Cooling Tower Component Equipment
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
In the manufacturing process we developed the foils are reinforced at the outer edges and in the middle and are therefore very stable. This makes our film fill media extraordinarily resistant to erosion. Our unique welding method connects the single foils with up to 20.000 welding points per m3. This high number of connections results in robust packings with high mechanical load capacity. Bearing ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
in the cooling circuit to prevent the formation of deposits and bacterial growth, 2H SANIPACKING drift eliminators serve to minimize the risk of infections from legionella ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
Our 2H Splash and Trickle Fills have been specially designed for medium to strongly polluted cooling water, the focus of the development being on a high stability as well as on easy and economical installation. Therefore these fills are built from mechanically joint grids and are easily cleaned. The 2H NET 150 grid packings are ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
treatment in the cooling circuit to prevent the formation of deposits and bacterial growth, 2H SANIPACKING fills serve to minimize the risk of infections from legionella ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
Reduction Of Risk Of Legionella Pneumophila In Open Cooling Circuits; Time and again news report about outbreaks of legionella disease in areas near cooling towers. Careful water treatment, together with regular maintenance reduces the risk of bacteria growth in the cooling circuit. But one step more leads to an even higher ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
Different Types For All Requirements – Available In PVC And PP; From small cooling towers to large cell and natural draught cooling towers: Our PLASdek packings fulfill all requirements. Different types of film fills with large specific surface are highly suited for clean and medium water qualities, whereas for special ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
In all different types of cooling towers drift eliminators are used to reduce the loss of water and emissions. Above the water distribution and the cooling fills, a layer of drift eliminators is installed for this purpose. It catches the water drops which are carried away with the air flow and redirects them into the cooling ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
Optimal heat transfer properties – low pressure drop; Generally, every cross fluted fill could be cut to be installed in a cross-flow cooling tower. Such a fill, however, would not perfectly fit the requirements; we therefore developed a special range of fill for this type of tower (FX12.12 or KSN with a drift eliminator section KSA and ...
-
Manufactured by Amertech Tower Services, LLC. (ATS)based in USA
Field Erected Industrial Cooling Towers are constructed from various materials including preservative treated lumber and plywood, glass fiber reinforced pultrusions, steel and even reinforced concrete. Not matter which material you are dealing with, ATS can help fulfill your needs. ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
Our cellular inlet louvres improve the air flow into the cooling tower. They not only hold back unwanted elements (e.g. leaves) but also prevent water splash-out which can cause icing and loss of expensive water and treatment chemicals. Moreover, an inlet louvre restricts the amount of sunlight entering the cooling tower thereby ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
Our 2H Splash and Trickle Fills have been specially designed for medium to strongly polluted cooling water, the focus of the development being on a high stability as well as on easy and economical installation. Therefore these fills are built from mechanically joint grids and are easily ...
-
PremiumManufactured by Brentwood Industries, Inc.based in USA
2H PLASdek and CLEANdek vertical flow fills are designed for the use in counterflow cooling towers with poor water quality. With different types in PP, PVC and PPHT and different material thickness, our fills cover all customer requirements. Fill media in flame retardant or anti-bacterial types are available on request. 8earing capacity and ...
-
Manufactured by SG Cooling Towerbased in INDIA
The evaporative cooling process causes almost all cooling towers to lose water to the outdoors. In Drift Eliminator The most common kind of evaporation is pure water vapor , which has no negative impact on the environment. The unintended/unwanted loss of liquid water to the environment caused by microscopic droplets entrained in the outgoing ...
-
Manufactured by SG Cooling Towerbased in INDIA
Splash fills increase the amount of air that comes into touch with the water’s surface. Splash fills, rather than a sheet surface, increase the surface area of the water droplets. The splash fill breaks up the water into tiny droplets, exposing more water surface to the wind. Additionally, the splash fill keeps the water suspended for a longer amount of time, allowing for more exposure to ...
-
Manufactured by SG Cooling Towerbased in INDIA
A reliable cooling tower louver is necessary for a cooling tower system to perform effectively. Its efficient operations increase the quality and amount of water. In a cooling tower, water and air are mixed together. In other words, a specific collection of undesirable circumstances is highly ...
-
Manufactured by SG Cooling Towerbased in INDIA
We are leading PVC Fills manufacturer in India. To satisfy industrial special needs, S. G offers a wide selection of edge folded PVC fill materials. The criteria for counter flow cooling towers are met by our standard fill products. Our fillers have both edges folded, resulting in a large surface area per volume. S.G PVC Fills are ...
-
Manufactured by Cooldeck Industries Pvt. Ltd.based in INDIA
Virgin and reprocessed PVC made Film Fills are cooling Tower Components. These are accessible in 1200 mm x 600 mm , 600 mm x 600 mm and 600 mm x 300 mm size choices. Longitudinal pitch of these fills is 37.5 mm and their flute height is 12 mm. Standard weight of these Film Fills is 26.5 kg/m3. Per unit volume of their surface area is 258 ...
-
Manufactured by Cooldeck Industries Pvt Ltdbased in INDIA
CD-S130/146, made out of rigid PVC, is designed to remove maximum entrained drift particles from air stream efficiently, with minimum pressure drop, thereby reducing the fan power ...
-
Manufactured by Cooldeck Industries Pvt Ltdbased in INDIA
The V-Bar system has proven to be a superior system to upgrade Cross Flow cooling towers that have wood splash fill and for new construction NDCT and IDCTs where dirty water would clog film ...
-
Manufactured by Cooldeck Industries Pvt Ltdbased in INDIA
inert PVC ensures longer life of the fills as compared to other cooling pads such as wood and ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you