Only show results available in Virginia? Ok

Water and Wastewater Equipment with Municipal sludge dewatering applications

  • Premium

    Intereco - Skid Plant for Sludge Treatment

    The SKID plant is bom to have a movable sludge dehydration plant: it is fitted on a strong shapes frame and it is suitable to be installed on trucks, to be transported and settled in the working site. The skid plant is provided with four strong lifting hooks, to he hoisted with crane or suitable-lift platform truck (skid weight depends on ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model EM 5 & EM 10 - Manual Polyelectrolite Preparation Unit

    Manual polyelectrohte preparation unit all made in AISI 304 stainless steel with all necessary components mounted on board. The unit is complete with electrical impeller, water feeder, dosing pump with flowmeter, post-dilution device. The solution can be prepared at a concentration ranging between 0.5% and 1% then is diluted at about 0.1% with the ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model CONE - Conic Sludge Mixer

    Special conic mixer CONE useful to realise a good and continuous mixing between sludge and polyelectrolite solution. It is made with a conic part in which sludge is fed through a DN 100 PN 10 pipe, with a 90 degrees elbow and delivered through a DN 80 PN 10 flange. After the elbow and before the case, the flocculant is fed through four symmetric ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model TF Series - Belt Filter Press

    Belt filtering table TF is used instead of a static thickener, with expensive concrete works, to thicken sludge before a digestor or a following dewatering unit (as belt press, plate filter press, centrifuge).

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model EDOM/L - Belt Filter Presses

    EDOM/L Belt presses with a pre-gravity zone and a sludge turnover, in size from 500 to 1200 mm belts width. This model is particularly apt for sludge with a low solids content (below 1.5% SS). Achieved capacity increases are up to 50% compared to the same standard belt press EDOM.

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model Edom 1500 - 2000 - Belt Presses

    Robust side frames in high thickness angles and unp shapes. Completely welded and connected between themselves with bolted unp shaped. Completely high thickness hot dip zinc coating. Fasteners in a2 stainless steel. Metal net protections for easy washing of the belt press. Easily removable for maintenance. Protection over gears in aisi 304 s.s. ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model COC 200 - Screw Conveyor

    The screw conveyor COC 200 is made by a steel pipe (hot dip zinc coated or painted) with a 219 mm nominal diameter. The screw has a 200 mm diameter and so is its pitch.The unit is completed by bearings and greasers, feed hopper legs, driving groups with a swinging gear box , pulleys and belts to avoid crawling, safety protections. Under request ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model CAB 1500 - 2000 - Belt Presses

    After a twenty years long experience of units installed all over the World, INTERECO produce belt press to 3000 mm belts width. Apt for any type of sludge: Biological, chemical, paper milk dairy, inert and tanneries. To save money for the shipment, it is no necessary to use wood cages. For a belt press CAB 2000 is enough a 20” Flat Rack. ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Automatic Polyelectrolyte Preparation Unit

    Available current models 600 It (two tanks) ( BSB600), 1200 It, 2000 It (three tanks) (BTB 1200 AND BTB 2000) and, under request 3000 It, 4000 It and 5000 It. All models have a simple and reliable functioning. With a bar level controls the polyelectrolite preparation is activated to have always the polyelectrolite tank full. The polyelectrolite ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Granulator

    Manufactured in carbon steel, either painted of hot dip zinc coated. Available under request completely in aisi 304 s.s. Model gra 150 available with hopper for quick lime, completed by a dosing screw with mecanical speed variator and vibration device against bridges.

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model CRV Series - Vertical Cylindrical Reactor for the Best Sludge Flocculation

    Vertical cylindrical reactor CRV necessary to have the best flocculation, composed by a cylindrical hot dip zinc coated tank, is necessary for the sludge and poly mixing, made by a low speed mixer (18 rpm), to obtain the best sludge flocculation. The long contact time between sludge and poly before the sludge discharging, optimize the flocculant ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model NT - Belt Conveyor

    The belt conveyor NT is made with 'C' welded plates and with welded structural frame works. Supporting rollers are 'V' rollers perfectly sloped, ends locked by lubrificated and sealed bearings; rollers are 650 mm apart one from each other. Supporting return rollers are horizontal, made like the 'V' rollers and proportional to the belt length. ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model Rotoset Series - Dynamic Thickeners

    Dynamic thickener ROTOSET with a sludge capacity up to 60 m3/hr. The unit is complete with vertical cylindrical reactor with impeller for a perfect sludge/polyelectrolite mixing, with a centrifugal filter cloth washing water pump, able to recycle the thickener filtrate, this to avoid water consumption and the increasing of the WWPT hydraulic head. ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

  • Premium

    Intereco - Model Edom Series - Belt Presses

    EDOM belt presses cover a small-medium range (500 to 1300 mm width), used in small municipalities and industries with their water treatment plants. Standard production is made with frames in hot dip zinc coated carbon steel, rollers and tank in AISI 304 SS. On request, EDOM may be made entirely in AISI 304 SS or AISI 316 SS. Belt presses can be ...

    By Intereco S.n.c. based in Candiolo (TO), ITALY. from Sludge Treatment Plant Product line

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you