TDHI - Model TD-4100XD - General Purpose Oil in Water Monitor
The TD-4100XD General Purpose monitor is a lower cost version of the industry standard TD-4100XD and is designed for use in non-explosive atmospheres. It was designed for dirty water applications and uses our standard EZ Access noncontact flow cell for lower maintenance. Field validation is via our CheckPOINT™ solid calibration check standard.
Unique Features
- Fluorescence measurement technology with lowest detection limits available
- Minimal sample conditioning plumbing hardware reduces cost
- Easy calibration with long term stability
- Low maintenance
- User friendly. E09 Electronics Package
- Ruggedized for harsh environments, non-hazardous areas
- Custom configurations and wetted materials
Specifications
- Applications: Steam Condensate, Boiler Feed, Normally Clean Water, Cooling Water, Intake Protection and Dirty Water with Chemical cleaning if needed
- Hydrocarbons: Fuel Oil, Crude Oil, Other Fuels and Lubricating Oils, Phenol, Styrene, Most Heat Transfer Fluids, Aromatic Chemicals, BTEX
- Detection Range: Fuel Oil, Crude Oil 5 ppb - 500 ppm in steam condensate
- Low Detection Limit: Most Other Hydrocarbons < 50 ppb
- Dimensions (Wall Mount): 44' Hx44' Wx 12.5' D (1118 mmx 1118 mmx 317 mm)
- Weight: 65 lbs (30 kg)
- Local Display: Yes, PPM, PPB, or Raw Signal
- Controls: External 316 SS Touch Pad
- Power Requirement: 90 - 240 VAC, 50/60 Hz +/- 10%, 184 W, 1 ph, (24 VDC Optional)
- Plumbing Requirements: Feed: 1/2' FNPT Return: 1- 1/2' FNPT Pipe
- Sample Inlet: < 20psig (1 38 kPag) (For higher pressures consult factory)
- Feed: 1/2' FNPT Return: 1- 1/2' FNPT
- Sample Outlet Pressure: Atmospheric (standard) or optional sample return pump
- Sample Temperature: 140 °F (60 °C) (For higher temperatures consult factory) 2 - 3 US gallons/min [7.5 -11.5 L/min], optional sample pump
- Required Inst. Air Supply General Purpose: 10 - 20 SCFH (0.28-0.57 m3/hr)
- Ambient Operating Temperature: -4 to 131 'F (-20 to 55 'C) (Heater or Vortex Cooler Optional)
- Flow Cell Characteristic: Non-Contact EZ Access
- Pressurized Sample Return: Yes, with optional sample return pump
- Operational Principle: UV Fluorescence with application specific optical configurations
- Calibration Stability: +/- 10% over 6 Months or better
- Response Time: 3 seconds full scale spike change, continuous reading
- Calibration: Blank / standard addition or correlation to standard methods linear or non-linear
- Field Validation: Via CheckPOINT Solid Check Standard
- Reagents: None
- Alarms: Baseline, early warning, high alarm, system-function, local display and audible tone
- Alarm Contacts: Four user-sertable, independently-protected dry contact relays
- Communication: Standard E09 features with 4-20 mA isolated, 500 ohm impedance, selectable between Loop Powered and Instrument Powered, Ethernet. Optional HART, ModBus
- Diagnostics: System failures reports to relay and local display
- Security: Two level password protected, lockable cabinet
- IP Rating: IP 66, NEMA4X (Standard)
- Maintenance: Calibration check, Clean Sample System
- Hazardous Area Options: Use TD-4100 XD with proper rating
- Sample Pump: Optional
- Cleaning System: Optional
- Data Logger: Standard - see E09 Data Sheet
- ISO Certified 9001: 2008 Quality System
Applications
Not for use in explosive atmospheres
Produced Water
- Overboard discharge compliance and process control
- Re-injection or water flood water quality control
- Produced water reuse – RO feed water, steam generator feed water
- Noncontact cooling water
Heat Exchanger Leak Detection
- Boiler feed protection
- Cooling tower protection
- Open-loop discharge
Wastewater
- Process water discharge
- Industrial discharge
Marine Water
- Drilling and production rig slop tanks/deck drains
- Bilge water discharge
- Ballast water discharge
Other Water Types
- Hydroelectric water
- Storm water
- Groundwater
- Municipal wastewater
- Potable water
Hydrocarbons Detected
- BTEX
- Gasoline
- Diesel
- Jet fuel
- PAH’s (polycyclic aromatic hydrocarbons)
- Creosol
- Crude oil
- Heat transfer fluids
- Aromatic solvents
- Aromatic chemicals (styrene, phenol, etc.)
- Lubricating oils
- Fuel oil
- Longwall fluid