Sauereisen Inc.

- Model No. 600/610 - Sulfur Base Mortars Basolit/Carbon Basolit

From

0

Sauereisen 600 and 610 Sulfur-Based Mortars are used for concrete test cylinders and as a compound in the manufacturing of abrasive grinding wheel arbor holes. 600 is also used in the assembly of porcelain ceramic insulators in electrical transmission markets. 600 and 610 Sulfur-Based Mortars have a history of corrosion control when used in the construction of floors, trenches, sumps and tanks in steel mills, mines, metal finishing and chemical-processing plants. 600/610 mortars can be used in accordance with ANSI/ASTM C386, Standard Practice for Use of Chemical- Resistant Sulfur Mortar. 600/610 comply with the requirements of ANSI/ASTM C617, Standard Method of Capping Cylindrical Concrete Specimens.

  • 600 and 610 mortars are manufactured in both ingot/briquette and flake forms. The 600/610 mortars melt rapidly, set quickly - within minutes - and meet most production requirements.
  • 600 is silica-filled, while 610 is carbon-filled for those applications where hydrofluoric acid exposure is encountered. Refer to Sauereisen Chemical Resistance Chart for suitability in specific chemical service.

Physical properties were determined on specimens prepared under laboratory conditions using applicable ASTM procedures. Actual field conditions may vary and yield different results; therefore, data is subject to reasonable deviation.

Temperature of Working Area

Maintain a temperature of 50o on air, brick, substrate, during mixing, application, and cure.

Surface Preparation

All surfaces in contact with No. 600/610 should be clean, dry, and free of dust, dirt, grease, oil, and other contaminants that may inhibit bond of No. 600. Surface prep should be in accordance with membrane requirements.

Melting

600/610 must be melted to a free-flowing state for use. Place a quantity of No. 600/610 into a suitable clean, dry, steel, temperature-controlled kettle and melt to a smooth, free-flowing liquid at 265°F to 290°F. Stir occasionally while melting or when adding more material.

Use a suitable melting pot for sulfur-base compounds equipped with automatic temperature controls.

If heated above 300°F, the material thickens. To reduce viscosity and lower the temperature to optimum range, remove the heating element and/or add additional No. 600/610 material. Overheated material is still usable after temperature has decreased to 260°F - 290°F, provided temperature has not exceeded 300°F.

Capping Plate Preparation

Capping plates should be lightly coated with mineral oil prior to 600 application.

Empty quantity of 600 into melting pot and regulate temperature between 265°F and 290°F. Melt material in this temperature range to a smooth, free-flowing liquid.

Pour the molten 600 into the capping plate with a ladle. Place the concrete cylinder immediately into the sulfur cement and allow to remain until the compound solidifies (approximately one minute). After the compound has solidified, remove the capped cylinder from the mold.

Installation of Walls and Floors

Walls - Set the masonry units on 620 wood spacers and form ¼-inch wide horizontal and vertical joints. Install a single layer at a time and fill joints before proceeding with successive layers. When the exposed joints are to be 600/610, they must be taped with muslin strips saturated in Sauereisen 14 to retain the molten mortar until it congeals. Muslin may be stripped, resaturated and reused as soon as 600/610 Mortar congeals. The pour should stop when the joint is approximately 1/2 inch below the top surface of the masonry unit to provide a key for subsequent courses.

Floors - Using a suitable pouring container, apply a thin layer of 600/610 over membrane to prevent damage prior to brick installation. Set the masonry units on No. 620 wood spacers and align brickwork, maintaining ¼-inch wide vertical joints. Pour molten No. 600/610 into vertical joints until completely filled.

Temperature of Capping Plate

Maintain an optimum temperature of 85°F to 90°F on the capping plate to prevent thermal shock and potential cracking when molten material is poured into the capping plate.

Estimating Table - material quantities per square foot

The above quantity requirements are based upon physical dimensions of chemical-resistant masonry units and actual weight of mortar as determined by ASTM C905. Actual usage rate will vary dependent upon scope of installation, experience of workmen, field conditions and other contingencies. Personnel using the above chart should, therefore, add an appropriate wastage factor.

600 & 610 will harden upon cooling. Allow minimum of two hours after hardening before placing into service or crushing capped specimens.

600 & 610 flake form is packaged in 50 lb. bags on plastic-wrapped pallets and the ingot/briquettes come ten (10) 5-lb. pieces per case.

620 Wood Spacers are 500 pieces/lb.

Unused material left in the melting kettle can be removed by chipping after it has cooled.

Sauereisen 600 & 610 have a shelf life of one year when stored in unopened, tightly sealed containers in a dry location at 70°F. If there is a doubt as to the quality of the materials, consult a Sauereisen representative.

Consult Safety Data Sheets and container label Caution Statements for hazards in handling these materials.

We warrant that our goods will conform to the description contained in the order, and that we have good title to all goods sold. WE GIVE NO WARRANTY, WHETHER OF MERCHANTABILITY, FITNESS FOR PURPOSE OR OTHERWISE, EXPRESS OR IMPLIED, OTHER THAN AS EXPRESSLY SET FORTH HEREIN. We are glad to offer suggestions or to refer you to customers using Sauereisen cements and compounds for a similar application. Users shall determine the suitability of the product for intended application before using, and users assume all risk and liability whatsoever in connection therewith regardless of any suggestions as to application or construction. In no event shall we be liable hereunder or otherwise for incidental or consequential damages. Our liability and your exclusive remedy hereunder or otherwise, in law or in equity, shall be expressly limited to our replacement of nonconforming goods at our factory or, at our sole option, to repayment of the purchase price of nonconforming goods.

  • Distributors and agents in major cities throughout the world. Consult manufacturer for locations.
  • Information concerning government safety regulations available upon request.
  • Sauereisen also produces inorganic compounds for assembling, sealing, electrically insulating and grouting

Customer reviews

No reviews were found for Sauereisen - Model No. 600/610 - Sulfur Base Mortars Basolit/Carbon Basolit. Be the first to review!