Sauereisen - Model No. 220 & 221 - Epoxy Joint Sealants
Sauereisen Epoxy Joint Sealants are used to provide a durable joint filler. The materials are 100% solids, pourable epoxies designed to effectively absorb the shock and impact of heavy loads and steel-wheeled vehicles over narrow joints. Available in two formulations, No. 220 is for general purpose applications and No. 221 is a NovolaK epoxy for more severe chemical environments. Sauereisen Joint Sealants are non-shrinking due to their high-solids content and will not become brittle. These self priming materials will flow and self-level to the full depth of the joint. The joint compounds cure quick enough to be ready for foot traffic in 24 hours and chemical service in 3 days. To use in vertical joints, add 1/2 to 1 pound of Thixotrope No. 220T (sold separately) to each unit of joint material and mix thoroughly. This results in a viscosity suitable for a caulking gun.
Physical properties were determined on specimens prepared under laboratory conditions using applicable ASTM procedures. Actual field conditions may vary and yield different results; therefore, data is subject to reasonable deviation.
- Absorbs heavy loads.
- Resists chipping and wear at joint edges.
- Pourable and self-leveling.
- Requires no primer.
- Cures on damp surfaces.
Temperature of Working Area
Maintain a temperature of 60°-90°F on air, substrate and Epoxy Joint Compounds during mixing, application and cure. Material components should be maintained at 60°-90°F for 48 hours prior to use.
The substrate should be made free of oil, grease, laitance and other contaminants that may inhibit the bond of the joint compound. Chemical cleaning is recommended. All surfaces must be firm and structurally sound as specified by the architect/engineer. Any loose particles of dust, dirt or foreign matter should be removed by brushing or vacuuming.
Nos. 220 & 221 are packaged as premeasured, 1-gallon units containing two components - Liquid and Hardener -
which are mixed 1:1 by volume as used.
Completely empty contents of Hardener into Liquid component and mix thoroughly for three to five minutes using a slow-speed (150 rpm) paddle-type mixer. Avoid entrapment of air while mixing.
Do not add water, sand or any other adulterant to either component or the mixed compound unless specifically recommended by Sauereisen. Upon completion of mixing, the joint material is ready for use.
A bond breaker should be installed in the bottom of the joint prior to pouring No. 220/221. Polyethylene foam backer rods that are 50% wider than the width of the joint should be forced down to the substrate for this purpose. Where the
joint depth is less than 1/2 inch, vinyl electrical tape should be installed at the bottom of the joint to prevent bonding to the substrate. Pour the mixed joint compound into the clean, dry joint.
As a general rule, the depth of the material in the joint should be maintained at approximately 50% of the joint width in
order to provide the right combination of elongation and corrosion resistance. For applications where joints are very deep, additional layers of backer rods should be used.
For vertical applications, tape the open joint and then pour the No. 220/221 behind the tape. Do not attempt to pour more than 12 inches of material behind the tape. As the application moves up the wall, the procedure is repeated; applying tape and then pouring behind the tape.
The tape is left in place until curing takes place. As an alternative, approximately 1/2 to 1 gallon of Additive No. 220T may be added to each unit of mixed joint compound and blended thoroughly. This results in a material grade that may be applied with a caulking gun.
For deteriorated joints, repair the surrounding protective system with the proper Sauereisen material. The repair material should be 'keyed in' by sawcutting beyond the spalled concrete on both sides of the joint and mechanically removing the loose concrete. The joint should be reformed when placing the repair material by using a removable spacer; or the deteriorated joint area may be completely sealed with the repair material and a new joint sawcut after it cures. Refill with No. 220/221.
The compounds should be allowed to cure a minimum of 24 hours at 70°F prior to water or foot traffic; 72 hours prior to chemical service. At temperatures below 70°F, cure a minimum of 48 hours prior to water exposure or foot traffic.
220 & 221 are two-component materials packaged in a carton as follows:
- Liquid: 1 gallon can
- Hardener: 1 gallon can
Each container is partially filled to provide an approximate gallon of joint sealant material when mixed.
Epoxy Joint Compounds have a shelf life of one (1) year when stored in unopened, tightly sealed containers in a dry location at 70°F. If there is doubt as to the quality of the materials, consult a Sauereisen representative.
Consult Safety Data Sheets and container label Caution Statements for hazards in handling these materials.
The width is equal to two times the depth..... ( Width = 2 x Depth )
All equipment should be cleaned with MEK or N-methyl pyrol before joint compound cures. If removal is required after cure, consult Sauereisen for recommendations.
We warrant that our goods will conform to the description contained in the order, and that we have good title to all goods sold. WE GIVE NO WARRANTY, WHETHER OF MERCHANTABILITY, FITNESS FOR PURPOSE OR OTHERWISE, EXPRESS OR IMPLIED, OTHER THAN AS EXPRESSLY SET FORTH HEREIN. We are glad to offer suggestions or to refer you to customers using Sauereisen cements and compounds for a similar application. Users shall determine the suitability of the product for intended application before using, and users assume all risk and liability whatsoever in connection therewith regardless of any suggestions as to application or construction. In no event shall we be liable hereunder or otherwise for incidental or consequential damages. Our liability and your exclusive remedy hereunder or otherwise, in law or in equity, shall be expressly limited to our replacement of nonconforming goods at our factory or, at our sole option, to repayment of the purchase price of nonconforming goods.
- Distributors and agents in major cities throughout the world. Consult manufacturer for locations.
- Information concerning government safety regulations available upon request.
- Sauereisen also produces inorganic compounds for assembling, sealing, electrically insulating and grouting