Hydrocyclones Equipment For Water And Wastewater Available In Nepal
-
Manufactured by Salter Cyclones Ltdbased in UNITED KINGDOM
Salter Cyclones new Hydrocyclone designs, from 10mm to 10 inch (250mm), accommodate a wide range of flow rates and provide precise control of cut points and other performance criteria. These Hydrocyclones are available with different sizes of vortex finders and spigots and are manufactured from highly wear resistant polyurethane, suitable for operating temperatures up to 130°C or, where there ...
-
Manufactured by Aipu Solids Controlbased in CHINA
All the equipments will request wearing parts. Usually we treat 12 months as a guarantee time. We kindly suggest users replace wearing parts after about one year operation. Aipu provide spare parts for you including hydrocyclones, mechanical seal, hopper, bearing, impellers, etc. If you need more info just contact us ...
-
Manufactured by REKO Industrial Equipment b.v.based in NETHERLANDS
Separation of starch, sand and other settling solids from waste water and process water by means of centrifugal forces.Efficiency.The efficiency of the hydrocyclones is depending on the solids density, liquid density, feed pressure, ...
-
Manufactured by Shijiazhuang Ruite Pump Co.,Ltd.based in CHINA
TSP(R) Vertical Slurry pumps are vertical centrifugal slurry pump that in liquid to handle abrasive ,large particle high concentration slurries. It can operate normally without shaft gland and shaft gland water, even lack of intake. TSP pump body is made form antifriction metal, the impeller is made from antifriction metal or rubber and polyurethane. Submerged parts of the TSPR pump coated rubber ...
-
Manufactured by Hebei Tobee Pump Co.,Limitedbased in CHINA
Tobee®Slurry pump volute Liner D3110A05A, D3110A05, D3110A49, D3110A61 are curved funnel increasing in area to the discharge port. It is often used together with impeller for slurry pumps. As the area of the cross-section increases, the volute reduces the speed of the liquid and increases the pressure of the liquid. The main purposes of a volute casing is to help balance the hydraulic pressure on ...
-
Manufactured by Zorg Biogas GmbHbased in GERMANY
Hydrocyclones are used in biogas plants to separate solid inclusions from substrates: sand, soil, mineral sediments and small stones. Substrate is fed into the upper part of the hydrocyclone in the tangential direction. Centrifugal acceleration causes the particles to move to the separating cone wall, from where they sink into the dirt trap through an intermediate pipe, followed by the clean ...
-
Manufactured by Binder Cobased in AUSTRIA
Binder+Co supplements its product range in the wet processing of building materials by attrition machinery and sieve jiggers. Attrition machinery is used for dissolving loamy lumps and cleaning sand. Binder+Co provides sieve jiggers to separate light materials (e.g. wood) from grit. Binder+Co supplies dewatering screws and spiral classifiers for dewatering sand from hydrocyclone or screen ...
-
Manufactured by Aipu Solids Controlbased in CHINA
Mud cleaner is the second and third phase solids control equipments. Aipu main mud cleaners are Hunter series. Aipu mud cleaners give you following benefits: ...
-
Manufactured by FLSmidthbased in USA
Performance and longevity: benefit from both with Urethane Cyclones; Most separation equipment demands you make a choice. You end up sacrificing production, wear life and even end product quality looking for the best solution to your wet processing needs. Our Urethane Cyclones are different. You gain the best of all worlds from capital outlay to capacity to quality to long wear life. Ease of ...
-
Manufactured by Blasch Precision Ceramics, Inc.based in USA
Blasch high performance monolithic drop-in replaceable silicon carbide liners are specifically engineered for classifying applications in sizes up to 60 inch diameter. These liners are designed for highly abrasive ores process such as coal, iron ore, gold, copper, cement, FGD and phosphate mining. With a variety of highly abrasion-resistant compositions available, both OEMs and single plants can ...
-
Manufactured by CECO Environmentalbased in USA
Deoiling Hydrocyclones were developed for the offshore oil industry in the 1980s and rapidly became established as standard equipment used for recovery of oil from Produced Water streams in both onshore and offshore applications. The deoiling hydrocyclone vessel is designed to reduce the oil content of the incoming produced water prior to entering an optional degasser vessel. Hydrocyclones are ...
-
Manufactured by ANDRITZ Separation - ANDRITZ Groupbased in AUSTRIA
In continuous solid/liquid separation, Krauss-Maffei pusher centrifuges combine high availability with minimum maintenance and reduced specific space requirement. They enable effective dewatering of fast filtering products at high throughput rates. The quality of the final product can be increased using a variety of washing modes. Krauss-Maffei pusher centrifuges are applied in many fields of ...
-
Manufactured by Elgin Separation Solutionsbased in USA
The vacuum degasser is the most common form of degassing systems used in the oil & gas industry. Drillng fluid is pulled into the tank by vacuum action. The fluid rises inside the tank and is distributed over a series of plates which releases the gas bubbles from the drilling fluid. The gas is pumped out of the system and the fluid transferred to hydrocyclones or a centrifuge for further ...
-
Manufactured by Hebei Tobee Pump Co.,Limitedbased in CHINA
Tobee®Slurry pump volute Liner D3110A05A, D3110A05, D3110A49, D3110A61 are curved funnel increasing in area to the discharge port. It is often used together with impeller for slurry pumps. As the area of the cross-section increases, the volute reduces the speed of the liquid and increases the pressure of the liquid. The main purposes of a volute casing is to help balance the hydraulic pressure on ...
-
Manufactured by Energy Specialties International (ESI)based in USA
Tests at a major University show that ESI's new Spiral Ramp LQ-R's design can improve the efficiency of hydrocyclones by as much as 50% (see graph). Converts pressure energy to internal centrifugal energy. Geometry creates vortex to enhance gravity. Oil droplets coalesce in central code (> 5-20 microns). Insensitive to motion or surges. No moving parts. Light Weight. Unaffected by Motion. No ...
-
Manufactured by Rivulis Irrigation, Ltdbased in ISRAEL
The F1000 Hydrocyclone Sand Separator creates a centrifugal action that moves the water around the edge of the body, throwing the sand and heavy materials to the outside of the cyclone. The heavy materials then fall into the underflow chamber to be collected. Rivulis provides the proper sized underflow chamber to match the performance of each size of hydrocyclone sand separator, preventing the ...
-
Manufactured by AR Agricultural Irrigation Companybased in TURKEY
In-Out Inch: 2" Manshon. Flow Rate (m³/h) min-max: ...
-
Manufactured by Matec Solutions Co.,Ltd.based in CHINA
Applications: As an universal separating and classifying equipment, widely used for mineral processing, desliming, thickening and also dewatering operations. Features & Specifications: Dimension accuracy and Compatibility is guaranteed; Superior abrasion resistance for a longer wear life. High wear resistant Polyurethane Polyurethane elastomer is of high strength, corrosion resistance, light ...
-
Manufactured by Lessine SAbased in BELGIUM
With an output size going up to 5µ, the ball mill has a proven its ability to grind many materials whatever hard they ...
-
Manufactured by Tons Per Hour, Inc. (TPH)based in USA
Tons Per Hour, Inc. offers a full range of fines recovery, scrubbing and classification cyclones. Both traditional hydro-cyclones and vacuum/syphon assisted cyclones for reducing underflow moisture and sand stacking ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you