SURCIS - Model BM-Advance Pro - Multi-Purpose Respirometer System
From BM Multi-purpose Respirometry System
BM-Respirometer specially developed for practical and efficient biological wastewater treatment management, design and research.
- Compact analyzer, with very low maintenance and user friendly operation
- Direct oxygen measurements from a maintenance-free oxygen sensor
- No oxygenation restriction during test performance
- Full control and results by means a powerful software already loaded in the PC of the system
- Automatic software update versions from internet
- Capacity for test conditions setting and modify them throughout the test performance.
- Automatic measurements: OUR, SOUR, bCOD, rbCOD, sbCOD, U (COD utilization rate) and q (specific U)
- Last, minimum, maximum and moving average results throughout any moment of the test
- Several results at any time during the test and option to see them simultaneously on tabular or graphic modes
- Option to open several stored tests and compare their results
- Automatic temperature control integrated in the own console
- pH monitoring and automatic control system
- ORP monitoring
- Package of measurements at any moment during test performance
- Capacity for different respirograms and simultaneous overlying
- BM respirometers measure data that can be directly input into modeling – simulating software
- Option for a special reactor assembly for moving beds bio-films (MBBR)
From a mixed-liquor of the aeration tank it is determined the OUR & SOUR within the time and section we have selected in the corresponding respirogram.
Our (mg/l.h) Total oxygen uptake rate from mixed-l...
- Our (mg/l.h) Total oxygen uptake rate from mixed-liquor.
- Sour (mg/g.h) Specific OUR
On this mode, the analyzer performs a respirogram within a programmed DO threshold and determines the corresponding OUR & SOUR in base of a continuous sequentially measurements.
A DO base line is fixed from an endogenous respiration activated sludge and then added a certain amount of sample to be analyzed. In the respirogram, continuous measurements of Rs are showed permitting the simultaneous and continuous determination of CO and bCOD. In this way we can track the values evolution along the time as an actual window of the substrate oxidation from activated sludge.
- Rs (mg/l.h) Exogenous respiration rate corresponding to the substrate oxidation.
- Rsp (mg/g.h) Specific Rs.
- CO (mg/l) Consumed oxygen accumulated in the substrate oxidation (BODst)
- bCOD (mg/l) Biodegradable fraction of total COD (bCOD) or Readily biodegradable fraction of COD (rbCOD)
- U (mg COD/l.h) Substrate utilization rate
- q (COD/SS.d) Specific substrate utilization rate
Oxygen requirement and energy optimization
- Actual oxygen requirement for any specific process.
- Optimal and minimum DO level in the aeration tank, without any detriment of the process efficiency.
Bioaugmentation control and tracking
- By means the regular respiration rate measurement we can asses the result of the augmentation effect, to know if it is necessary to increase the dose of biomass and when it has reached its maximum effect.
- Automatic calculation of the COD biodegradable fraction (bCOD) or COD readily biodegradable (rbCOD)
Many times the COD fractions can be determined by ...
Many times the COD fractions can be determined by a single R test
Influence of the temperature, pH and oxygen and ot...
Influence of the temperature, pH and oxygen and other conditions
- Thanks to the capacity to set and modify the test conditions, we can analyze the influence of any of them (or any combination) in the biomass activity and figure out break-points, optimum and minimum working levels.
Operative parameter optimization
Operative parameter optimization
- Loading rate (F/M), Sludge age (SRT) y Returned sludge rate (RR).
- Nitrification rate (AUR), Specific nitrification rate (SAUR, qN), optimal DO range for nitrification, Necessary hydraulic time for ammonium-nitrogen removal, Nitrification capacity, minimum sludge age for nitrification (SRTN)
- Starting from the actual value of rbCOD, it is possible to determine the actual nitrate concentration that the process is capable to remove.
- Starting from the specific respiration rate of the anoxic biomass, it is possible to estimate the corresponding denitrification rate (NUR)
- All kind of applications derived from the analysis of the ORP evolution during the denitrification process.
- All kind of applications derived from the analysis of the ORP evolution during the anaerobic process.
- Toxicity to any specific biomass by different procedures to be applied depending of the case..
- For heterotrophic and autotrophic biomass.
- Aeration cycle control in SBR systems.
Biomass carrier (MBBR)
- Same applications as normal reactor + Amount of oxygen needs to maintain the biomass carriers under optimal conditions.
Support for simulation programs
Support for simulation programs
- Such as GPS-X, BioWin, …
- BM respirometers are open systems and, as such, support all kinds of combinations to step into an endless number of applications.
BM-Advance Pro - Technical Specifications
- Type: Optimized batch with closed recirculation.
- Use: Laboratory.
- Oxygen sensor: Maintenance free oxygen sensor. It is not necessary to replace neither membrane nor electrolyte
- Dissolved oxygen (OD), Temperature, pH and ORP.
- OUR & SOUR, Rs & Rsp, CO (Consumed Oxygen) and bCOD determinations.
- Calculation of U (Substrate utilization rate) and q (Specific U)
- Measurements visualization on tabular and graphical modes throughout the time.
- Overview of the results package at any time. Data acquisition interval setting.
- During the test, we get the last, minimum, maximum and average values.
- pH control: In the test configuration it is possible to set the pH at which it should be performed and change it at any time during the test.
- Test files:
- Automatic generation of a security file just when the test is starting.
- Possibility to save any test under the own software format and/or Excel.
- Operation modes: Static, Cyclic and Dynamic controlled by a specific software loaded in the PC of the system. Automatic respirograms generation thorughout the test. Preset test conditions (T, DO, pH, sample volume,…) and possibility to change them during its performance.
- Aeration system: From a small air compressor and a ceramic diffuser. The air flow can be controlled by means the software for different percentages of air supply for a non limited time.
- Respirograms: Automatic generation of graphic respiromgrams with the possibility to overlay them for comparison. Zoom application for total or partial periods. Option for the simultaneous visualization of several data displays under tabular and/or graphic modes.
- Partial measurements: During the test and to its finalization there is the option to get selective partial measurements from the values table or from any selected period of the respirogram.
- Dynamic calibration: Only for R mode the measuring system is calibrated by means the reaction of a chemical standard in distilled water, where the total oxygen demand is already known.
- Biomass-carrier reactor: Option for a special reactor for biomass carriers to get all respirometry applications for reactor any MBBR process type.
- MBBR reactor: Option for a special reactor assembly for moving beds bio-films (MBBR)
- ORP Mesurement: ORP measurement during the test on application for aerobic, anoxic and anaerobic processes.
- Temperature: 10 to 50º C, by means a peltier & heating system, installed in the analyzer console, controlled by the software
- Ouput: RS232 (for console ↔ PC communication)
- Display: LCD in sensor controller, LEEDS in front panel and PC screen.
- Power: 230 ACV or 115 ACV (under demand) 50/60 Hz - 300 W
- Dimensions/Weight: 50 x 40 x 46 (wide x deep x high) / 38 kg
No reviews were found for SURCIS - Model BM-Advance Pro - Multi-Purpose Respirometer System. Be the first to review!