Geonor Soil And Groundwater Equipment Available In Kyrgyzstan
-
Manufactured by Geonor ASbased in NORWAY
A new model of the Geonor G-200 Fall Cone Penetration Test including a robust special purpose transport box and a flexible magnifier is now available. Application The Fall Cone Penetration, first introduced in 1915, provides a rapid, simple and accurate method for determining empirically the undrained shear strength, the shear strength of remolded samples and thus the sensitivity of clays. The ...
-
Manufactured by Geonor ASbased in NORWAY
The P-520N frequency counter is the read-out instrument for all GEONOR vibrating-wire transducers. The counter is designed for use in situ and is enclosed in a rigid aluminium housing. The display shows the frequency of vibration in 0.1 Hz. which has to be calculated to physical units using a calibration table. It is powered by a rechargeable 12 V NiCd ...
-
Manufactured by Geonor ASbased in NORWAY
Effective sample length for the K-500 model is 700 mm. The sampler can be used on drilling rigs without disassembling rods and sampler between each sampling. K-500 model is equipped with replaceable edges. One thin-walled head intended for undisturbed samples of silt and clay and one coarse head for sandy soil. Sand catcher can be used together with a rough cutting ...
-
Manufactured by Geonor ASbased in NORWAY
The field vane shear lest (FVST) is the most commonly used method for measuring the undrained shear strength of soft to stiff clays. For this reason, a preliminary investigation of soft clays with a hand-held vane tester is both economic and fully relevant. It also has good repeatability and is quick in providing valuable information for the planning of more detailed ...
-
Manufactured by Geonor ASbased in NORWAY
The Geonor M-600 series piezometers are vibrating wire sensors which are installed by pushing into soft and loose soils without having to drill a borehole. As with all other Geonor vibrating wire piezometers, the M-600 series offer the maximum reliability available for continuous pore water pressure or ground water level measurements. Geonor *s unique design combined with continued technical ...
-
Manufactured by Geonor ASbased in NORWAY
This Soil Sampler K-200 model comes with the test cylinder of steel with max. sample lengths of 800 mm, min. 500 ...
-
Manufactured by Geonor ASbased in NORWAY
P-430 is a steel reinforced 2-pair cable. It is specially designed to withstand high loads in terms of tension and compression and is protected against water ingress, in case of damaged ...
-
Manufactured by Geonor ASbased in NORWAY
The Geonor M-610 scries arc vibrating wire piezometers used for direct burial in embankments and earth/rockfill dams, for placement in boreholes, and for water level monitoring in open wells, tanks, and open bodies of ...
-
Manufactured by Geonor ASbased in NORWAY
The Geonor H-70 field inspection vane tester was originally developed in Norway for the special task of preliminary invetigations in soft clays without preboring. It is a comparatively low-cost, still fully professional instrument. The Geonor H-70 allows for safe vane boring down to 10 meters by simple hammering, drilling or pressing. It is a lightweight instrument that can be carried by a single ...
-
Manufactured by Geonor ASbased in NORWAY
The field vane shear test (FVST) is the most widely used method for measuring the undrained shear strength and sensitivity of soft clays in-situ. FVST is a more economic method than for example CPT, as its operation does not require a drilling rig or highly qualified ...
-
Manufactured by Geonor ASbased in NORWAY
Geonor T-200B series of all-weather precipitation gauges are used by leading meteorological services and climatic networks worldwide. Other users are typically airport authorities, agricultural institutes and hydroelectric ...
-
Manufactured by Geonor ASbased in NORWAY
The piezometer can be pressed down without pre-drilling, normally until approximately 30 m depth. Intended for Ø32 mm extension tube. Adapters to 1' water pipe can be ...
-
Manufactured by Geonor ASbased in NORWAY
M-603 is a special version of M-600 which is open to the atmosphere and equipped with a rubber membrane above the pressure membrane. Compressed air assistance provides a back pressure in order to relieve the pressure membrane. This will balance the back pressure during push-in penetration and the piezometer will be pressed down more quickly. Back pressure can also be used to relieve the membrane ...
-
Manufactured by Geonor ASbased in NORWAY
Effective sample length for the K-100 model is 700 mm. The sampler can be used on drilling rigs without disassembling rods and sampler between each sampling. The K-100 model is equipped with replaceable cutting head. One thin-walled head intended for undisturbed samples of silt and clay and one coarse head for sandy soil. Sand catcher can be used together with a rough cutting ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you