waste transfer equipment in United Kingdom

  • ACP - Precast Concrete Waste Transfer Walls

    ACP Concrete Ltd's precast concrete wall panel system is a fast track construction method for push walling / thrust walls to waste transfer stations. Interlocking prestressed horizontal concrete panels span between steel support columns to produce foundation free, uniform, smooth, robust push walls. Precast vertical wall panels can be used to ...

    By ACP (Concrete) Ltd. based in Cumbria, UNITED KINGDOM. from Precast Concrete Waste Transfer Walls Product line

  • Eureka - Permanent Transfer System (PTS)

    The first commercially manufactured heat recoverer in Europe utilises the waste heat from refrigeration plant which generates free potable hot water. This is heated to a high temperature and pasteurised at the same time. Plant room temperatures are lowered and compressor run-time is reduced.

    By Eureka Heat Recovery Systems Ltd based in Conisbrough, UNITED KINGDOM.

  • High-Tip : Reception/Transfer Container

    The cost of transporting dewatered sludge to landfill sites can be reduced significantly if you choose the MOOS High Tip System for on site accumulation of for example dewatered sludge from the jet-vac, tankers, MOOS KSA system etc. The dewatered waste which has remained in the initial High Tip reception container will at some point accumulate and ...

    By Simon Moos Maskinfabrik A/S Office in York North Yorkshire, UNITED KINGDOM.

  • Model XiLog+ - 3G, GPRS and SMS Communications Data Loggers

    XiLog+ is an advanced range of data loggers with remote communication options. It is available in single to nine channel models for use with a wide variety of sensors for clean and waste water network monitoring. Data is available via PrimeWeb.

    By Primayer Ltd based in Denmead, UNITED KINGDOM. from 3G, GPRS and SMS Communications Data Loggers Product line

  • Powerkrush - Model 2000WTS - Transfer Station

    The Powercrush 2000 is our largest sized Transfer Station with a capability of handling 507 cubic metres per hour of waste with a swept volume of 7.76 cubic metres, making this powerful compactor a natural choice in the design of high volume Refuse Transfer Stations. This extremely powerful compactor is capable of transfer loading huge amounts of ...

    By Pakawaste Ltd based in Preston, UNITED KINGDOM. from Transfer Station Product line

  • Powerkrush - Model 1000WTS - Transfer Station

    The Powerkrush 1000 is our medium sized Transfer Station. It has a capability of handling 372 cubic metres per hour of general mixed waste with a swept volume of 5.18 cubic metres, making this powerful compactor a natural choice in the design of medium volume Refuse Transfer Stations. Massive sections are used throughout to ensure that no ...

    By Pakawaste Ltd based in Preston, UNITED KINGDOM. from Transfer Station Product line

  • bmi - Mobile Transfer Trailers

    43m3, with Alpha-III rear self loading tailgate. For transport of co-mingled recyclates, domestic refuse, green waste and organic food waste. Reduce the need for vehicles to have to return to depot and tip load by loading to the Mobile Transfer Trailer first.

    By The bmi Group based in Dungannon, UNITED KINGDOM. from Mobile Transfer Trailers Product line

  • UK Waste - Model 400 - Static Waste Compactor

    The UK Waste Model 400 Series comprises of single and twin ram waste compactors. They have been specifically manufactured to work with high volume waste operations where large bulky materials may be loaded with loading shovels or grabs. The equipment is ideally suited to work with local Civic Amenity Sites and Transfer Stations.

    By UK Waste & Recycling Ltd. based in Liverpool, UNITED KINGDOM. from Static Waste Compactor Product line

  • Hydratech Toploader - Reliable Waste Processing System

    Effective transfer of alternative fuels from road transport and into a process is often given little consideration. It is not unusual for sites to rely on tipping material onto a floor and using front loaders to move the material around. Not only is this inefficient but it can also become dangerous when multiple vehicles become involved. A much ...

    By Renby Limited based in Tarvin, UNITED KINGDOM.

  • Airmec - Rotary Valve

    Airmec Rotary Valves are large diameter, heavy duty units designed exclusively for handling paper, and board waste, they should not be confused with smaller lightweight units which have a tendency to jam when passing large volumes of material. Each of its rotor blades is fitted with a wear resistant seal (not the more common canvas backed rubber) ...

    By Airmec Design Limited based in Market Drayton, UNITED KINGDOM.

  • Skip Station

    Screw conveyors are utilised to transfer solid waste or slurry from solids control equipment to drilling waste containers, barges or to a point of treatment such as a Slurrification Unit for drill cuttings reinjection.

    By Screw Conveyor Limited based in Aberdeen, UNITED KINGDOM.

  • Rotary Valve

    The RotaryValve is a robust unit designed to deliver large quantities of waste into a baler or compactor feed hopper without transfering air pressure.

    By Paramount Waste Extraction Ltd. based in Camberley, UNITED KINGDOM.

  • GN Solids - Model GNSC - Screw Conveyor/Auger

    Screw conveyor/ Auger is type of equipment widely used on oil field and waste management yards as a transferring device. According to specific requirements, several units can be located head to end, transferring waste cuttings through the conveyor groove to the drying equipment (i.e. a vertical cutting dryer). By being designed with a wider hopper ...

    By GN Solids Control UK based in Kent, UNITED KINGDOM. from Screw Conveyor/Auger Product line

  • Feeders

    Vibrating Feed Stations, Rugged high-stroke Vibratory Feeder designed for efficient transfer of material. Incorporating a durable high capacity feed hopper, supported on a rigid structure. Ideal for skip waste or construction and demolition waste.

    By Smulders Waste Technology B.V. (SWT) Office in Frome, UNITED KINGDOM. from Feeders Product line

  • TransPak Precompaction System

    The Harris TransPak Precompaction System makes the process of loading and transferring solid waste by road, rail or barge easy, efficient and clean by producing load-sized, untied, densified bales of solid waste and other recyclable material.

    By Harris Waste Management Group, Inc Office in Glos, UNITED KINGDOM.

  • Model Series G - Horizontal Pumps

    Self-priming centrifugal pumps for transfer and recirculation of: chemical solutions / waste treatment photographic solutions (inorganic). Material: Noryl, PPS - Plastic. Performance: 10-100 gpm.

    By Serfilco International Ltd Office in Irlam, UNITED KINGDOM. from Horizontal Pumps Product line

  • Sydex - Model FM range - Compact Progressing Cavity Pumps

    Extremely popular compact free molded design progressing cavity pump , maximum capacity in the minimum of space with suction lift capabilities. Ideal for waste water, marine and transfer duties.

    By Sydex srl Office in Eastleigh, UNITED KINGDOM.

  • Model Series SP - Self-Priming Centrifugal Horizontal Pumps

    Self-priming centrifugal pumps for transfer and recirculation of: Chemical solutions, waste treatment, agricultural solutions, ground water. Material: Cast iron - Metal. Performance: 20-140 gpm.

    By Serfilco International Ltd Office in Irlam, UNITED KINGDOM. from Self-Priming Centrifugal Horizontal Pumps Product line

  • Renby Spirofloor - Moving Floor Bunkers

    As waste management moves near the top of the environmental agenda, investment in more efficient waste handling equipment has become a priority. For example, owing to the cost of double-handling tipped material, more and more waste recycling companies are refusing to accept tipper trucks. Bulk waste transport companies must transfer material ...

    By Renby Limited based in Tarvin, UNITED KINGDOM.

  • Chemineer - Model HE-3 - High-Efficiency Impeller Pump

    An extremely efficient turbulent flow impeller for blending, heat transfer and solids suspension. Most effective for Reynolds numbers over 50. Developed to minimize the creation of trailing vortices and incorporating the otherwise wasted energy into macro-flow.

    By National Oilwell Varco Office in UNITED KINGDOM. from High-Efficiency Impeller Pump Product line

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you