Sauereisen - Model No. 21C - Furan Resin Mortar Grout
Sauereisen Furan Resin Mortar/Grout No. 21C is a two-component, 100% carbon- filled bonding material for chemical resistant masonry units and quarry tile. No. 21C and chemical-resistant masonry units used with a suitable membrane form a complete system to protect concrete and steel substrates from attack by corrosive chemicals and physical abuse.
No. 21C is used in the construction of floors, sumps, trenches, tanks, vessels and bleach towers in chemical processing; food & beverage plants; dairies; laboratories; textile, steel and pulp & paper mills. No. 21C has excellent resistance to a wide range of acids (including hydrofluoric), alkalies and most solvents up to 350oF. No. 21C is not recommended for exposure to hypochlorites or oxidizing agents such as nitric, chromic acid or sulfuric acid greater than 60%. Refer to Sauereisen's Chemical Resistance Chart for specific service conditions.
- Bond strength1000 psi: 900 psi
- Compressive strength - C579 (7 day): 8000 psi5400 psi
- Density - C905 (7 day): 95.7 pcf93.4 pcf
- Flexural strength - C580 (7 day): 3100 psi2400 psi
- Maximum service temperature: 450°F450°F
- Modulus of elasticity - C580 (7 day): 1.5 x 106 psi8.75 x 105 psi
- % Shrinkage - C531 (7 day): 0.18%0.09%
- Tensile strength - C307 (7 day): 1100 psi1000 psi
- Water absorption - C413 (7 day): 1.18%1.45%
Physical properties were determined on specimens prepared under laboratory conditions using applicable ASTM procedures. Actual field conditions may vary and yield different results; therefore, data are subject to reasonable deviation.
- Low odor Furfuryl Alcohol Polymer.
- Resists a wide range of acids, alkalies and most solvents.
- 100% carbon filled.
- Withstands temperatures to 450oF.
- Authorized by USDA for use in federally inspected meat & poultry plants.
Temperature of Working Area
For optimum application conditions, maintain a temperature of 60o - 80oF on air, substrate, Powder, Liquid, and masonry units during mixing, application, and cure. Maintain materials and substrate between 60oF - 80oF for 48 hours prior to beginning work.
At temperatures below 65oF, the viscosity increases and application becomes more difficult. No. 21C can be applied at temperatures as low as 50oF. Consult Sauereisen for specific recommendations for environments colder than 50oF.
Above 80oF, working time of the material decreases. In higher temperatures it is recommended that the Liquid be cooled by placing the pail in a large container filled with water and ice or storing in a cool area.
All surfaces in contact with No. 21C should be clean, dry, and free of dust, dirt, grease, oil, and other contaminants. Surface prep should be in accordance with membrane requirements.
Empty correct proportion of Liquid into a clean mixing vessel. Gradually add measured amount of Powder while mixing continuously with a trowel or hoe until mortar is uniformly blended to a workable consistency. After mixing do not allow mortar to remain in the mixing vessel, spread mortar in a thin layer in a mortar pan to ensure maximum working time of 30 minutes at 73oF. Recommended mix ratio, parts by weight, is as follows:
- Parts: by weight
- Mortar: 1.9 1
- Grout: 1.5 1
Material which has begun to set cannot be retempered and must be discarded. Never add Liquid or other materials to mixed material or any component part.
Bricklayer's Method - Trowel an average 1/8-inch thick bed joint of 21C directly on top of the membrane or preceding course of brickwork. Apply the mortar by buttering one side and one end of each brick with a pointing trowel. Set the masonry units in place and position by tapping to form an average 1/8-inch wide vertical joint.
Tilesetter's Method - The masonry units or quarry tile must have waxed faces. Place a quantity of the grout onto the surface of previously set masonry units or quarry tile. Spread and work grout across surface of the tile at a 45° angle to the joints using an American Olean K&R trowel. When filling the joints in this manner, take special care to work the grout to full depth of the joint.
Bricklayer's Method - Strike extruded mortar off face of masonry unit with a trowel. For floors where appearance is a factor, waxed units are recommended.
Tilesetter's Method - After filling the joints, remove the excess mortar from the surface of the masonry units or quarry tile using the trowel as a squeegee. After masonry units or quarry tile have achieved a full cure - 3 days at 73°F - remove wax using a steam lance with 60psi (minimum) pressure at the nozzle.
All equipment should be cleaned with acetone or MEK before 21C cures. If removal is required after cure, consult Sauereisen for recommendations.
Estimating Table - material quantities per square foot.
The above quantity requirements are based upon physical dimensions of chemical-resistant masonry units and actual weight of mortar as determined by ASTM C-905. Actual usage rate will vary dependent upon scope of installation, experience of workmen, field conditions and other contingencies. Personnel using the above chart should, therefore, add an appropriate wastage factor.
21C is self-hardening due to a chemical reaction which occurs when the Powder and Resin are mixed together. An initial set occurs in 4 to 4 1/2 hours at 70° F - the material is ready for service after a 24-hour cure at 70°F. Brickwork should not be subject to water, steam, or chemical environment before the mortar is completely cured.
Joints are to be provided on 20-foot centerlines, around all fixed objects, peripheries of rooms and all points of movement in the base slab. Consult Sauereisen for product recommendation.
21C Furan Resin Mortar/Grout
Liquid: 42.1 lbs. in a 5-gal pail
Powder: (2) 40 lb. bags
Sauereisen Furan Resin Mortar/Grout 21C Liquid and Powder have a shelf life of one (1) year when stored in unopened, tightly sealed containers in a dry location at 70°F. Avoid freezing. If there is a doubt as to the quality of the materials, consult a Sauereisen representative.
Consult Safety Data Sheets and container label Caution Statements for hazards in handling these materials.
We warrant that our goods will conform to the description contained in the order, and that we have good title to all goods sold. WE GIVE NO WARRANTY, WHETHER OF MERCHANTABILITY, FITNESS FOR PURPOSE OR OTHERWISE, EXPRESS OR IMPLIED, OTHER THAN AS EXPRESSLY SET FORTH HEREIN. We are glad to offer suggestions or to refer you to customers using Sauereisen cements and compounds for a similar application. Users shall determine the suitability of the product for intended application before using, and users assume all risk and liability whatsoever in connection therewith regardless of any suggestions as to application or construction. In no event shall we be liable hereunder or otherwise for incidental or consequential damages. Our liability and your exclusive remedy hereunder or otherwise, in law or in equity, shall be expressly limited to our replacement of nonconforming goods at our factory or, at our sole option, to repayment of the purchase price of nonconforming goods.
- Distributors and agents in major cities throughout the world. Consult manufacturer for locations.
- Information concerning government safety regulations available upon request.
- Sauereisen also produces inorganic compounds for assembling, sealing, electrically insulating and grouting