Impeller Pump Equipment Near Indonesia
-
PremiumManufactured by Lutz Pumpen GmbHbased in GERMANY
Powerfull and robust immersion centrifugal pump with plain bearing, support stand mounted on roller bearings and IEC standard motor. The B80 KGK G3 series is available in single- or two-stage versions equipped with one or two impellers for high pump ...
-
Manufactured by Aqua-Aerobic Systems, Inc. - a subsidiary of the METAWATER Groupbased in USA
The AquaDDM Mixer provides maximum wastewater mixing efficiency. When mixing requirements are the controlling factor, the AquaDDM mixer can reduce power costs, while delivering 3-4 times the mixing of any aerator of the same size. The ducted impeller improves pumping efficiency. The integrated flow vanes and lower input torque eliminate the ...
-
PremiumManufactured by Lutz Pumpen GmbHbased in GERMANY
Suitable for recirculation of chemicals and etchants, emtying of containers and basins, ...
-
PremiumManufactured by Lutz Pumpen GmbHbased in GERMANY
Liquid examples: Battery acid, ferric sulphate, glycol, phosphoric acid, hydrochloric acid, citric acid, ...
-
PremiumManufactured by Landustrie Sneek BVbased in NETHERLANDS
Our LANDY submersible DCP pump with open channel impeller is ideally suited for slightly contaminated wastewater. This high efficient pump is featured by a compact design, high pressure and non-clogging performance. ...
-
PremiumManufactured by Landustrie Sneek BVbased in NETHERLANDS
Our LANDY closed screw impeller pumps are ideally suited for situations where power consumption is an important issue. This type of impeller is the new generation single channel impeller performing with high efficiency and good non-clogging ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
The Chemineer RL-3 impeller is designed for applications where a ragless agitator is desired to prevent fibrous material build-up on the rotating impeller. Typical in Waste Treatment applications the RL-3 is a rag shedding impeller which prevents build-up of fibrous materials on the impeller, while providing a strong axial flow ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
A cost effective impeller for operation very near the floor of a tank for agitating the heel in solids suspension applications. Also an effective impeller in laminar flow applications, especially when impeller Reynolds numbers drop below ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
A reasonably cost effective impeller in both turbulent and laminar flow. Good impeller for applications where the viscosity changes over a wide range causing the flow regime to vary between turbulent and laminar flow. A reasonably cost effective impeller for solids ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
The Chemineer® SC-3 Impeller features an advanced design engineered for deep tanks. It produces flow characteristics of much larger impellers, without the added weight, or the resulting loss in pumping efficiency. The highly efficient SC-3 Impeller's reduced weight allows for the use of longer shaft extensions for deeper ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
An extremely efficient turbulent flow impeller for blending, heat transfer and solids suspension. Most effective for Reynolds numbers over 50. Developed to minimize the creation of trailing vortices and incorporating the otherwise wasted energy into ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
The JT-2 Impeller has been developed for superior blending in transitional flow. Higher viscosity and non-Newtonian fluids make blending much more challenging. This impeller is used after conventional turbines have lost efficiency due to viscous effects and before the need for close clearance ...
-
Manufactured by Fluid Equipment Development Company (FEDCO)based in USA
Hydraulic pressure boosters or HPBs capture pressure from a secondary flow to boost the primary high pressure feed flow. Our equipment provides the lowest cost ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
The CD-6 impeller is a second generation gas and immiscible liquid dispersion impeller. The CD-6 can handle about 2.4 times the maximum gas capacity of the D-6 impeller. The CD-6 is similar to the Smith impeller, but there are substantial power and dispersion capability differences. This impeller has been used at ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
A high efficiency, advanced side-entering hydrofoil impeller that produces maximum pumping action. It has more cavitation resistance than other designs through effective hydrodynamic ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
High efficiency, high solidity impellers for use in turbulent side entering applications. They are especially effective for fluids possessing a yield value, such as paper stock. The high solidity permits operation nearer the boiling point without ...
-
Manufactured by National Oilwell Varco (NOV)based in USA
The highest efficiency turbulent flow impeller available in the marketplace. Ideal for blending, heat transfer, and solids suspension applications. Developed to maximize strength at lower weights as compared to other axial flow impellers, allowing for longer shafts without internal support, smaller shaft diameters, and smaller seal ...
-
Manufactured by Zenit Europe S.A.based in LUXEMBOURG
Used for clear wastewater, rainwater and seepage containing small amounts of sand. Its high manometric head makes this series suitable for the creation of water features and decorative fountains. This electric pump is intended for both domestic and professional use. General features: Deliveries 1' 1/2. Motor poles 2. Passages 6 mm. Powers ...
-
Manufactured by Zenit Europe S.A.based in LUXEMBOURG
The ideal solution for use with clear or slightly soiled wastewaters containing small solids, strained water, rainwater, seepage and water pumped from underground. Suitable and reliable for domestic use, including heavy-duty applications. General features: Deliveries GAS 1' 1/4. Motor poles 2. Passages 7 mm. Powers 0,3 ÷ 0,74 kW. ...
-
Manufactured by Zenit Europe S.A.based in LUXEMBOURG
Recommended for unstrained civil wastewaters, including those containing filaments or fibres. This electric pump is intended for both domestic and professional use. General features: Deliveries GAS 1' 1/2. Motor poles 2. Passages - mm. Powers 0,74 ÷ 1,5 kW. Impeller with grinder ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you