Water Pumping Equipment In Papua New Guinea
-
Manufactured by Mueller Water Productsbased in CANADA
The 106-RPS-D and 206-RPS-D pressure differential sustaining valves are based on the 106-PG or 06-PG main valve. The RPS-D uses the 81-RPD pilot valve and has two sensing connections. The valve and pilot remain closed until the difference between the two pressures exceeds the pilot setting. Under flowing conditions, the pilot reacts to small changes in pressure to control the valve position by ...
-
Manufactured by Mueller Water Productsbased in CANADA
The SAP surge anticipator panel provides the interface between a customer supplied, system pressure switch and the Singer surge anticipating control valve. Together they provide protection against destructive pressure surges. The SAP panel energizes the control valve pilot solenoid on an abnormally low pressure reading and/or power failure to pumps. The 12 VDC pilot solenoid is energized to open ...
-
Manufactured by Mueller Water Productsbased in CANADA
The 106-HC and 206-HC hydraulic check valves are based on the 106-PG or 206-PG main valve. The valve functions as a two position valve - either fully open or fully closed. The HC allows one way flow only. Under normal forward flow, the valve opens as the higher inlet pressure lifts the inner valve assembly and the fluid in the upper chamber is discharged to the lower pressure, downstream side of ...
-
Manufactured by Mueller Water Productsbased in CANADA
The 106-DW and 206-DW deep well pump control valves are installed in a tee between the pump discharge and the check valve. The valve is normally open, and, on pump start-up, a pilot solenoid is energized to start closing the valve at a rate governed by the closing speed ...
-
Manufactured by Mueller Water Productsbased in CANADA
The Singer models 106-2SC-MV and 206-2SC-MV electronic flow control and metering valves are based on the 106-PG or 206-PG main valve. The pressure in the upper operating chamber is controlled by operating the pilot solenoids. The PLC within the MV1-TP control panel determines whether the opening solenoid or the closing solenoid is operated. The change in valve position is dependent upon which ...
-
Manufactured by Mueller Water Productsbased in CANADA
The SPC pump control panel provides the interface between the pump motor starter and the Singer pump control valve. The SPC ensures that the pump starts and stops without causing line ...
-
Manufactured by Mueller Water Productsbased in CANADA
Micrometer flow control valves allow for precise flow control. There is full flow in one direction and adjustable restricted flow in the opposite direction. They are standard on certain models, such as BPC pump control valves and available as an option for other applications. Standard end connections are female-to-female 1/4 in / 6.35 mm ...
-
Manufactured by Mueller Water Productsbased in CANADA
The A106-Dynamic Lifter (DL) sewage pressure relief valve is a direct acting spring loaded relief valve. The valve is adjusted to open when the pressure exceeds the set-point, which is approximately 10% above the normal operating pressure. The valve closes drip-tight when pressure falls below the set-point. The DL is connected on a tee off the main line and usually discharges relief flow back to ...
-
Manufactured by Mueller Water Productsbased in CANADA
The 106-PT and 106-PTC series control valves are hydraulically operated by introducing or releasing water from the control chambers. PT and PTC valves have two operating chambers that are divided from each other by the diaphragm, and are separated from the flowing media by an adaptor ...
-
Manufactured by Mueller Water Productsbased in CANADA
The 106-PG-BPC or 206-PG-BPC booster pump control valve is installed in-line directly downstream of the pump discharge. The valve is normally closed, and, on pump start-up, a pilot solenoid is energized to slowly open the valve, at a rate governed by the opening speed control. The pipeline flow is gradually ...
-
Manufactured by Mueller Water Productsbased in CANADA
The 206-PT and 206-PTC series control valves are hydraulically operated by introducing or releasing water from the control chambers. PT and PTC valves have two operating chambers which are divided from each other by the diaphragm, and are separated from the flowing media by an adaptor ...
-
Manufactured by Mueller Water Productsbased in CANADA
The 106-BPC and 206-BPC booster pump control valves are installed in-line, directly downstream of the pump discharge. The pump control valve is normally closed and on pump start-up, a pilot solenoid is energized to open the valve, at a rate governed by the opening speed control. When shut-down is required the pilot solenoid on the valve is de-energized to commence closing. The pump is kept ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you