Booster Pump Equipment In Australasia
-
PremiumManufactured by Cornell Pump LLCbased in USA
Cornell's EDGE End Gun Booster pump for Center Irrigation Pivots is a retrofit that enhances pivot systems. With the reliable and renowned Cornell design, these competitively-priced pumps come in 3HP and 5HP models and can be shipped immediately. ...
-
PremiumManufactured by Cornell Pump LLCbased in USA
The 2B Edge End Gun Booster pump is designed with Cornell's renowned quality and durability. It features a 2" discharge, 2.5" suction, and enclosed impeller. Cornell's patented Cycloseal0 design is ...
-
Manufactured by Water Services Inc.based in USA
The WSI-BS-150-58-266-SS Booster Pump Skid is designed to boost pressure of culinary water systems. It is ideal for use in buildings or camps with 150 to 180 people, or any other application where 150GPM and constant pressure is ...
-
Manufactured by Cla-Valbased in USA
Cla-Val 60-11 and 660-11 Booster Pump Control Valves are pilot-operated valves designed for installation on the discharge of booster pumps to eliminate pipeline surges caused by the starting and stopping of the ...
-
Manufactured by Cla-Valbased in USA
Cla-Val 60-73 & 660-73 Booster Pump Control Valves are pilot-operated valves designed for installation on the discharge of booster pumps to eliminate pipeline surges caused by the starting and stopping of the ...
-
Manufactured by RephiLe Bioscience, Ltdbased in USA
This is a booster pump designed to increase feed water pressure. Comparable to Millipore ZF3000000, ZF3OOOOOO replacement PUMP for Millipore Elix 3/5/10, Elix UV 3/5/10 and RiOs 5/8/16 systems ...
-
Manufactured by Smith & Loveless Inc.based in USA
Smith & Loveless designs and manufactures custom-built packaged water booster stations. Completely assembled in a quality-controlled manufacturing environment, S&L Water Booster Stations arrive at the job site fully tested and ready for ...
-
Manufactured by Mueller Water Productsbased in CANADA
The 106-BPC and 206-BPC booster pump control valves are installed in-line, directly downstream of the pump discharge. The pump control valve is normally closed and on pump start-up, a pilot solenoid is energized to open the valve, at a rate governed by the opening speed control. When shut-down is required the ...
-
Manufactured by Mueller Water Productsbased in CANADA
The 106-PG-BPC or 206-PG-BPC booster pump control valve is installed in-line directly downstream of the pump discharge. The valve is normally closed, and, on pump start-up, a pilot solenoid is energized to slowly open the valve, at a rate governed by the opening speed control. The pipeline flow is gradually ...
-
Manufactured by Cla-Valbased in USA
The Cla-Val Model 60-BY Booster Pump Control valve is a pilot-operated valve designed for installation on the discharge of booster pumps to eliminate pipeline surges caused by the starting and stopping of the pump. The CSM11-HC solenoid valve controls the valve ...
-
Manufactured by Cla-Valbased in USA
The Cla-Val Model 60-19/660-19 Pump Control Valve with a High-Capacity Pilot System is a pilot-operated valve designed for installation on the discharge of booster pumps to eliminate pipeline surges caused by the starting and stopping of the pump. Specifically designed for larger sized pump ...
-
Manufactured by Tuthill Corporation - Tuthill Vacuum & Blower Systemsbased in USA
Combine high pumping speed with deep vacuum levels and operate free of oil, water or other sealing liquids. Flows range to 4,500 CFM (7646 m3/h) with vacuum levels to 10 microns and below Complete engineered solutions are available and may include any combination of dry screw vacuum pumps, vacuum boosters, electric motors, direct of V-belt ...
-
Manufactured by Tuthill Corporation - Tuthill Vacuum & Blower Systemsbased in USA
Pump high volumes at very low pressure. High-capacity dry rotary lobe vacuum booster is matched to a smaller rotary piston vacuum pump. For continuous operation below 1 Torr (1.3 mbar a), the vacuum booster can increase pumping speed by a factor of 10 or more. For operation at higher pressure and for faster ...
-
Manufactured by Tuthill Corporation - Tuthill Vacuum & Blower Systemsbased in USA
Ideal for pumping wet gas mixtures at low pressures. Oil-filled systems avoid problems with corrosive contaminants and sealant liquid vapor pressures at higher temperatures. Process liquid-filled systems prevent contamination of process gases with either water or oil. A variety of two and three-stage systems are available, ...
-
Manufactured by Proactive Environmental Products International LLC (PEPI)based in USA
The Engineered Plastic 12-volt submersible centrifugal Cyclone® pump is capable of pumping up to 25 feet from ground level (DTW)* by simply connecting the Cyclone® to a 12-volt deep cycle battery. Its reliable design is perfect for continuous sampling and purging of groundwater wells and Low Flow Sampling (Fractional Flow®). The ...
-
Manufactured by Tuthill Corporation - Tuthill Vacuum & Blower Systemsbased in USA
Simple, robust design can handle process by-products – liquids, condensate, and even small particles. No oil or water in contact with process. No contact between operating components in the casing. Full pumping speed from atmospheric pressure down to 1 Torr; ultimate pressure 0.1 Torr (.05 Torr on Model KDP-800). Quiet operation – ...
-
PremiumManufactured by Royal Eijkelkampbased in NETHERLANDS
This low cost submersible pump set is suitable for use in monitoring wells with a diameter of minimal 40 mm. The set includes three submersible pumps “Gigant”, three booster pumps, a roll of extension cable, sealed crimp splices (to make a waterproof cable extension), a roll of polyethylene sampling tube and a battery ...
-
PremiumManufactured by Apex Instruments, Inc.based in USA
The new XC-53 from Apex Instruments is designed as a cost-effective entry-level metering console for isokinetic sampling. The console features our advanced Peak 32 microcontroller module (MCM) for measuring and displaying stable pressures and temperatures. The transflective LCD screen displays the elapsed time, the pitot velocity pressure (?P), the venturi sample flow pressure (?H) and the ...
-
PremiumManufactured by Tekran Instruments Corporationbased in CANADA
The Tekran Model 3400-WTR Water Filtration System is an inexpensive, convenient source of deionized, mercury free water for the Tekran 3400 Mercury CEM. With two stages of pre-filtration eliminating particulate and organic contamination, the final stage R/O membrane and ion-exchange filters have extremely long life. The Model 1306 can supply enough water for up to four CEM systems. The filter ...
-
PremiumManufactured by Tekran Instruments Corporationbased in CANADA
The Tekrarr Model 1308 Recirculating Water Purification System is an inexpensive, convenient source of deionized, mercury-free water for the Series 3300Xi Mercury CEM. The system has two stages of pre-filtration to eliminate all particulate and organic contamination in the water. A reverse osmosis (R/O) unit then removes the bulk of ionic material. Two stages of finishing ion exchange (IX) resin ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you