High efficiency, high solidity impellers for use in turbulent side entering applications. They are especially effective for fluids possessing a yield value, such as paper stock. The high solidity permits operation nearer the boiling point without cavitation.
The JT-2 Impeller has been developed for superior blending in transitional flow. Higher viscosity and non-Newtonian fluids make blending much more challenging. This impeller is used after conventional turbines have lost efficiency due to viscous effects and before the need for close clearance impellers.
A cost effective impeller for operation very near the floor of a tank for agitating the heel in solids suspension applications. Also an effective impeller in laminar flow applications, especially when impeller Reynolds numbers drop below 50.
A reasonably cost effective impeller in both turbulent and laminar flow. Good impeller for applications where the viscosity changes over a wide range causing the flow regime to vary between turbulent and laminar flow. A reasonably cost effective impeller for solids suspension.
The Chemineer RL-3 impeller is designed for applications where a ragless agitator is desired to prevent fibrous material build-up on the rotating impeller. Typical in Waste Treatment applications the RL-3 is a rag shedding impeller which prevents build-up of fibrous materials on the impeller, while providing a strong axial flow for efficient ...
The CD-6 impeller is a second generation gas and immiscible liquid dispersion impeller. The CD-6 can handle about 2.4 times the maximum gas capacity of the D-6 impeller. The CD-6 is similar to the Smith impeller, but there are substantial power and dispersion capability differences. This impeller has been used at aeration numbers as high as 2.1.
The highest efficiency turbulent flow impeller available in the marketplace. Ideal for blending, heat transfer, and solids suspension applications. Developed to maximize strength at lower weights as compared to other axial flow impellers, allowing for longer shafts without internal support, smaller shaft diameters, and smaller seal sizes if ...
An extremely efficient turbulent flow impeller for blending, heat transfer and solids suspension. Most effective for Reynolds numbers over 50. Developed to minimize the creation of trailing vortices and incorporating the otherwise wasted energy into macro-flow.
The ‘WQ’ pump are suitable for clear and waste water, also for sewage and sludge containing solids and fibrous material. The pump suitabe for wet installtion and vertical dry installation thanks to cooling jacket design.
The Chemineer® SC-3 Impeller features an advanced design engineered for deep tanks. It produces flow characteristics of much larger impellers, without the added weight, or the resulting loss in pumping efficiency. The highly efficient SC-3 Impeller's reduced weight allows for the use of longer shaft extensions for deeper tanks, and resolves ...
Extremely versatile in its applications, the impeller provides efficient handling of a range of liquids, often highly abrasive or corrosive in nature. It is ideal for: Solids Handling, Pumping Viscous Sludges, Handling Delicate or Low Shear Products.
Ceramic slurry pump impellers are made of Silicon Nitride Bonded Silicon Carbide, aimed to Wear and Erosion resistant working application.Partial list of Impellers available for the contemporary and legacy OEM stylesWarman AH slurry pump impellers style1.5 /1 2 /1.5 3 /2 4 /36 /4 8 / 6
Pump impeller is one of the most important pump parts. Only the pump impeller works well,then the slurry pump could meet requirements. However, it is an easlily worn-out pump parts. Therefore, material plays an important role for its lifetime. Pump Impeller 1.Our pump impeller has excellent wear resistance, corrosion resistance large passage area ...
Used for clear wastewater, rainwater and seepage containing small amounts of sand. The considerable manometric head makes these units suitable for irrigation and the fish processing sector. General features: Deliveries GAS 1' 1/2. Motor poles 2. Passages 7 mm. Powers 0,9 kW. High head impeller.
Suitable for lifting soiled wastewaters containing filaments or fibres, and unstrained household sewage in general. General features: Deliveries GAS 1' 1/2. Motor poles 2. Passages - mm. Powers 0,9 kW. Impeller with grinder system.
Recommended for unstrained civil wastewaters, including those containing filaments or fibres. This electric pump is intended for both domestic and professional use. General features: Deliveries GAS 1' 1/2. Motor poles 2. Passages - mm. Powers 0,74 ÷ 1,5 kW. Impeller with grinder system.