Only show results in Virginia? Ok

Cone Penetration Testing equipment

  • Cone Penetration Test

    Seismic test are carried out to measure shear (S wave) and compression wave (P wave) velocities in soils. The SCPT method combines the seismic test with results from the CPTU probe, and will give you a good basis for evaluation of a number of critical soil properties, e.g. the risk for liquefaction.

    By Ingenjörsfirman Geotech AB based in Askim, SWEDEN. from Cone Penetration Test (CPT) Product line

  • Pagani - Model CPT - Cone Penetration Testing Tests

    The CPT test (mechanical type) is essentially the extent of resistance to opening up a bit of size and mechanical characteristics standardized, stuck in a land-speed constant (2 cm / sec). In Cone Penetration Testing, with the Begemann Mechanical Cone, the Qc (tip resistance) and RL (side friction) values are measured with a load cell and ...

    By Pagani Geotechnical Equipment s.r.l. based in Calendasco, ITALY. from Other Product line

  • Cone Penetration Test (CPT)

    The cone penetration test (CPT) is an in situ testing method used to determine the geotechnical engineering properties of soils and delineating soil stratigraphy. The test method consists of pushing an instrumented cone tip first into the ground at a controlled rate (usually 2 centimeters/second). The resolution of the CPT in delineating ...

    By Zebra Environmental Corporation based in Lynbrook, NEW YORK (USA).

  • Cone Penetration Testing Equipment

    Gregg Drilling & Testing, Inc. (Gregg) offers a wide range of geotechnical and environmental cone penetration testing (CPT) and geophysical testing equipment. Cone penetration testing is a process whereby soil characteristics are determined when a cone penetrometer is driven into the subsurface. The CPT provides a rapid, reliable and ...

    By Gregg Drilling & Testing, Inc. and Gregg In Situ, Inc. based in Signal Hill, CALIFORNIA (USA).

  • ROSON - Model 300 m - Cone Penetration Test Equipment (CPT)

    For water depths between 30 and 300 m the near-shore ROSON is a suitable solution. This ROSON is available with 50 kN, 100 kN or 200 kN pushing force. To avoid the investment in a self-tensioning winch, data communication runs over a free hanging cable to the Icontrol data logger. At water depths up to 30 m a jack-up barge or pontoon is often ...

    By A.P. van den Berg based in Heerenveen, NETHERLANDS. from Near & Offshore Cone Penetration Test Equipment (CPT) Product line

  • ROSON - Model 1,500 m - Cone Penetration Test Equipment (CPT)

    The various ROSON systems come with an electric driven winch with self-tensioning for heave compensation. A CPT depth up to 50 m is feasible. Data communication from the ROSON to deck level is achieved by a powerline connection through the umbilical. This is realized by a transducer at both ends of the umbilical. These transducers, called Icone ...

    By A.P. van den Berg based in Heerenveen, NETHERLANDS. from Near & Offshore Cone Penetration Test Equipment (CPT) Product line

  • Geonor - Model G-200 - Fall Cone Penetration Test - Fall Cone Apparatus

    A new model of the Geonor G-200 Fall Cone Penetration Test including a robust special purpose transport box and a flexible magnifier is now available.ApplicationThe Fall Cone Penetration, first introduced in 1915, provides a rapid, simple and accurate method for determining empirically the undrained shear strength, the shear strength of remolded ...

    By Geonor AS based in Østerås, NORWAY. from Geonor Fall Cone Apparatus Product line

  • Manta - Model 200 - Seabed Cone Penetration Test System (CPT)

    The Manta-200 represents the latest generation Cone Penetration Test (CPT) system for determining offshore seabed soil conditions. Deployed from a steady positioned vessel or platform, the Manta-200 is designed for rapid and reliable results.

    By Geomil Equipment B.V. based in MC Moordrecht, NETHERLANDS. from Near & Offshore Product line

  • Lizard - Model 200 - Hitch-up Cone Penetration Testing System (CPT)

    The Geomil Equipment Lizard-200 is a hitch-up Cone Penetration Testing (CPT) system to be used in combination with an excavator. It allows for conducting CPT’s in near to impossible conditions, such as sites where space is limited and ground anchors cannot be used.

    By Geomil Equipment B.V. based in MC Moordrecht, NETHERLANDS. from Near & Offshore Product line

  • Premium

    AMS - Dynamic Cone Penetrometer

    The most widely accepted, portable method for evaluating strength and density of soil, in situ. The dynamic cone penetrometer uses a 15 lb. (6.8 kg) drive mass falling 20 in. (50.8 cm) that strikes the anvil to cause penetration of 1.5 in (3.8 cm) diameter cone (45 degree vertex angle) that has been seated in the bottom of a pre-augered hole. The ...

    By Art’s Manufacturing and Supply, Inc. (AMS Inc.) based in American Falls, IDAHO (USA). from Geotechnical Sampling and Testing Product line

  • Electric Conductivity Sensor (ECPT)

    With the ECPT sensor you measure the conductivity of the soil while performing standard CPTU test. Test results can be used for analysing salinity and detection of pollutants. The electric conductivity sensor is mounted on Geotechs 10 cm2 CPTU probes. The adapter consists of an array of four ring electrodes (Wenner configuration, i.e. with equal ...

    By Ingenjörsfirman Geotech AB based in Askim, SWEDEN. from Cone Penetration Test (CPT) Product line

  • ConeTec - Cones and Data Acquisition Systems

    All ConeTec cones and data acquisition systems are built seismic ready. The addition of geophones in the CPTu body enables the collection of seismic wave data, and the calculation of shear (Vs) and compressional (Vp) wave velocities during the cone penetration test.

    By ConeTec based in Richmond, BRITISH COLUMBIA (CANADA). from Cone Penetration Testing Product line

  • CPT Track Truck

    The versatile high-performance CPT unit was invented by A.P. van den Berg and has a track record of more than 25 years. With its tracks retracted, the Track-Truck can run on the highway as an ordinary truck. After lowering the tracks, the Track-Truck is in its element in soft and hilly terrain where other heavy ...

    By A.P. van den Berg based in Heerenveen, NETHERLANDS. from Onshore Cone Penetration Test Equipment (CPT) Product line

  • CPT Morooka Crawler

    A CPT Crawler that is based on an existing crawler vehicle is the CPT Morooka Crawler, a relatively fast CPT Crawler for very soft soil. The unit is built on a low ground pressure 15-ton crawler chassis. The rig is fast (with speeds of over 12 km per hour) and can travel long distances on asphalt or concrete surfaces ...

    By A.P. van den Berg based in Heerenveen, NETHERLANDS. from Onshore Cone Penetration Test Equipment (CPT) Product line

  • Mini CPT Crawler

    The most compact & lightest self-propelled unit is the Mini CPT Crawler. The Mini CPT Crawler consists of the well-proven single cylinder HYSON 100 kN-LW with 10 ton pushing force. With a weight well under 1,600 kg and a width of only 780 mm the Mini CPT Crawler fits trough a doorway and can be transported in a mini van. The pusher is ...

    By A.P. van den Berg based in Heerenveen, NETHERLANDS. from Onshore Cone Penetration Test Equipment (CPT) Product line

  • Midi CPT Crawler

    The Midi CPT Crawler is a compact and manoeuvrable CPT system, with a maximum power of 20 tons. The Midi CPT Crawler consists of the renowned CPT penetrometer (HYSON 200 kN) mounted on an undercarriage with rubber tracks. With a weight of about 3,500 kg and a width of only 1200 mm the Midi CPT Crawler fits trough small passages and can be ...

    By A.P. van den Berg based in Heerenveen, NETHERLANDS. from Onshore Cone Penetration Test Equipment (CPT) Product line

  • CPT Truck

    The A.P. van den Berg CPT Truck is a vehicle suitable for soil investigations in pushing capacities from 140 to 200 kN or even more.  A.P. van den Berg has more than 40 years’ experience in manufacturing CPT Trucks based on many diff erent trucks and models. The all-wheel drive 6x6 model has proven most popular ...

    By A.P. van den Berg based in Heerenveen, NETHERLANDS. from Onshore Cone Penetration Test Equipment (CPT) Product line

  • CPT Crawler

    The CPT Crawler provides the same high production rates and reliability as the CPT Truck, with the advantage of tracks for better manoeuvrability in rough or soft terrain. The crawler is the only option at sites where the maximum allowed height is limited. Of course a separate carriage is required for transport of the ...

    By A.P. van den Berg based in Heerenveen, NETHERLANDS. from Onshore Cone Penetration Test Equipment (CPT) Product line

  • Premium

    AMS - Eijkelkamp Penetrologger Kit

    The penetrologger has been especially developed to measure the resistance to penetration of the soil and to save the measuring results to digitally process them on a computer. The penetrologger is ergonomically designed, and lightweight. It can be used to measure to a depth of 80 cm. The penetrologger can provide the Unified Soil Classification ...

    By Art’s Manufacturing and Supply, Inc. (AMS Inc.) based in American Falls, IDAHO (USA). from Geotechnical Sampling and Testing Product line

  • Premium

    AMS - Dual Mass DCP

    Developed by the Army Corps of Engineers, Dynamic Cone Penetrometers (DCPs) provide a low-cost, efficient test method for quickly determining in-situ CBR values of pavement base, subbase and subgrades. They can readily be used for depths up to 30' and up to 6' with optional drive rods and extensions. This model complies with ASTM D6951 ...

    By Art’s Manufacturing and Supply, Inc. (AMS Inc.) based in American Falls, IDAHO (USA). from Geotechnical Sampling and Testing Product line

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you