from Bilge Alarm Product line

  • Deckma OMD-21 - Oil Water Monitor - 15ppm Bilge Alarm

    The OMD-21 Bilge Alarm Monitor was designed by Deckma Hamburg GmbH for use in conjunction with 15 ppm Oily Water Separator Systems. The performance and specifications of the OMD-21 comply with the International Maritime Organization (IMO) requirements described in Resolution MEPC.60 (33).

    By Mackay Communications, Inc. based in Raleigh, NORTH CAROLINA (USA).

  • EPE POSEIDON - Model EC - Bilge Oil Water Separator

    POSEIDON EC Bilge Oil Water Separator consists of two stages; the coalescer and the electrolytic emulsion breaking unit. The coalescer works on a continuous mode, by-passing the second stage. If the detection monitor senses content higher than 4ppm at the effluent of the coalescer oil, then the emulsion breaking unit begins its ...

  • EPE POSEIDON - Model FIT - Bilge Oil Water Separator

    POSEIDON FIT Bilge Oil Water Separator consists of two stages; the coalescer and the emulsion breaking unit. The coalescer works on a continuous mode, by passing the second stage, and only when the oil detection monitor detects at the effluent of the coalescer oil content higher than 4ppm, then the emulsion breaking unit begins its operation. ...

  • Model 204 - Water Monitor

    Oil in Water Monitor | The ability to analytically quantify oil in water is greatly enhanced with the Sample Transfer Stripper (exclusive ASI Membrane Technologies) and the solid state sensor offered by Analytical Systems Keco. The analyzer is very easy to maintain and does not require routine calibrations in the field. It is field-proven to ...

    By Analytical Systems Keco based in Houston, TEXAS (USA). from Water Monitor Product line

  • JOWA - Model SeaGuard - 15ppm Bilge Alarm

    The JOWA SEAGUARD 15ppm Bilge alarm is designed to monitor the effluent from a bilge water separator. The alarm is approved to IMO MEPC 107(49).

    By JOWA based in Kållered, SWEDEN. from 15ppm Bilge Alarm Product line

  • Model TD-107 - 15 PPM Bilge Oil Content Monitor

    The TD-107 Fluorescence Oil Content Monitor (OCM) is a 15 ppm bilge alarm for oily water separators based on fluorescence detection technology. Fluorescence makes the TD-107 resistant to interferences by turbidity or particles and sediments in the bilge which impact competing 'light scatter' oil content monitors. Because silt, algae, iron oxide ...

    By NAG Marine based in Norfolk, VIRGINIA (USA). from 15 PPM Bilge Oil Content Monitor Product line

  • Model TD-107 5.0 - 5 PPM Bilge Oil Content Monitor

    The TD-107 5.0 is the world's first and only DNV Clean Design Certified 5ppm Bilge Oil Content Monitor. The TD-107 5.0 is an extension of the highly successful TD-107 Oil Content Monitor for oily water separators, except with an added level of testing and certification for 5ppm applications by Det Norske Veritas' Clean Design program.

    By NAG Marine based in Norfolk, VIRGINIA (USA). from 5 PPM Bilge Oil Content Monitor Product line

  • RWO - Bilge Economiser System

    On board every ship, so called ‘clean drains’ are treated in oil-water separation systems and strain machines and resources. These clean drains usually consist of leakage of and condensate from equipment used for seawater, fresh water, steam, air conditioning, etc., which are usually not contaminated by oil.

    By RWO GmbH Marine Water Technology based in Bremen, GERMANY. from Bilge Economiser System Product line

  • Model OMD- 32 Series - Oil-in-Water Monitor

    The OMD-32 Oil-in-Water Monitor has been designed specifically for use in conjunction with oil-water separator units. The OMD-32 has been constructed using technology of the DECKMA HAMBURG OMD series industrial instruments and 15ppm Bilge Alarm Monitors, that have a specification and performance which exceeds the requirements of the International ...

    By Deckma Hamburg GmbH based in Hamburg, GERMANY.

  • BilgeRemed - Pretreatment of Oily Bilge Water on boats & Ships

    BilgeRemed is effective in ship-board bioremediation of oily bilge water on ships both under sail as well as those berthed for long periods at the shore. Pre-treating oily bilge water with BilgeRemed before passing it through oil water separators has been shown to reduce the TPH concentration in the discharge water to less than 15 ppm, as required ...

    By Sarva Bio Remed, LLC based in Emigsville, PENNSYLVANIA (USA).

  • Model 15 ppm - Bilge Alarm Type BilgMon 488TM

    Petrik Naval has engineers to carry out the annual and 5th annual calibration, certification and verification, also troubleshooting and repair of Oily Water  Separator 15ppm Bilge Alarm Monitors. According to the new MEPC 107(49) compliant monitors, and the old MEPC 60(33) compliant monitors. Bilge Alarms for  the marine market, are ...

    By Petrik Naval based in PI Palmones, SPAIN.

  • SmartSafe - Bilge Overboard Security System

    By enabling the cost-effective prevention of illegal discharge to sea, the SmartSafe enables the operator to demonstrate MARPOL Compliance. Easy to install and requiring low maintenance, the system is capable of recording other miscellaneous ships data and generating shore-based event reports. SmartSafe is compatible with all IMO Resolutions MEPC ...

    By Rivertrace Engineering Ltd based in Redhill, UNITED KINGDOM. from Bilge Overboard Security System Product line

  • Oil Content Monitor

    The OCD CM is the result of market research and development of new technologies to produce a monitor that exceeds the existing standards and meets the requirements requested by customers and operators worldwide. The OCD CM has been specifically designed to eliminate the effects that cause false instrument alarms where the water contains high ...

    By SkimOil Inc. based in Carrboro, NORTH CAROLINA (USA). from Oil Content Monitor Product line

  • JOWA - Model 3SEP OWS - Oily Water Separator

    The 3SEP OWS is a dual stage oily bilge water separation system utilizing differential specific gravity, coalescence plates and filtration to separate and remove free and emulsified oil. The unit is available in five different capacities; 0.5 m3/h, 1.0 m3/h, 2.5 m3/h, 5.0 m3/h and 10.0 m3/h. The skid is optimised so that the footprint of the 3SEP ...

    By JOWA based in Kållered, SWEDEN. from Oily Water Separator Product line

  • Model RWO OWS-COM - Oily Water Separator

    More than 20,000 ships have already been equipped with RWO’s oily water separators since 1975. Like previous RWO Oily Water Separators, the OWS-COM uses a combination of a highly effective open porous coalescer with automatic backflushing, together with a second stage emulsion breaking oil and hydrocarbon polisher. The periodical ...

    By NAG Marine based in Norfolk, VIRGINIA (USA). from Oily Water Separator Product line

  • Global Advantech - Model TDS801 - Electrocoagulation and Advanced Electrochemical Oxidation

    Electrocoagulation is an electrochemical process for the treatment of waste water, effluent, process water, produced water, bilge/ballast water, mine tailings, etc. The process was originally developed in 1906 to treat bilge water from ships, but was never adopted at the time due the lack of legislation concerning marine discharges.

  • Mobile Oil-Water Separators and Flotation Systems

    Mobile oil-water separators are mainly used for cleaning stationary oil interceptors or catch basins for oily wastewaters or bilge oils directly on site. In general, the contents of these basins and containers are completely sucked off by a vacuum truck. Instead of sucking off the phases oil, water and sludge together, the single phases can be ...

    By OKO-tech Maschinenbau GmbH & Co.KG based in Hess. Oldendorf, GERMANY.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you