Cone Penetration (Geophysics) Equipment Available In Netherlands Antilles
-
Manufactured by Ingenjorsfirman Geotech ABbased in SWEDEN
Seismic test are carried out to measure shear (S wave) and compression wave (P wave) velocities in soils. The SCPT method combines the seismic test with results from the CPTU probe, and will give you a good basis for evaluation of a number of critical soil properties, e.g. the risk for ...
-
Manufactured by Pagani Geotechnical Equipment s.r.l.based in ITALY
The CPT test (mechanical type) is essentially the extent of resistance to opening up a bit of size and mechanical characteristics standardized, stuck in a land-speed constant (2 cm / sec). In Cone Penetration Testing, with the Begemann Mechanical Cone, the Qc (tip resistance) and RL (side friction) values are measured with a load ...
-
Manufactured by Geoquip Marine Operations AGbased in SWITZERLAND
The GMC201 is an efficient and low cost seabed CPT system for seabed penetration depths down to 40m, in water depths down to 3000m. This Geoquip Marine designed and built seabed CPT system can be rapidly deployed from a crane ship or drilling ship and is the tool of choice for conducting tests ...
-
Manufactured by Geomil Equipment B.V.based in NETHERLANDS
The Manta-200 represents the latest generation Cone Penetration Test (CPT) system for determining offshore seabed soil conditions. Deployed from a steady positioned vessel or platform, the Manta-200 is designed for rapid and reliable ...
-
Manufactured by Geoquip Marine Operations AGbased in SWITZERLAND
The GMC202 is a cost effective seabed CPT solution for seabed penetration depths down to 40m or more should soil conditions allow, in water depths down to 1500m. The units are renowned for their overall durability and high production rates which make them ideally suited to largescale scopes of work especially in variable ground ...
-
Manufactured by Geoquip Marine Operations AGbased in SWITZERLAND
The GMC200 is an efficient and low cost seabed CPT system for seabed penetration depths down to 40m, in water depths down to 2000m. This Geoquip Marine designed and built seabed CPT system can be rapidly deployed from a crane ship or drilling ship and is the tool of choice for conducting tests ...
-
Manufactured by Geonor ASbased in NORWAY
A new model of the Geonor G-200 Fall Cone Penetration Test including a robust special purpose transport box and a flexible magnifier is now available. Application The Fall Cone Penetration, first introduced in 1915, provides a rapid, simple and accurate method for determining empirically the undrained shear strength, the shear ...
-
Manufactured by Geomil Equipment B.V.based in NETHERLANDS
The Geomil Equipment Lizard-200 is a hitch-up Cone Penetration Testing (CPT) system to be used in combination with an excavator. It allows for conducting CPT’s in near to impossible conditions, such as sites where space is limited and ground anchors cannot be ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
By incorporating the patented ST-Rods in the ROSON seabed system, a compact and easy to handle ROSON-ST is created. It is suitable for 50 m penetration of 40 mm rods, works with all Icone sizes and click-on modules and does not require any exterior CPT string support, assuring fast deployment and high productivity. The use of standard 40 mm ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
For water depths between 30 and 300 m the near-shore ROSON is a suitable solution. This ROSON is available with 50 kN, 100 kN or 200 kN pushing force. To avoid the investment in a self-tensioning winch, data communication runs over a free hanging cable to the Icontrol data logger. At water depths up to 30 m a jack-up barge or pontoon is often used. As long as the influence of currents and the ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
The various ROSON systems come with an electric driven winch with self-tensioning for heave compensation. A CPT depth up to 50 m is feasible. Data communication from the ROSON to deck level is achieved by a powerline connection through the umbilical. This is realized by a transducer at both ends of the umbilical. These transducers, called Icone Powerline Adapters, convert the Icone signal to a ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
The DW (Deep Water) ROSON, with its proven wheel drive CPT system, is provided with technology to perform CPT’s and samples in harsh offshore conditions at ultra-deep waters. The DW ROSON is unrivalled in the ...
-
Manufactured by Ingenjorsfirman Geotech ABbased in SWEDEN
With the ECPT sensor you measure the conductivity of the soil while performing standard CPTU test. Test results can be used for analysing salinity and detection of pollutants. The electric conductivity sensor is mounted on Geotechs 10 cm2 CPTU probes. The adapter consists of an array of four ring electrodes (Wenner configuration, i.e. with equal spacing between the electrodes). The CPTU probe ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
The most compact & lightest self-propelled unit is the Mini CPT Crawler. The Mini CPT Crawler consists of the well-proven single cylinder HYSON 100 kN-LW with 10 ton pushing force. With a weight well under 1,600 kg and a width of only 780 mm the Mini CPT Crawler fits trough a doorway and can be transported in a mini van. The pusher is dismountable, so it can also be used as a stand-alone unit ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
The versatile high-performance CPT unit was invented by A.P. van den Berg and has a track record of more than 25 years. With its tracks retracted, the Track-Truck can run on the highway as an ordinary truck. After lowering the tracks, the Track-Truck is in its element in soft and hilly terrain where other heavy vehicles get stuck. Even ditches are easily conquered. The track system reduces the ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
The CPT Crawler provides the same high production rates and reliability as the CPT Truck, with the advantage of tracks for better manoeuvrability in rough or soft terrain. The crawler is the only option at sites where the maximum allowed height is limited. Of course a separate carriage is required for transport of the crawler. The twin-cylinder HYSON 200 kN can be built on a 15 tons crawler which ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
A CPT Crawler that is based on an existing crawler vehicle is the CPT Morooka Crawler, a relatively fast CPT Crawler for very soft soil. The unit is built on a low ground pressure 15-ton crawler chassis. The rig is fast (with speeds of over 12 km per hour) and can travel long distances on asphalt or concrete surfaces without causing surface damage. The crawler tracks are made of rubber. The ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
of the truck is reinforced with a sub frame to take the forces occurring during the Cone Penetration Tests. The truck’s total weight is sufficient to provide the maximum pushing force. The well-proven twin cylinder HYSON 200 kN penetrometer is installed in the CPT Truck. The hydraulic upper clamp is an effi cient addition to the ...
-
Manufactured by A.P. van den Bergbased in NETHERLANDS
The Midi CPT Crawler is a compact and manoeuvrable CPT system, with a maximum power of 20 tons. The Midi CPT Crawler consists of the renowned CPT penetrometer (HYSON 200 kN) mounted on an undercarriage with rubber tracks. With a weight of about 3,500 kg and a width of only 1200 mm the Midi CPT Crawler fits trough small passages and can be transported in a small truck. To provide the required ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
The jacket cone (also called the M1 cone or mantel type cone) is used for mechanical cone penetration testing and is suitable for measuring the cone resistance (qc) and the total resistance ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you